8

I have a condo with a concrete subfloor so I floated an engineered wood floor above it. It's not a "click-lock" floor, it's a glued T&G install.

A contractor recently did some work in the unit and damaged one of the boards. How can I replace a single board in the middle of the floor for a floating installation?

Improve this question

3 Answers 3

Reset to default
6

You'd have to treat it like a hardwood floor t&g repair:

  1. Run a circular saw down one side, staying away from seam at least the thickness of the tongue, with depth set to board thickness.
  2. Repeat #1 along the other side.
  3. Connect the top and bottom cuts across the board, either with a chisel or OMT (Oscillating multi tool).
  4. Carefully cut into corners to free the 4 border pieces, as necessary. They may just pry out.
  5. Trim the bottom half of the groove off. (I like to use a table saw and fence). You should be able to wedge it in with the tongue intact, though a small bottom bevel might assist it.
  6. Sparingly glue along edges of existing tongues and the new board edges and weight it down, as necessary.
Improve this answer
3
  • I cannot glue down, this is a floating install.
    – Matthew
    Commented Feb 27, 2013 at 19:13
  • 1
    you're not glueing down, you're reglueing the tongue and modified groove, which is why you have to weight it down, because the bottom of the groove is gone. The end result are 4 glue joints around the perimeter of the board.
    – HerrBag
    Commented Feb 27, 2013 at 19:15
  • I think I understand... Remove the bottom of the groove on the new board, clear the groove on the intact board... Insert the tongue of the new board into the existing groove on the intact board, then set and weight the top-half of the modified groove on the new board?
    – Matthew
    Commented Feb 27, 2013 at 19:19
6

The general principle is you cut the length of the board with a circular saw set to a very shallow depth, making sure to not over-run in to adjacent boards. Then you use a chisel or utility knife to cut all the way to the end. You should then be able to lift the middle of the board out. If the ends are also T&G, you might need to use a utility knife to cut the tongues.

Now for the new board: Cut the tongue off the short end. Then cut the bottom of the groove off from the opposite short end and the long side. Apply glue to the tongue and the (modified) groove. Slide the board in to place by inserting the tongued edge in to the appropriate board in the floor and rotating the board down so the (modified) groove edge fits in to place. Apply liberal pressure to the long edge, wiping up excess glue with rag wetted with warm water.

Improve this answer
2
  • Do you think the board will be stable with only a single tongue on one side of the board? What will keep it from flapping?
    – Matthew
    Commented Feb 27, 2013 at 19:13
  • 1
    The glue in the modified groove will hold the board down. Wood glue is crazy strong.
    – longneck
    Commented Feb 27, 2013 at 19:21
0

I think you guys are ignoring the fact that the original floor had glue holding all the tongues and groves together. How will the old tongue come out of the groove without damaging the adjacent board? And how will the groove on the board you take out come loose from the tongue on the adjacent board.

I have a client with the same type floor who wants individual boards replaced. I just don’t see how it can be done where the edges will ever stay together. Maybe if it was laid straight on the slab, then everything could be glued down and glued together. But with that mat underneath, the boards have a little movement.

I’m wondering if the original poster ever tried what was suggested.

Erik

Improve this answer
2
  • Welcome to Home Improvement. If you'll take the tour, you'll note that this is a Question & Answer board, not a general discussion forum. As such, we expect answers to the question to be posted in the box labeled "Answer". Since this doesn't seem to answer the question, would you please edit it into an answer? If you'll stick around, you'll quickly earn enough rep to make a comment on someone else's Q or A, which is what this is as it stands.
    – FreeMan
    Commented Aug 15, 2022 at 14:20
  • 1
    Also, step #5 in the (currently) accepted answer addresses how to deal with the tongue.
    – FreeMan
    Commented Aug 15, 2022 at 14:28

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service and acknowledge you have read our privacy policy.

Not the answer you're looking for? Browse other questions tagged or ask your own question.