Questions tagged [table-saw]
The table-saw tag has no usage guidance.
36
questions
0
votes
1
answer
81
views
How can I remove super glue from a table saw deck?
Apparently some super glue has spilled on the table of my table saw. Quite a large amount. The table appears to be a hard plastic, its a Dewalt 8" saw.
Is there anyway to get this off without ...
0
votes
0
answers
40
views
Bowed Edge from Table Saw
It has been a while since I've used my table saw, so, while I once new my way around it pretty well, I'm rusty now.
I started with a 40 inch long by 15 inch wide sheet of 18 mm Baltic Birch. I set my ...
7
votes
4
answers
3k
views
Has anyone seen kickback occur on a wet table saw for tile?
Most people are familiar with how table saws can kickback when pushing wood through it. I'm talking about a wet table saw with the blade that is housed below the table and protrudes up (as opposed to ...
1
vote
1
answer
630
views
AFCI breaker trips on the second start of table/miter saw
I recently purchased a new table saw and miter saw and they are tripping my AFCI breakers. Curiously, each saw starts up and runs fine the first time I try it and I can stop it without tripping the ...
0
votes
3
answers
518
views
Can I cut carpet tiles with a table saw?
I don't find any specific blades, however no explicit recommendation not to cut short pile carpet tiles with a table saw. That's however no base to assume that I should try it.
For starters, I'm not ...
1
vote
1
answer
458
views
Is it ok to store a table saw outdoors in a crate?
I recently purchased my first table saw - a Ridgid R4518 or similar model number. My only 'indoor' storage space is a small side shed that houses my water heater - it's very difficult to get the saw ...
16
votes
4
answers
10k
views
Can I run a 15A table saw on a 15A circuit if there are also shop lights on the same circuit?
I apologize if this is a tired question, but none of the other similar questions I found are close enough to what I really need to know.
I am hoping to buy a DeWalt table saw for use in my garage. The ...
6
votes
4
answers
1k
views
Tabletop saw stops midway through chipboard
I am new to woodworking and I tried my ''new'' secondhand table saw (General LR63420 Model D) today. It cut through the first few chipboard boards just fine but then had a lot of trouble going through ...
1
vote
1
answer
831
views
Why is my tablesaw whining?
I have a Craftsman 113.298031 tablesaw. Recently it has started making a whining sound and the blade is easily bogged down. Previously the blade bogged down without the noise and I had to tighten ...
1
vote
3
answers
1k
views
Put table saw table on wheels
I would like to put this table on 2 wheels so I can wheel it around and move it outside to my patio.
I have these but not sure how to mount them on the legs.
Edit: Thanks for the suggestions, here's ...
1
vote
0
answers
75
views
Stand for 10" table saw
This is NOT a request for a recommendation for any product.
I need a stand for my 10" table saw.
The company that made mine no longer sells parts for it.
I am willing to make a stand and having ...
1
vote
1
answer
317
views
Table saw blade stops on contact with wood whilst motor keeps running
Table saw blades spins fast, but stops on contact with wood whilst motor keeps running so cant saw wood
Its Rexon Model RM130, 1.6kW, RPM 4800 had not been used for some years
I have sharpened the ...
0
votes
0
answers
71
views
table saw -- install release lever
A question to those who use Mastercraft 10" Table saw, Model 055-6755-8. I just got the used one (but in good shape) from someone, and the riving knife wasn't installed (I do have it though), moreover ...
3
votes
4
answers
1k
views
Are loose teeth in a saw blade a safety concern?
When I watch videos on using a table saw safely, it almost always is about kickback.
I realize, that kickback is the most dangerous hazard, but are loose teeth, that could become projectiles, when ...
2
votes
2
answers
311
views
What's wrong with my table saw?
(I asked Should I sharpen or replace my table saw blade? and got a good answer. (Paraphrased: sharpen $100 blades, replace $30 blades.) But, as it turns out, I was suffering from superstitious ...
2
votes
1
answer
334
views
Should I sharpen or replace my table saw blade? [closed]
I got my table saw second hand several years ago. It came with a general purpose blade which has served me well without cleaning or sharpening until recently. I made what I now realize is a mistake ...
1
vote
2
answers
301
views
Cut acrylic with table saw?
Can you cut acrylic with a table saw (universal wood blade)? Or is this a very bad idea, as it will badly melt the acrylic and make a mess of everything; or dull the blade or something like that?
18
votes
4
answers
18k
views
Why is my table saw blade burning oak boards as I make rip cuts?
Bought a new saw blade, most expensive one I've seen and it still burns the wood and takes some pushing to get through.
I am ripping 1 3/4 thick oak with the grain.
Blade is Orange Chrome Heavy Duty ...
1
vote
1
answer
1k
views
Did I blow the motor of my table saw?
Cutting some cedar and overworking my Dewalt 10" portable table saw and it slowed down and then shut off. I let it cool for hours, cleaned it of dust and debris, tried another outlet and it has not ...
2
votes
1
answer
408
views
How should I cut non standard angles, shapes and miters?
I want to make a doll house for my daughter.
I want to copy a "lighthouse" dollhouse I saw in a glass case.
It is half a decagon (5 sides) in shape. Open at the back for play. It is about 3 feet ...
1
vote
1
answer
62
views
How can I fit a board to another that isn't straight?
When I created this end cap I knew the floor was not level, but I only have the straight cut of my table saw.
See the gap at the lower left?
For future projects....
How could I have cut this so I ...
1
vote
1
answer
195
views
Why are the front and rear slide rails offset on my Craftsman table saw?
I've got a couple of questions regarding a Craftsman table saw (Model 315.228510) that I own.
When attaching front rail, it said to match the 6-7/8 mark on right scale to right edge of saw base. The ...
0
votes
1
answer
336
views
Buy a table saw or circular saw
At the moment I'm considering my next power tool purchase. I'm a home improvement beginner and have been enjoying the journey, and I'm now ready to get serious about investing into a proper saw. I ...
1
vote
1
answer
65
views
Would these 3 motors perform differently?
I've three older, used, 1 hp, 3450 rpm, Sears/Crafstman motors to choose from to run a used 10" table saw on a 110v power. None smell burnt.
If they are all in equivalent decent shape, will they ...
0
votes
1
answer
400
views
Cutting slots in delrin on table saw
I have a table saw that can accommodate a 3/8" dado stack.
I need to cut 3/4" wide x 3/8" deep dados in a 3/4" thick delrin sheet. The table saw is the only tool I have that can really do something ...
0
votes
1
answer
601
views
Craftsman 137.248760 tablesaw blade comes loose
I have a Craftsman 137.248760 table saw that has recently started giving me problems. When I run the saw, the blade appears to loosen and continues to spin freely on the arbor after I turn the saw off....
0
votes
2
answers
116
views
Removing angled section from edge of board?
I have a 1" thick sheet (maybe plywood or solid wood or MDF) and I would like to cut a section out of the edge. This image shows the board, in green, in cross section:
The angle is 30/60 degrees. I'm ...
1
vote
3
answers
15k
views
How to cut a 4x4 fence post lengthwise and at an angle?
I need to make lengthwise cuts down the entire length of an 8 foot long 4"x4" fence post like so:
In that diagram the blue lines represent the cuts I need to make, and the purple areas are the areas ...
3
votes
5
answers
4k
views
How do I cut lengths of wooden beading lengthwise?
I wish to replace some missing beading in a stairwell. I've only a limited amount of equipment and experience, but I figured I could get a mitre saw and some matching wooden edging and the right stain,...
1
vote
4
answers
5k
views
Why does the blade of my table saw stop?
I have a cheap, old (but, until recently, serviceable) belt-drive, table-top table saw, Skil 10" model 3400.
Last week while cutting a 2x4, the blade stopped but the motor kept going. I finished up ...
1
vote
1
answer
640
views
Is it possible to get a magnetic mount to attach to my aluminum tablesaw base?
I want to use a magnetic base and precision deflection meter with my tablesaw, which has aluminum instead of cast iron table, which means it is not a magnet-friendly material. I'm wondering if anyone ...
1
vote
3
answers
11k
views
How can I cut aluminum angle stock without damaging my tools?
How can I cut aluminum angle stock without damaging my tools? I've done some looking around the interwebs and have not found anything definitive - basically there are warnings about cutting it with ...
1
vote
1
answer
1k
views
What can I do about a dead Delta 62-043 table saw motor?
I bought a used Delta 62-043 table saw for $200 about a year ago. It sat in my shed for a while, and I just now turned it on to start a project.
There was some black smoke. I'm embarrassed; I thought ...
9
votes
3
answers
2k
views
Why do some table saws have a direct and a reverse ruler on the fence?
For example, in the ruler, the bottom row goes from 0 to 31 cm from left to right and the upper row goes from 32 upwards from right to left?
EDIT: Here is the manual for the tablesaw pictured above. ...
1
vote
1
answer
2k
views
Can I mount a router to the Ridgid R4510 table saw?
I'd like to purchase a Ridgid R4510 table saw, but I want to make sure I can mount a router under it. Should I be concerned with whether this specific table saw is going to allow it or do pretty much ...
9
votes
2
answers
25k
views
Can I use an 8" dado blade set in a 10" table saw?
I have a 10" table saw... this is probably a stupid question, but can I use an 8" dado blade set in this saw? Is one only supposed to use 10" blades in a 10-inch saw? I read on some contractor's ...