Questions tagged [studs]

Vertical member in wall framing.

Filter by
Sorted by
Tagged with
37
votes
8answers
94k views

Should I use steel or wood studs for basement exterior walls?

Related: When should you use metal studs? I'm planning on finishing my basement. (assuming all water issues are resolved) I'll be putting up a water barrier (tar paper) on all exterior walls, ...
15
votes
4answers
95k views

If my wall has metal studs, is it better to anchor heavy objects through just drywall or also through the studs?

I live in an apartment that has that has metal studs. I'm considering hanging various things from the wall, including a coat rack that will span 5 or 6 studs. I've seen advice that says metal studs ...
5
votes
2answers
36k views

LCD TV mounting bracket does not “fit” the studs location in the drywall - how can I overcome that?

I would like to mount my 32" LCD TV to a wall using a swivelling bracket that I bought. The wall it needs to go to is plasterboard so I need to mount it on the studs. However, I've got a problem - the ...
4
votes
5answers
131k views

How can I mount a TV when I can't find studs inside my wall?

WARNING: I'm not the greatest handyman. I bought a TV mount the other day, expecting to hang my heavy 40" TV above the fireplace. However, the instructions specifically say to first screw the mount ...
8
votes
3answers
10k views

Can I wall-mount a TV when there is an air gap between the drywall and the wooden stud?

I'm mounting a 38lb TV (with a ~10lb mounting bracket). I located a stud, but the drywall floats an inch above it, plus the drywall itself is another 1/2 inch. So a couple 3-inch screws (and not a ...
10
votes
5answers
84k views

Can metal studs support a 64" plasma TV on a swiveling mount?

Alright, I need a sanity check here. I've been tasked with mounting a 64" plasma TV with an articulating mount onto a metal stud wall in the corporate boardroom. It's the quadruple-threat with no room ...
20
votes
5answers
33k views

How do I find studs when stud finders won't work?

I was trying to hang my TV at my new place, on an interior wall (between living room and a bathroom). Using the stud finder on other walls worked fine, but on this wall I got some very strange ...
12
votes
6answers
29k views

Am I having trouble finding studs because my walls are lath and plaster?

I picked a TV mount from Ikea. The TV itself is being mounted to some paneling which in turn is mounted to set of wooden draws. In addition, it gives you hardware to mount the panels to the walls. It'...
4
votes
3answers
2k views

Is it OK to install a TV mount when it can't be attached to a stud at all mount points?

I have a TV wall panel that can only reach two studs. I was wondering if it's fine to screw the left side and the center on studs, and have the right side anchored in the drywall. My TV is 30lbs with ...
15
votes
3answers
9k views

What should I look for when choosing a stud finder?

Stud finders are notoriously unreliable at finding studs; some will indicate a "rapidly shifting network of hundreds and hundreds of studs". Is there a way to determine before purchase that a ...
7
votes
7answers
387 views

Projects to Pursue while Studs are Bare?

I'm stripping my small 950 sq. ft. 1950's-era home to the studs -- walls and ceiling -- so that I can install a vapor barrier and insulation in the walls and ceiling. While I have the studs available (...
11
votes
2answers
9k views

When should you use metal studs?

When does it make sense to use metal framing for an interior wall? What are the advantages to traditional wood framing?
5
votes
2answers
34k views

Why can't I find a stud in this wall?

I have problem locating my stud in my wall. I have tried many different ways to locate my stud but the results are weird. Using Stud Finder: The reading results are different everytime and weird. I ...
5
votes
3answers
71k views

How can I pass cables vertically through walls that contain fire blocking?

How can one pass (speaker) cables through walls from the floor to the ceiling. I am assuming that drilling a small hole at the top, dropping the cable I want to pass through and catching it at the ...
3
votes
1answer
16k views

What are these horizontal & diagonal 'studs' in the wall called?

My single-story house was built in the 1940s in the San Francisco Bay Area (Earthquake-country). Here is a picture of the wall with the wallboard removed. This is from my neighbour’s house (Same ...
2
votes
0answers
4k views

Why can't I drill into studs more than 1 & 1/2 inches?

I am trying to mount a TV onto an "exterior" wall. I used the quotes because I guess technically it may not be exterior (I live in a townhouse with dividing walls between the houses). Anyway, I've ...
6
votes
2answers
31k views

How do you frame a wall more than 8-10 feet tall?

I am capable of framing a "simple" 8' wide 8' tall 4" thick wall out of 2x4 lumber, then attaching plywood or drywall or OSB or any other sheet material to the frame. Making the wall wider is a ...
5
votes
2answers
5k views

How do I locate studs in my wall?

First, I'm not the handiest of men, but can usually figure this sort of thing out. I just moved into an apartment in Manhattan and we're wanting to mount shelves, desks, and televisions to the wall to ...
4
votes
6answers
17k views

Can I use 2x4s to extend studs so I can mount my TV?

I need to mount my 55" TV to the left of the studs. Can I do this simply by running a couple 2x4s off the studs, and then connecting the mount to the 2x4s? While I imagine this can be done for lighter ...
3
votes
2answers
3k views

How can I mount heavy stuff on wooden studs?

I want to replace my kitchen cabinets (shoddy DIY stuff, very rough) with some nice floating shelves. I tried to find information on how to mount heavy stuff to wooden studs but all I found were ...
3
votes
4answers
9k views

How can I install an electrical panel when the stud cavity is too narrow?

I am installing a sub panel in my garage and ran into a problem. I have the usual 14" of space in the stud cavity but the problem is that the subpanel I bought is 14 1/4" wide. I'm wondering what ...
2
votes
1answer
3k views

what is the design load limit for a jack stud and header plate?

Assuming an over-strength column composed of one jack and two king studs - how much load can a single jack stud support - assuming #2 stud grade SPF for the header and jack. I've found a table that ...
2
votes
3answers
2k views

Attach partition wall to lath and plaster wall

I am looking to add a small closet (2×4 ft) in the corner of a room with lath and plaster walls. I would like to frame in two sides and attach it to the existing wall. Do I have to limit myself to the ...
1
vote
1answer
485 views

I need to know how to replace a water damaged wood rotten stud in a wall

I just bought a house built in 1930. The previous owners had a crack in the shower. I need to know how to replace the stud that holds up that wall as it is now rotten from water damage. The drywall is ...
1
vote
2answers
5k views

How can I straighten twisted studs?

I have a bunch of 2x4s that are twisted and warped. Is there a way to salvage them?
1
vote
2answers
5k views

Mounting TV on metal studs?

The wall contains metal studs 24 inch apart. On a previous TV, I installed an articulating TV mount (80lbs total with mount) on two metal studs with 4 snap toggles (that's 2 snap toggles per metal ...
0
votes
1answer
62 views

implications of small bottleneck in ductwork

I need to vent a sauna room (~200F) with an inlet duct that will open below the heater and an outlet that will open near the ceiling at the opposite side of the room. The ducts will be small (2"). ...
0
votes
3answers
4k views

How should I mount a TV to a wall that slants inwards 8 degrees?

I am going to attach a piece of plywood across 3 studs and then attach the mount to the plywood, as described in the answer to Can I use 2x4s to extend studs so I can mount my TV?. However, my wall ...