30
votes
Accepted
Is oil normally this dirty after a 5-hour break-in period of a small inverter generator?
Yes.
Many engines are lubricated with a "grease" or heavy oil which is designed to stick to the machined surfaces until they are properly run for the first time.
You followed the running-in ...
11
votes
What is this component wired into a bench grinder motor?
Single phase bench grinders typically use Capacitor Start motors, which would typically use a centrifugal switch inside of it to take the starting capacitor off line once it is at speed. But because ...
10
votes
Can an occasionally squealing draft inducer motor be repaired instead of replaced?
Intermittent squealing is common for "permanently lubricated" sleeve bearings that are reaching the end of life (whoops, not so permanent after all.)
Such bearings are typically a sintered (...
9
votes
What do E and COM mean in a blower motor wiring diagram?
Probably, yes: COM usually stands for common, meaning neutral. E usually stands for Earth, meaning ground.
7
votes
Microwave turntable keeps turning with door open
If any part of the microwave keeps working with the door open, you need to assume it might be emitting microwaves with the door open. Unplug it and don't use it.
Depending on the age and make of the ...
6
votes
Accepted
converting HP to Watt
I thought there should be a time factor in this calculation
Both watt and horsepower measure power. They are the same thing, just with different units, hence the direct conversion.
You seem to be ...
5
votes
Accepted
Snow blower : 0w30 or 5w30
Most engines have several weights of oil that are allowed, typically with one of them being the recommended weight. In addition, outside temperature affects which oil weights can be used. Most manuals ...
5
votes
What type of motor is this, and how could the power be limited?
Forget it, it not gonna happen.
What you have there is a "1-hose portable air conditioner".
The fan is not the part that is making the noise. It's the A/C compressor mechanism. And there'...
5
votes
What type of motor is this, and how could the power be limited?
Your fan is multi speed, running it on a lower setting would help reduce the noise. Generally the fan is the most noisy part of an AC. The refrigeration side is engineered to operate in a given range, ...
5
votes
Garbage disposal not working: It hums, but the blade spins freely and reset button is not staying engaged
If the unit is not jammed, as you say and the unit hums but does not run, it needs to be replaced.
There is nothing reparable inside these units. You need a new one.
4
votes
What do E and COM mean in a blower motor wiring diagram?
I was assuming this was an HVAC blower, but this is actually a remote blower module for a range hood.
Installation instructions located here: Zline T95 Dual Remote Blower
The unit appears to be ...
4
votes
converting HP to Watt
As another answer already explains, horsepower and watts are two units measuring the power being used (demand) at any point in time. Watt-hours - or more typically kilowatt-hours or kWh is the common ...
4
votes
Accepted
What is the non-specified tolerance of the capacitor of my furnace's inducer motor?
Typically a non-explicitly specified capacitor or resistor is +/- 20%
Out of circuit is the only way to reliably measure the device capacitance, and you're well within tolerance on that.
3
votes
converting HP to Watt
HP is the measure of output power. The efficiency of motors is terrible, often near 50%. For instance this 1 hp motor has an input of 6.1 amps at 230 volts, which is about 1400 watts. (Just a quick ...
3
votes
Constant Motor Sound in House
If the noise does not disappear if all electric circuits (possible >1 panels/boards at different locations like garage, garden shelter, basement, attic etc.?) and the water supply are shut off,
the ...
2
votes
How to size a VFD for this Antique 5 HP Motor
It can be done with a vfd? Possibly. I would want to Meg the motor prior spending the $ for a vfd. There are also ways to do it with capacitors. And capacitors plus another 3 phase motor.
If the ...
2
votes
Accepted
Identifying replacement bearings for installed heater fan motor
The way to find different bearings is by the size bb1023 crosses to a double sealed 6.35 x22 x7 mm bearing
Mr627zz is the same id/od and 1/4” thick so it is slightly thicker and may work under 5 ...
2
votes
Accepted
How to easily fill a gas can at a modern gas pump?
I've started bringing a funnel with me when filling up gas cans at the pump.
I use the funnel to jam the filler neck sleeve / retaining ring into the on position, as if it were inserted into a modern ...
2
votes
Accepted
How to size inducer motor capacitor?
The first photo shows "1 MFD/440 VAC" on the label just next to the capacitor sign,
which is the specified value for the capacitor:
1 Micro FaraD, 440 Volt AC.
Very unlikely, but still ...
2
votes
Accepted
Inducer motor is not spinning
The problem was my control board. It had at least one burnt-out relay. After changing the board, everything started working.
Thank you.
2
votes
Why is the CAFCI breaker for my pool motor tripping?
Newer cAFCI breakers have a diagnostic feature the stores the reason for the most recent trip. I would google the instructions of that model of breaker and get it to tell you whether we're dealing ...
2
votes
Accepted
Garbage disposal not working: It hums, but the blade spins freely and reset button is not staying engaged
Seems like either the motor rotor is stuck hitting an obstruction in the housing at some point in its motion, or, more likely, the stator has shorted turns (e.g., from overheating). One would have to ...
1
vote
Microwave turntable keeps turning with door open
I agree with most others. I'm all for repairing things - but I'd be hesitant with a microwave. I understand NEFF is a European brand - based on the age I would get the manufacturer's opinion. This may ...
1
vote
Microwave turntable keeps turning with door open
As already noted, this is a potentially dangerous situation. Nothing should be active on a microwave oven when the door is open except the light and the control panel. Turntable, fan or any humming ...
1
vote
Microwave turntable keeps turning with door open
This answer is based on actual events:
Recently had a minor problem with a micro that was under warranty. (less than 6 month old) The manufacturer opted to send me a new unit rather than send a tech ...
1
vote
Microwave turntable keeps turning with door open
Any ideas what’s wrong with it
Clearly the circuit, switch, or sensor that controls the turntable is malfunctioning and needs to be repaired or replaced. It could be a simple as a broken switch or ...
1
vote
3-Speed Kitchen Fan Wiring Problem
Totally honest option:
Buy a new replacement switch of exactly the same model.
Install the new switch.
Questionable but justifiable option:
Buy a new replacement switch of exactly the same model. ...
1
vote
How to easily fill a gas can at a modern gas pump?
I've never had a problem filling up gas cans, whether new plastic ones or old steel ones.
Note that the pump is designed to shut off if those little holes in the narrow end of the nozzle are covered ...
1
vote
How to easily fill a gas can at a modern gas pump?
I've never had this issue. I would suggest a different gas station and not putting the gas pump all the way into the can because it might be sensing (lack of) air flow?
1
vote
How to size inducer motor capacitor?
As was previously mentioned,the “1.0 uF” on the capacitor means the same thing as 1 MFD. The "1 MFD" is listed right on the name plate of the motor so I'd have to assume it's what the motor ...
Only top scored, non community-wiki answers of a minimum length are eligible
Related Tags
motor × 48blower × 10
hvac × 9
furnace × 8
wiring × 7
electrical × 5
electric-motor × 4
capacitor × 4
switch × 3
fans × 3
repair × 2
pump × 2
noise × 2
maintenance × 2
plumbing × 1
electrical-panel × 1
circuit-breaker × 1
gfci × 1
heating × 1
air-conditioning × 1
drain × 1
gas × 1
dryer × 1
drill × 1
drainage × 1