All Questions
42 questions
0
votes
0
answers
31
views
Fitting deadbolt strike with plate over plate-less one on a hollow metal door
I am trying to replace a deadbolt lock on my door (hollow metal one). The old lock is Mul-T-lock with a strike that doesn't have a plate (see photo). The new lock's strike is a standard in that it ...
0
votes
2
answers
96
views
Anyone knows how to remove this deadbolt/lock without visible screw?
Here is the picture, would like to change it without damage to it:
- 11
0
votes
1
answer
166
views
How can I remove this dual cylinder deadbolt?
The key for this lock is very rusty and old and barely works, so I want to replace the dual cylinder deadbolt lock, below the doorknob, with a new lock.
I don't see any screws on the deadbolt lock, ...
0
votes
2
answers
134
views
How do I fix a stuck deadbolt where the screws are obstructed?
The deadbolt in the picture is stuck in the locked position. There is some play in the deadbolt so it does not appear to be the case that the door is sagging or the plate is misaligned. I suspect ...
- 127
4
votes
1
answer
895
views
Deadbolt bracket hole (not "knob" hole) is too big
so I'm trying to replace an old double keyed deadbolt with a kwikset latched deadbolt in a very old front door. The "knob" holes for the deadbolt are a perfectly fine size, but the hole cut ...
- 41
4
votes
1
answer
410
views
My deadbolt isn’t retracting any more and turning it doesn’t do anythjng
I have a Schlage Encode and unlocking and turning the thumb turn. I was able to take it apart but doesn’t seem like it’s catching when I turn it manually. Also a piece fell out that I’m assuming may ...
0
votes
0
answers
92
views
How to install a deadbolt in a tight space?
Renting a home and trying to replace the deadbolt on the back door. However, the space where the lock slides in is very small and I can’t get the sliding piece into the door - the circled area is ...
- 1
2
votes
1
answer
689
views
Swapping a lock for a double cylinder
This is a european style lock where you turn the handle up for the strike to come out and then turn the little knob underneath to lock it. Can a DIYer convert this lock into the type where a key is ...
- 31
0
votes
0
answers
123
views
How to remove this deadbolt?
I have an older deadbolt and instead of a faceplate or screws it looks to just have two “blanks”, and no visible way to remove it. Anybody familiar and know how to safely remove a bolt like this? It ...
0
votes
0
answers
243
views
Schlage B62 Deadbolt Removal
Need help removing a Schlage B62 deadbolt from a front door. It’s a double sided one, and has no faceplate or screws for removal. Deadbolt is also stuck and won’t lock or unlock when key is in.
0
votes
2
answers
325
views
How can I install a door latch with a bore that's 1/8 inch too large?
I have a deadbolt lock for a smart lock I just bought. The first problem is I have a metal door and need a drive-in bolt attachment for the lock.
The second problem is the the hole I made in the door ...
- 1
1
vote
2
answers
2k
views
Cannot remove set screw in deadbolt thumb turn
I'm trying to remove the thumb turn on my door. There appears to be a set screw that's preventing the knob from coming off. I believe the manufacturer of the lock is Lawrence Hardware.
I have tried ...
- 11
1
vote
1
answer
446
views
Exterior entry door handle & deadbolt: What is a combined locking handle + deadbolt called?
I need to replace the setup below.
I have searched high and low, but cannot find the integrated setup for the interior (where the door handle and deadbolt are combined, so by just turning the door ...
8
votes
1
answer
2k
views
How can I remove this Kwikset entry door dead bolt lock?
This is a picture of the Kwikset dead bolt from interior. I removed the outer layer. However, I'm having trouble removing the bottom plate.
This looks very similar to this question: Removing old Entry ...
- 83
-2
votes
2
answers
3k
views
Smartkey rekey making multiple copies question
So I just installed smartkey door lock and deadbolt. I want to use my door lock to open the deadbolt lock and I followed the rekey instruction to make the door lock key open the deadbolt key. No ...
- 347
0
votes
0
answers
2k
views
Deadbolt will not unlock from inside if locked with key from outside and vice versa
Our office door deadbolt will only unlock with a key if locked with a key. If you lock it with the key from outside and then someone tries to unlock the deadbolt from inside with the knob, it won't ...
- 1
0
votes
0
answers
81
views
How to remove older Schlage deadbolt? [duplicate]
I just bought a house and want to replace the locks. Unfortunately, on door has what appears to be an older Schlage double cylinder deadbolt that I can't figure out how to remove. I've tried prying ...
0
votes
1
answer
4k
views
How to fix deadbolt lever that doesn't lock or unlock the deadbolt
I have a Bold deadlock on the front door of my apartment (I'm not sure exactly which model it is but it looks basically like this: http://boldlocksupply.com/premium-cylinder-deadbolt-d-8-gold/). A few ...
- 3
5
votes
2
answers
331
views
Question about outswing door on attached toolshed
I have a toolshed attached to my garage with an outswing door. The door appears to be screwed into the moulding instead of the stud. Is this typical for an outswing door (see photos)?
Photo album
I'...
- 153
1
vote
3
answers
130
views
Backplate for satin nickel deadlock
There is an old door with some marks from a jimmyproof lock. It was replaced with a single cylinder deadlock, satin nickel finish.
To cover the marks, it was decided to install a back plate covering ...
- 461
2
votes
2
answers
4k
views
Prevent deadbolt from turning?
I am a renter, so I cannot change the locks or drill an additional deadbolt. I came across August Smart Lock today (https://www.amazon.com/August-Smart-Lock-Pro-generation/dp/B0765LFNM7), which sits ...
user25400
-1
votes
1
answer
1k
views
Reconfigure metal door lock system from mortise to individual door knob and deadbolt
I have a metal door with a privacy mortise lock with a thumbturn.
I can't drill any new holes outside, we must use the existing hole for the door knob and deadlock.
I have to replace the existing ...
- 461
0
votes
1
answer
1k
views
Should I replace a knob lock when replacing a matching deadbolt? [closed]
I've got three external doors with Callan knob lock and deadbolt sets. The deatbolts on two of the doors have failed due to a part on the inside that has deteriorated.
I was hoping to replace the ...
- 167
1
vote
0
answers
9k
views
Installing a deadbolt lock on a metal door & metal frame
I live in an apartment where the front door and its frame are both metal and hollow inside. I didn't have trouble installing a deadbolt lock with one of the doors because you could remove the strike ...
- 11
1
vote
3
answers
2k
views
Which kind of locks should be installed on external wooden glass panel doors?
When you have an external glass panel door it may be simple for a criminal to break a pane of glass to access the handle and lock inside.
What types of locks are appropriate to install on a door of ...
- 217
3
votes
2
answers
5k
views
Ways to mitigate safety risks with double cylinder deadbolts on enterance/exit doors?
While double cylinder deadbolts (those deadbolts on house doors that require a key from both sides) can be good for security, it could be a trade-off with safety if needing to get out of the house in ...
- 1,692
0
votes
0
answers
58
views
Installing Kwikset Kevo on a door to control more than the deadbolt
I own door which the key not only controls the lock but also to open the door. There is no extra handle to open the actual door. You just turn they key once more and the door opens.
I wish to install ...
- 360
2
votes
3
answers
4k
views
Lock can be opened with credit card even when deadlatch is fully depressed
I just installed a standard deadlatch, very much like this:
The problem is, it can be opened from the outside with a credit card.
Of course, a properly installed deadlatch should make this ...
- 121
1
vote
1
answer
119
views
Replacing deadbolt
I'm replacing a deadbolt and need help for the next step. I've installed the exterior portion and I'm now installing the interior portion. The photo below shows the view from the inside.
The prong ...
- 377
1
vote
2
answers
2k
views
Unable to get bolt out of door
I'm unable to get the bolt out of a door. For a couple days before it was sticky, and you could push in the bolt on the inside of the door frame to functionality "reset" it so that the lock would ...
- 123
-1
votes
1
answer
797
views
Repair or installation of a mortise lock with deadbolt in an exterior door
A relative got locked out of a rental house (out of state landlord) due to a balky mortise lock in a decorative metal frame outer door. He called a locksmith to get him back in and the locksmith ...
- 22.5k
0
votes
1
answer
3k
views
Defiant Electronic Deadbolt does not retract fully
Hi I installed a Defiant Electronic Deadbolt and for the past couple weeks it is not always opening properly. What happens is the bolt goes to retracts about 1/2 way and sort of sticks. Eventually the ...
- 9
3
votes
2
answers
8k
views
How can I remove the interior side of a Kwikset handle set with "interconnect"?
I just moved into this house that came with a handle set that includes some kind of interconnect plate on the inside that serves to unlock the deadbolt when the knob is turned. I want to remove the ...
- 133
2
votes
2
answers
7k
views
Cannot adjust dropbolt on bifold doors which is catching
I have a patio door made of up two aluminium tri-folding doors which meet in the middle. One side has a normal 5 point locking system operated by a normal door handle and key. The other side has a ...
- 205
0
votes
1
answer
1k
views
What is the use the plugs over this deadbolt's bolt holes?
When re-keying our house, I came upon these unexpected bolt hole plugs in the deadbolt assembly. Is there a graceful way to remove them? I'd prefer not to take a small prying tool and force them out, ...
- 452
1
vote
2
answers
2k
views
Schlage single cylinder lockset won't release from the door
I have a nosy homeowners association that enters anytime they want....my privacy is not respected. I have purchased an identical Schlage set, have removed all the screws I can, but the covers don't ...
- 11
0
votes
3
answers
4k
views
Old mortise lock bolted from inside
I have a situation in my 90 year old house with the bathroom door. Last night my bathroom door was closed and somehow bolted locked from inside and I can't get into it or unlock it. I believe this is ...
- 125
1
vote
1
answer
4k
views
Please advise how to lubricate stiff latch bolt of mortise lockset on metal exterior security door. (NOT the pins in the keyway!)
The latch bolt of the mortise lockset in a metal security door is stiff. I worry about the long-term effect of slamming the door in order to drive the stiff latch bolt back and allow the door to ...
- 31
3
votes
7
answers
6k
views
How do I find a replacement door lock for this?
I moved into a newly built home and am trying to replace the deadbolt and the lever below.
But I'm not able to find a replacement lock that replaces my existing locks. All locks I've looked at have ...
- 145
0
votes
1
answer
1k
views
Replacing my locks/door handles
I'm going to replace the locks in my home. I'm doing this because we are renting the property out and I want to get keys that are "un-duplicatable" (the kind where only the owner is allowed to make ...
- 157
14
votes
1
answer
171k
views
How do I remove a Kwikset deadbolt with no screws on the inside plate?
My exterior door deadbolt has gotten stuck - it'll open with the lever but not the key. By spraying WD-40 inside the lock, I've been able to get it to work but it's very stiff. I'd like to remove the ...
9
votes
7
answers
85k
views
Did I break my Kwikset SmartKey lock by trying to rekey with a key that doesn't fit all the way?
I got a Kwikset deadbolt lock (has key hole on both sides instead of key hole externally with latch internally). This lock uses SmartKey technology so you can rekey the lock to use a new key rather ...
- 5,912