Questions tagged [studs]

Vertical member in wall framing.

Filter by
Sorted by
Tagged with
1
vote
1answer
909 views

patching hole to be reused

I'm trying to mount a tv into my chimney walls. My TV is 65" and weighs in about 65"lbs or so. I drilled in 6 holes. 3 at the top 3 at the bottom with about 12" apart. I was going to use the strap ...
0
votes
1answer
644 views

How to frame steel studs parallel to concrete ceiling “joists”

One of the drywall I need to hang runs parallel to the joists (concrete joists and slab above it), and I'm at lost on how to affix the upper tracks which would be between two joists. I've seen this ...
4
votes
3answers
2k views

Is it OK to install a TV mount when it can't be attached to a stud at all mount points?

I have a TV wall panel that can only reach two studs. I was wondering if it's fine to screw the left side and the center on studs, and have the right side anchored in the drywall. My TV is 30lbs with ...
2
votes
1answer
14k views

Will using concrete anchors in wall studs cause problems?

While installing a wall mount for a 48" TV, I realized I made a mistake. I drilled a ⅜ pilot hole in the wall stud and then installed the anchors provided with the mount that the lag bolts would be ...
1
vote
1answer
258 views

How to fill an old window alcove?

In one of the bedrooms in my house (1930s), there is a sunken alcove where an old window used to be, the internal sill is still there. Whoever bricked up the window used bricks much thinner than the ...
0
votes
1answer
77 views

Electrical across studs in basement?

I have a small workshop that I need to add an outlet for. There's a light switch 2 studs away that I'll use for power. I have no plans to drywall this area of the workshop. Is it ok (against any ...
1
vote
0answers
533 views

Ceiling fan install - orientation of mounting bracket to slope of ceiling

I'm replacing a light fixture with a fan/light using a down rod mount on an angled ceiling. The frame studs run parallel with the slope of the ceiling. Manufacturer notes to install mounting bracket ...
2
votes
1answer
993 views

How should I build a low profile stud wall in a basement?

I'm considering several options for building out a wall in a basement. Unfortunately, due to the way that the stairs leading to the basement are positioned in my house and the spacing I have to build ...
1
vote
0answers
142 views

How should I build stud walls to make shelves in a room that has a sloping ceiling and floor?

We have a home that is 104 years old. There is a room that was added in the 1940's and built over a sloped roof from the rooms below. It is fully enclosed and we would like to add some shelving in the ...
5
votes
2answers
3k views

how critical are distances between studs?

I'm in the process of finishing my basement (east-central Minnesota, US). So far, I've put up a couple of wood stud walls... non-load bearing, simple partition walls. One one of these walls, the ...
1
vote
0answers
1k views

how to attach threaded rod to wall stud on hinge

How can I attach threaded rod to a wall stud so that it is on a hinge. The hinge axle will be horizontal so the rod can rotate up and down but not side to side. The one piece solution I have found ...
0
votes
2answers
131 views

polystyrene insulation over dryloc basement walls

I am a DIY beginner. If I am installing polystyrene over drylocked basement walls, do I need a vapor barrier? Do I put the studs on top of the polystyrene? So, from exterior to interior it would be:...
2
votes
3answers
1k views

replace stud that has vent pipe through it

I had some water damage in my bathroom and a few of the studs are rotted. I am assuming they need to be replaced. The problem is these studs have a plumbing vent pipe drilled through the middle of ...
2
votes
3answers
2k views

Is it safe to shave off 1/8" from a load-bearing stud?

I am trying to install a small metal media cabinet in a load-bearing wall in my basement, but unfortunately the cabinet is about 1/8" too wide to fit between the studs. Is it safe to shave off a ...
0
votes
2answers
1k views

Is it safe to remove 2 “extra” jack studs to make a 60" wide door opening wider?

We went to install our new main entrance 60" door (replacing double-door with single door and 2 sidelights). After we received the new door and shaved out more of the sheet rock, we saw that there ...
0
votes
1answer
3k views

Can the knock test tell you whether a stud is wood or metal?

I'm thinking about wall mounting a television, so I've used a stud finder to locate several studs in my wall. Out of curiosity, I knocked on the wall in several places to see if I could hear the ...
2
votes
3answers
13k views

How do I hang a pot rack in a plaster ceiling?

I am trying to hang a pot rack, and my house is all plaster walls. I have an electronic stud finder but the places it is telling me that studs exist don't seem to be correct - test nails have gone ...
0
votes
3answers
4k views

How should I mount a TV to a wall that slants inwards 8 degrees?

I am going to attach a piece of plywood across 3 studs and then attach the mount to the plywood, as described in the answer to Can I use 2x4s to extend studs so I can mount my TV?. However, my wall ...
5
votes
2answers
331 views

What features do I need in a stud finder for use on plaster walls?

I have an old house built in the early 1930s. The conventional stud finders are useless on plaster. The more sophisticated ones are more expensive in the $50 range. What features would a stud finder ...
1
vote
1answer
776 views

Hanging a new wall with Genie Clips and need to install a few studs. Will this affect the installation?

Here's what the bare frame looks like: If you don't already know how a wall is hung with Genie Clips, here's the video. Skip to 2:45 to see how they're spacing the clips. http://www.youtube.com/...
3
votes
1answer
2k views

Do I have studs on my plaster and lath wall around/above fireplace?

my home was built in 1892. The fireplace was a coal burner that has since been replaced by a propane fireplace insert. I want to mount a TV above the fireplace but am uncertain as to what is behind ...
1
vote
1answer
734 views

How can I hang a wall mount on misaligned studs?

So my wall mount teleco rack arrived. However my studs are 15" apart, not 16" so I can't put lag screws into more than one stud. I don't want to drill into the metal so close to the opening already....
2
votes
1answer
3k views

How can I secure a wall-mount server rack?

I would like to install a 2-Post 12U wall-mounted server rack in my utility closet. The rack will hold up to 200lbs. However, my equipment will be just under 180lbs. Most of the weight will be at the ...
2
votes
1answer
459 views

What can I do if I need another gang in a junction box but there isn't space in the wall?

I have a dual gang junction box installed in a space between 2 studs in the wall. I want to add swap the box for a 3-gang box to add another switch for a ceiling fan, however when I took the cover ...
3
votes
3answers
722 views

How can I build a table into an alcove?

I have this weird portion of a second bedroom where about 4 foot of it is 2 feet deeper than the rest of the wall. What I want to do is fix a butcher block in that space to use as a desk. What is the ...
1
vote
3answers
12k views

What do I do if drywall screws won't penetrate the studs?

We have begun a bathroom remodel project. All the studs were exposed by removing plaster, wood lath and old plastic tile. We began attempting to install the ceiling drywall first. We were able to ...
2
votes
1answer
1k views

How can I build a mantel around my fireplace?

I am new to posting on this site but have been reading it for a while! My wife asked me to redo our fireplace mantel. When I got the drywall off I noticed that the studs are not exactly uniform. I ...
3
votes
2answers
3k views

How can I mount heavy stuff on wooden studs?

I want to replace my kitchen cabinets (shoddy DIY stuff, very rough) with some nice floating shelves. I tried to find information on how to mount heavy stuff to wooden studs but all I found were ...
2
votes
2answers
1k views

Plumbing cuts through five studs. Is ok?

My kitchen remodel is in progress. After ripping out existing cabinets we found that the plumbing for the sink drain cuts through a total of 7 studs, more than 50% through each (see photos). ...
0
votes
1answer
64 views

Which stud should I mount to if they are different widths?

I'm trying to mount a pull up bar to the studs behind my drywall. The studs are 16" apart, but seem to be of different widths. Specifically, I see a 3.5" stud, 3.5", 2", 2", 3.5". Are these just 2x4s ...
0
votes
1answer
2k views

24" o,c, 2x4 for load bearing wall and rafters for workshed?

I'm making a small 12x16ft workshed. I want to go 24" o.c. on the walls and rafters (rafters may be 2x6, or 2x4 with supporting members), both for cost saving, and because it will create less thermal ...
1
vote
1answer
601 views

Possible to remove truss and add collar ties?

I am doing a pretty significant garage renovation and had a couple questions. I was originally going to just replace the loft (the original wasn't supported on top the stud wall on side which always ...
1
vote
1answer
50 views

What fastener to use to attach 4" circular pan to steel stud?

I need to attach a 4" circular pan circuit box to a steel stud in order to hang a bathroom vanity light fixture. The fixture weights less than 10 lbs, but assume some future homeowner will want to ...
2
votes
3answers
328 views

How do I know if I will drill into a hole in a wall that was already made?

I drilled 2 large holes for mounting a flat screen in the bedroom. One hole is in a wood stud and the other is a metal stud. I will be renting out our apartment and will be taking the TV down and ...
7
votes
1answer
13k views

What's the proper method for installing new studs in existing frame?

FYI - This is similar to a question I asked last week, but is about something more specific. Expect to see this image yet again in another question I will be asking later today :). Here's my wall: ...
0
votes
1answer
168 views

How to build a sauna? [closed]

I would build my own DIY sauna, but I can't seem to find extensive information about it. Nor I can find plans to build one. How can I build one? My father has a lot of home building knowledge, but we'...
2
votes
2answers
363 views

What's the point of a thin (1/4" width) piece of wood set diagonally between two studs?

What's the point of a thin (1/4" width, ~2-3" wide) piece of wood set diagonally between two studs? I just took out a piece of drywall for some other work I'm doing, and between two studs, there's ...
1
vote
2answers
7k views

Need to hang mirror, AC detected from stud finder

I'm a rookie with any sort of home renovation / improvement. My wife asked me to try and mount a mirror, its heavy, about 40 pounds. The mirror has two d-rings on the back and a big warning not to ...
2
votes
1answer
1k views

Can I attach a television mount using custom drilled holes?

I have a 94" wall with 14" studs. There is a stud right in the center at 47". I have been looking for a full motion mount wide enough, so that I can use the studs on both sides of the center. Meaning ...
2
votes
1answer
5k views

Can a condo interior room walls have steel studs that are paper thin?

I'm a bit puzzled about what's behind the drywall in my high rise condo built 3 years back. When drilling into an interior room wall supposedly where a stud should be(found by a stud detector and yes ...
1
vote
3answers
2k views

How to make paint stick to a stud screw?

Around my house, I have a places on my walls where the paint has fallen off of stud screws. They are not popped screws. Rather, they are still depressed into the wall, so I don't know how why this ...
1
vote
1answer
1k views

Notch rules or guidelines for steel studs (non-load bearing)

I'm trying to figure out what kind of notches (if any) are allowed in steel studs used for non-load bearing walls (for a finished room in a basement). IRC 2009 section 603 indicates that no notches ...
1
vote
2answers
767 views

Secure TV mount?

I'm not much of a DIYer, but I was thinking about mounting 2 or 3 TVs (not all mine, some my parents' etc), 32", 40" and 50". Obviously I'll be getting a stud finder and using that to find studs. ...
2
votes
1answer
2k views

Can I drill another set of holes in my studs to mount a TV?

I currently have a 47 inch TV which is mounted onto studs in my wall which is good. But now I plan to get 70 inch TV which means my existing wall mount frame must move a little upwards to fit above ...
5
votes
2answers
34k views

Why can't I find a stud in this wall?

I have problem locating my stud in my wall. I have tried many different ways to locate my stud but the results are weird. Using Stud Finder: The reading results are different everytime and weird. I ...
9
votes
1answer
2k views

What distance should I see between studs in a wood frame home built in 1943?

My house was built in 1943. It is a wood frame house and the interior walls are lath and plaster. My goal is to find the studs so I can mount a TV bracket for a flat screen TV. I have read that the ...
4
votes
1answer
13k views

What drill bit do I need to screw a hex cap screw into a wall stud? The magnetic DeWalt nut driver bits aren't an exact match

I am trying to hang a TV mount into the wall studs above a fireplace. The hex cap screws that came with the mount don't fit snugly into the 7/16" nut driver bit and are too big for the 3/8" bit. ...
3
votes
1answer
16k views

What are these horizontal & diagonal 'studs' in the wall called?

My single-story house was built in the 1940s in the San Francisco Bay Area (Earthquake-country). Here is a picture of the wall with the wallboard removed. This is from my neighbour’s house (Same ...
1
vote
2answers
2k views

Can I use metal studs for framing a shed?

We're building a shed on a pontoon so it will float. Therefore we need it to be light weight yet sturdy enough to hold up to snow in the winter. Will metal studs provide enough strength and support ...
0
votes
1answer
1k views

Small stud wall to sloping ceiling under stairs

We have an under-stairs toilet that we are replacing. The toilet was quite old, so the drain was 20cm from the wall. Apparently newer toilets require the drain to be pretty much flush with the wall, ...