We’re rewarding the question askers & reputations are being recalculated! Read more.

Questions tagged [trim]

Trim provides a transition between different surfaces and materials, covers gaps and adds a finished look. Trim includes molding (moulding), wainscoting, mantels, etc.

Filter by
Sorted by
Tagged with
0
votes
1answer
70 views

How to properly scribe molding?

I have a 96" wall. The wall and ceiling are not square. I wanted molding on the top. I leveled and secured the molding. The left side of the molding was up against the ceiling. The right side of ...
2
votes
1answer
2k views

Best way to hide tile edge *and* hardie board edge?

My googlefu may be off, but I cannot find what I'm looking for... I'm installing a backsplash using 3/8 inch thick marble. The tile will be set on 1/4 inch backer board (didn't want to demo to the ...
4
votes
3answers
29k views

Can I use glue instead of nails to install shoe molding?

I installed engineered bamboo flooring in my home office and have quarter round shoe molding to install to cover the expansion gap. Given how hard the trim is (I've bent nails installing the carpet ...
8
votes
2answers
5k views

At what height should I install chair rail? [closed]

I have a couple questions regarding my chair rail installation. I have read that, if possible, the chair rail should be at the same level as the window sill but I am thinking it might be better a ...
1
vote
1answer
170 views

Cut steel fascia board cover lengthwise?

I am wrapping a porch beam with white steel fascia board cover. The height of the space I need to cover is about an inch less than what the fascia board cover is. So I need to basically cut an inch ...
2
votes
1answer
305 views

What type of wood is suitable for fascia?

I'm replacing some fascia boards, I am looking for something that is rot-resistant but I am hesitant to use pressure treated lumber due to shrinkage as it dries out and I don't want gaps (project has ...
2
votes
1answer
46 views

How to cover the crevice between some laminate and molding

There's a small (SMALL!) walkway next to this staircase that was originally covered with carpet. It's been ripped out and replaced with laminate, but now there's a crevice between the laminate and ...
0
votes
1answer
114 views

Should this elevated door have trim/casing at the bottom?

This door separates a sunken rec room from a den. It has always struck me as odd that there is trim/casing along the bottom. Is there a better way of handling the trim around the sides, but with no ...
1
vote
1answer
409 views

How do I stop water from wicking into the wall?

I just bought a new home, and water is getting into one corner of the house. The drywall on the inside of the pictured corner is soft and there was mold under the baseboard, but no water marks are ...
1
vote
1answer
142 views

How to finish pine woodwork/trim

we are renovating a 1905 Victorian. I stripped and stained the downstairs woodwork/trim (oak) and headed up stairs to work on the trim/woodwork (baseboards, window/door trim/doors) only to find that ...
1
vote
1answer
42 views

What to use between tiles and door?

I'm seeing this sort of interface where grout has been placed between the wall tiles and the door jamb. Is that the best material to use? Why not silicone? And how about aluminium angle trim? Or is ...
16
votes
6answers
4k views

Why is all this exterior trim rotting and how do I fix it?

We realized there was some rot on the exterior of the house when we bought it two years ago, and I knew obviously I would want to deal with it eventually. As I've been looking more around the outside ...
1
vote
1answer
2k views

Can I make PVC pipe into a decent indoor column?

I have a beam between the living room and dining room which is load bearing. We've already placed the laminate around the base, so I'm not entertaining further ideas of moving the posts. I'd like to ...
13
votes
5answers
96k views

How do I install transition molding between my new hardwood and existing tile floors?

I have ripped out some old carpet and am preparing to install a new solid hardwood floor myself. In several places, the floor transitions to an existing tile floor. The hardwood floor guys told me ...
0
votes
3answers
56 views

How do you deal with the cut edges of window trim?

I have put up more than my share of trim. But I was wondering if there was an easier way (so I will leave mine out to not influence answers) to do the but edges. Basically in the example below ...
1
vote
3answers
415 views

How can I trim out a supply pipe passing through a tile floor against the toilet base?

I need a recommendation for a product that I can use to hide where this pipe meets the floor in my bathroom. There was a metal piece here but I had to cut it off since the new toilet comes so close ...
1
vote
1answer
33 views

Suggestions for improving these stairs

I love the treads on these stairs which I will be revitalizing. The risers are awful. I was thinking of adding a nose and then using 1/4 be needed plywood to cover the treads. The wall right next to ...
1
vote
1answer
88 views

What's the best way to repair or replace window sill & apron that's been sawed off?

The previous homeowner installed built-in armoire cabinets and bookcases that I plan to remove. In order to facilitate the opening of the armoire cabinet door, they cut into the window sill and apron ...
0
votes
1answer
24 views

Replacing trim set in horse hair plaster

There are a few places in my house where I would like to replace the door trim, but the walls are horse hair plaster. Is there anyway to do this without having the plaster totally fall apart?
0
votes
1answer
55 views

What are the options for my window on my brick house?

I was hoping to get some guidance and am including a picture. I have a brick house that was built in 1913 and then gut rehabbed in 1998. They replaced all of the windows and redid everything in the ...
2
votes
1answer
122 views

Is it a problem to have gaps in the drywall hidden by molding?

We recently had someone repairing the stairs in our home. During the process of removing the old stairs they created these gaps in the drywall (see images), however, they never filled them and simply ...
1
vote
1answer
30 views

How accurate does corner angle measurement on crown moulding need to be?

How accurate does angle measurement on crown moulding corners actually have to be? What I am saying is say compare a manual angle finder that has 1 degree increments vs a typical digital one that ...
5
votes
9answers
86k views

What height to set baseboards before carpet is installed?

I am wondering how high I should space my baseboard off the floor before carpet. I know the tack strip will go next to the base and then carpet goes over it and tucks under the base.
0
votes
0answers
185 views

Nominal size (shrinkage) for 3 x 12 porcelain tile bullnose trim?

What is the range of acceptable shrinkage for porcelain tile trim? The trim is advertised at the supplier site as 3" x 12"; the actual trim is 2 5/8" x 11 3/4". I did some online research before ...
1
vote
0answers
91 views

Reattaching loose trim

I have some outside door trim that has come loose. Below are two pictures showing the difference between the top and bottom of the trim. I looked at this thread but it was not very helpful as the ...
0
votes
2answers
1k views

How to install crown molding or valance board around a cabinet?

I am replacing the cabinets in my kitchen and am going to be installing some crown molding (actually a valance board and then crown molding) around the top of the cabinets, as in this picture. The ...
2
votes
1answer
2k views

How to fill 3/4" gap between tub and tile floor

My house is 120 years old and there are very few level surfaces or right angles. I just had the (alcove) tub and shower replaced. One end of the tub apron is nearly flush with the floor, but the ...
0
votes
1answer
38 views

Securing two sections of 'floating' molding together and to wall

There is no wall stud behind the ends of these two sections of molding. (Otherwise, of course, I would use nails.) The surface behind them is painted gypsum wall board. The molding on the right is ...
0
votes
1answer
435 views

Is this mold, mildew or just dirt?

We just removed some molding from our floor only to reveal some kind of black substance that looks like dirt. We are not sure what it is. See the following photograph.
3
votes
1answer
1k views

Exterior Window Casing in Brick Exterior

So I was attempting to install new exterior window casing on my windows due to the existing casing/trim peeling and seemingly rotting. The exterior of the home is brick so I bought some 1 1/4" x 2" ...
2
votes
4answers
172 views

How to trim a cut on a hollow core tabletop edge?

I have a hollow core tabletop, which is too wide for where it will go. I'd like to cut it into two pieces. What is a good way to finish the cut edge? Or is it just easier not to bother and get a ...
0
votes
2answers
701 views

What to do with gap between cut baseboard/shoe moulding and new wider door trim

I put in new door moulding around a door. The new moulding was a little bigger than older moulding which resulted in my cutting the baseboard/shoe moulding with oscillating saw. I am left with a small ...
1
vote
1answer
400 views

Airbrush-size airless sprayer for painting interior trim?

I have a lot of detailed interior trim to paint with latex enamel paint. It’s a pain to paint with brushes or small rollers and it seems like it would be so much easier to use a very small airless ...
2
votes
1answer
3k views

How do I determine the correct tile trim depth?

I'm installing some large format (406mm x 406mm) 12mm travertine tiles on some walls in a bathroom. I'd like to finish some exposed tile edges within some aluminium tile trim. However, I'm unsure ...
4
votes
2answers
9k views

What are the differences between wood and composite shoe molding?

I'm about to install shoe molding all over my house. I'm deciding between composite (I think it's PVC) and wood. They are quite similar in price. How do these 2 materials compare in terms of: ...
4
votes
2answers
358 views

What kind of trim should I use for an aluminum backsplash behind a stove?

I would like to use metal trim for the aluminum backsplash behind the stove; the trim would go between the backsplash and the cabinet and tile. What kind of trim would you recommend and what is the ...
0
votes
1answer
174 views

How can I transition between these floors at differing levels?

I need some ideas for the transition trim. I don't want it too tall. I have kids and don't want them to trip over it.
2
votes
1answer
4k views

Door frame pulling away from wall

over time the molding around the door frame has pulled out a little and we always just use a hammer and block of wood to put it back into place, but recently my door was slammed and now it's ...
1
vote
3answers
138 views

Is MDF a reliable product for interior trimwork?

We are debating whether to use MDF or real wood for interior trim around doors and windows. We're told that the MDF is easier to work with ~ no sanding and possibly cheaper. However, we have gotten ...
0
votes
1answer
415 views

Crack in joint between molding and ceiling

I have a very old house with plaster walls. After getting a new roof, a large crack opened up between the molding and the ceiling where the wall is pulling away, but only along the one outside wall. ...
0
votes
1answer
560 views

Older style door trim

I am doing renovations on the inside of my really old house, and am looking to update my interior doors. I have the old style door trim and doors (skeleton key door locks), and the really old door ...
1
vote
2answers
76 views

How do I fix my trim that wasn’t sanded well

Trim that was painted was not sanded well and now we have bumps on the painted trim, how do I fix this?!
1
vote
1answer
60 views

What does the “thickness” measurement in a t molding measurement actually describe?

I'm trying to buy t-molding online for hardwood that is 1/2" from subfloor to top of the hardwood, so I would like a t-molding that is 1/2" from the bottom to where the t-molding would rest on the ...
0
votes
3answers
2k views

Uneven ceiling, best way to fix it?

Contractor responsible for preparing the ceiling and painting, neglected to mention the ceiling for bathroom is visibly uneven. 7cm difference from one end to the other. Looks also a bit concave. The ...
2
votes
5answers
8k views

How to cut 45 angles in quarter round shoe molding with circular saw?

I do not own a mitre saw, which seems like the best tool for cutting skinny quarter round shoe moulding at 45 degree angles. While I can manipulate the angle on my circular saw, which worked very ...
4
votes
4answers
55k views

How do I fix a Bostitch nail gun that is jammed?

I have a Bostitch nail gun (pneumatic) and it has been working fine all day until about 30 minutes ago. I went to nail in a piece of molding, and when I pulled the trigger I heard air feed into ...
7
votes
9answers
158k views

What is the best way to fill finishing nail holes on door and floor trim?

There have been a couple of similar questions but none for my exact usage or that provides a good answer. I consider myself average to weak on finishing wood work so would like to hear some good ...
2
votes
2answers
9k views

How can I repair scratches on door molding?

I live in an apartment with my cat. Through the use of a water bottle, I've gotten him to stop, but he's left quite a few deep scratches and gouges in the molding around some of the internal doors. ...