Questions tagged [woodworking]

Questions related to making things out of wood.

Filter by
Sorted by
Tagged with
1
vote
3answers
31 views

How to hang wood letters

I have cut out a word made of 1/2" poplar and would like to hang it in the wall. I originally thought of using my (non plunge) router with a keyhole bit to cut two keyholes, but I'm afraid that the ...
2
votes
2answers
56 views

Hold several 2x4s together for tabletop?

I was thinking of making a very rudimentary TV stand with several treated 2x4s I have here. The tabletop would look like this. What can I do to hold all these 2x4s together so that they're sturdy? I ...
7
votes
8answers
4k views

How large should a hole be for a bolt to go through?

I am building a table and I have something like the following: I want to know if I have a 3/8 inch bolt, how large should the hole on the diagonal piece be? I already secured it on the table leg.
0
votes
1answer
96 views

Will my raised flower bed design be sturdy enough?

I am building a 4'x 8' flower bed. The bed is 32" tall with a floor made out of 1x4" cedar four feet across. Soil depth is 12 inches, 32 cubic feet (8x4). Worst case 7.481 gallons per sq foot x 8 ...
0
votes
1answer
45 views

DeWalt 743 flipover saw

I have a DeWalt 743 flipover saw, the blade stopped turning for no reason. It was working fine yesterday morning, but when I came back from a break, the blade refused to turn. I can hear the noise, ...
0
votes
1answer
74 views

What is the mechanism of action of PVA glue?

The general wisdom is that wood glue sets harder than the original wood, but experiences and testimonies on this seem to vary. Two weeks ago, I replaced some worn hinge screws on a heavy interior ...
1
vote
4answers
85 views

Slightly extending an opening in plywood

I'm trying to fit a slightly larger trash can into an opening in thick (about 1") plywood (see photo). Basically, I need to shave off some material in the corners to make the new can fit. Question is,...
1
vote
2answers
55 views

Weight load for a bench using 2 x 12

I would like to build a entryway bench using a 3 foot length of 2 x 12. I plan to use 16" hairpin legs made of 1/2" cold rolled steel. Not sure if the type of wood matters, but I will probably use ...
2
votes
0answers
70 views

Do hinge screws become more tight-fitting over time once installed?

I've noted newly installed hinge screws can be replaced more easily if replacement is within days after fitting. If left for weeks or more, they become considerably harder to remove due to friction. ...
1
vote
1answer
56 views

Can water-based wood glue deep in timber joinery initiate wood rot?

In joinery projects where PVA glue is restricted access to air (for example, with doweling) moisture is dissipated through the surrounding wood and the glue typically takes longer to dry. Is there ...
1
vote
2answers
99 views

Is this loft bed flooring strong enough?

I'm about to construct a loft bed as in picture: it's 240cm long and 180cm wide (7.9ft x 5.9ft). The floor frame is composed of 2 main beams (2x6) that run on the longitudinal direction, and 7 joists ...
1
vote
1answer
49 views

Risk of overtorquing wood screws with T-handle screwdrivers?

The screws in question are 4.5 x 30mm A2 stainless steel hinge screws. As far as I can tell, they are good quality, branded (TIMco), double-countersunk, manufactured by thread rolling. Material is ...
2
votes
2answers
36 views

Paint/stain used for wooden planter?

I built a large planter using untreated wood. Before pouring the potting soil into the planter, I have to paint the the planter with something that will protect it from the soil, the humidity, etc. I ...
0
votes
0answers
39 views

Best half-decade for a used well-maintained Unisaw?

I'm in the market for a used Unisaw. I found that well-maintained Unisaws on craigslist vary from about $800 for an 1980s model to about $1100 for a 2010s model. So there's actually very little ...
0
votes
1answer
30 views

how to strongly secure a wire over a couch frame to stretch seat spring webbing

I have a wire piping that used to be secure around the frame perimeter of my couch base so that a flexolator webbing with springs would be stretched taut and clip onto it. However, this piping has ...
1
vote
1answer
64 views

How do I go about leveling out streak marks in my wood stain?

I used knotty alder wood and sanded to 320 with a random orbital sander. Knotty Alder Min-Wax Pre-Stain Conditioner Min-Wax Oil-Based Stain Applied with t-shirt rag I see streak marks in my staining ...
0
votes
1answer
38 views

What’s is the consequence of trimming too much of a wood door?

I’d like to have all matching doors downstairs in our house (link), but one of our door frames is shorter than all the others. The doors say the maximum you can trim off any given side is 5 mm, but I ...
15
votes
8answers
3k views

Wood glue versus epoxy for doweling stripped screw holes

I've come across two schools of thought for gluing dowels in place. PVA wood glue, such as Titebond. Two-part epoxy, such as Araldite. Bearing in mind long-term stability, which is preferable for ...
0
votes
2answers
120 views

Dismantling an old piano

I'm trying to dismantle an old piano, and I would like to do it without damaging the individual parts or pieces of timber (for sentimental reasons - may use it in other projects). I've screwed out ...
4
votes
6answers
992 views

Cutting a 4.5m long 2x6 in half with a circular saw

My question is about cutting 2x6 boards in half with a circular saw ("Skil"-saw). Now, I've looked around, and there are many sites describing how to cut off a small piece from a larger piece, the ...
7
votes
3answers
1k views

How to cut a perfect shape out of 4cm oak?

I need to mount an undermount copper sink to our new kitchen surface. The surface is 4cm oak, which will be varnished with 12 coats of marine lacquer to protect the oak from water. What I want to ...
0
votes
4answers
135 views

How much weight can a 2 by 4 support in this configuration?

I'm using dimensional lumber ( whitewood ) from Home Depot. https://www.homedepot.com/b/Lumber-Composites-Dimensional-Lumber/N-5yc1vZc3tc It is just a 4 foot by 8 foot rectangle with a center ...
-1
votes
1answer
84 views

How much weight will this structure hold? [closed]

I'm going to build this structure as is. This question is not the same as my earlier post as I am not seeking any more design advice as in the previous. I will not make any more changes to it. My ...
0
votes
2answers
90 views

How to transfer lumber cut with odd angles

I am interested in learning this craftsmanship /technique: Look like the piece of lumber in between has perfect cut to match the angles. How did they transfer the cut dimension? Is there a tool for ...
0
votes
1answer
43 views

Replace rear bearing of Dewalt DWS520 Type 1 track saw

I would like to replace the rear bearing from a Dewalt DWS520 Type 1. I am not getting the armature removed. I did remove the yellow cover, but the armature is still stuck in the body of the saw. Can ...
0
votes
1answer
71 views

Can 1" thick planks take (vertical) shear loads of 200kg through bolts without splitting?

I am extending an aluminium ladder by bolting the lower ends to 3" wide, 1" thick struts. I am concerned that the (6mm) bolts may split the wood when loaded.
1
vote
1answer
27 views

Does water based polyurethane affect the color of paint?

I recently painted a dresser. I originally painted it a darker gray than I wanted so after putting the initial two coats on I took the paint back to Home Depot and had them lighten the rest of the ...
0
votes
2answers
161 views

Attach 2x4 to another 2x4?

This is yet another 2"x4" question. What's the best way to attach a 2"x4" to another 2"x4" that's resting over it? The rail is a 2x4 and it will be held, on each side, by two 4x4. Under the 2x4 rail ...
22
votes
5answers
68k views

How would I go about turning a tree in to a tabletop?

My father-in-law is about to cut down a large Ash tree (on the insistence of a neighbour). At the same time, we need a dining table, and quite like the idea of a simple wooden slab on legs. ...
1
vote
2answers
2k views

Is it safe to use stain and polyurethane on a wooden trivet

I'm making wooden trivets (using hard woods) to sell. I would like to use stain & polyurethane but I'm not sure if it will melt or become damaged when a hot pan is placed on it. Will it be safe?
1
vote
1answer
77 views

What is the proper way to sand live edge piece of wood in preparation for a polyurethane finish?

I have debarked a live edge walnut slab. Since the edge is rough and not flat, how would one properly sand that live edge without killing all of the subtle contours of that live edge. All of the ...
0
votes
0answers
27 views

Wood rot treatment product

A few years ago I removed all the soft wood on a windowsill & rebuilt the sill with new wood and filler. I've just found out that it's rotten again. 1) Should I have treated the old wood prior to ...
0
votes
0answers
62 views

Sagging cubby/shelf solution

My cabinet vendor installed a really cool 5 sided, 12" deep cubby(shelf) below my upper cabinets. It's laminated 3/4" plywood. The problem is that it's 84 inches long and there already is a very ...
0
votes
0answers
28 views

How to drill into a 5/8” edge?

I’m trying to follow these following day bed plans: https://www.ana-white.com/woodworking-projects/simple-daybed and I’m trying to attach the bed frame to the posts. It looks to call for screwing the ...
0
votes
0answers
62 views

Finishing garage for year-round woodworking workshop

In Toronto, ON and I'm finishing my attached double garage (20x20) in hopes of setting up a woodworking shop. It's not currently heated or cooled but I plan on using it year-round so heating is ...
1
vote
1answer
4k views

Can you create wood conditioner from DIY wood sealant?

I'm working on staining an old bookshelf, and I've worked on creating my own DIY wood stain and sealant (save money + no VOCs + Feels good). I created my own wood stain already by using steel wool and ...
2
votes
6answers
315 views

Wood glue to reinforce screw holes in an oak frame?

This is for load-bearing bronze screws in an oak frame, carrying a heavy oak door. Four of the screws were removed momentarily for maintenance work. Two of the screw holes may have been stripped ...
3
votes
3answers
74 views

How can I change chair straw backing?

I have this chair with a straw backing. I would like to change the straw on my own since the places that do this work charge over $200. Is this something I can do on my own? If so, how can I search ...
6
votes
5answers
646 views

Replacing tongue and groove floorboards: but can't find a match

A room in an old farmhouse, formerly a porch, now enclosed, has floors made of tongue and groove lumber. I need to repair those floors by replacing at least some sections of floorboards - somewhere ...
4
votes
2answers
244 views

Router safety - what did I do wrong?

Long story short I was running my DeWalt fixed base router (8000-24000 RPM) on a piece of work when it started making a funny noise. I lifted the router up to see why it was making the noise, and ...
1
vote
2answers
50 views

Hanging floating shelving

I am making similar shelving to these and I am trying to figure out the best method to hang these shelving. Any suggestions?
2
votes
1answer
926 views

Why did my third coat of polyurethane finish “buckle”?

I'm refinishing a table I built about 10 years ago. I put 2 layers of gloss polyurethane down and sanded between coats. All was fine at this point. I gave it another light sanding and put a third ...
2
votes
1answer
143 views

Can I use a 16 gauge nail gun for framing lumber?

Can I safely use a Bostich 16 gauge nail gun to toenail stud grade 2x4s? The nail head is stationary at 90 degrees. The project: bay window seating. Issue: front rail & plate supported by ...
9
votes
7answers
206k views

How do I remove excess wood stain that dried before I could wipe it off?

While staining some wood, we had an emergency and had to leave. The stain has now dried and I'm not sure how to remove the excess; it's normally wiped off before it dries. When I get home I'm going ...
0
votes
1answer
67 views

There is any simple way to forming handmade paper pulp? [closed]

I want to know how can I make a form for forming handmade paper pulp for something like paper egg container. There is possible to make small hand press from for example wood/steel and pressing that ...
0
votes
2answers
69 views

What I can use to waterproof a sink cutout

I'm using solid wood to make a worktop/countertop in my camper van. It's going to have an undermounted sink, so I need to use something to protect the edge of the sink cutout from water. I have no ...
3
votes
1answer
357 views

Can i use larger/smaller circular saw blades on my circular / plunge / table / miter saw?

I own a plunge saw and a miter saw. Can I use blades from one saw on the other saw?
1
vote
1answer
41 views

how to repair bi-fold door with fallen slats?

A piece of this bi-fold closet door has warped, and as a result many of the slats have pulled out of one or both of their end-points. It seems like it should be possible to repair this with clamps, ...
0
votes
1answer
31 views

Refinishing Outdoor Wood Table

About 3 years ago I built an outdoor patio table from home depot pressure treated lumber. I walnut stained it and applied 3 layers of Helmsman spar urethane. It looks like the sun/rain has worn down ...
0
votes
0answers
43 views

Polyurethane shows oil when touched?

I finished a set of pine 2x12's that will be shelves for a bookshelf using the following process. Sanded the boards with 80, 120, and 220 grit Stained the boards with Minwax oil-based Early American ...