Questions tagged [smart-switch]

A smart switch includes electronic circuitry for remote control (beyond simple three-way switch wiring), smartphone or internet-based control, advanced timing capability or other features not found in traditional switches. Smart switches may require more (e.g., neutral) or fewer (e.g., signal 3-way with one wire instead of two) wires than traditional switches.

18 questions with no upvoted or accepted answers
Filter by
Sorted by
Tagged with
2
votes
1answer
66 views

Replacing 3-way Dimmer with Smart Dimmer

I'm trying to replace a 3-way dimmer set-up (currently a Lutron MACL-153M) with a smart dimmer. I have C by GE Smart Dimmers. After a lot of tinkering yesterday, I was unable to get it to work. I've ...
1
vote
0answers
22 views

Installing new Pir sensor switches

I want to install new motion switches to replace old light switches in basement, old switches only have 2 wires hot black, white neutral wire so I will need to run another wire for the load.is their ...
1
vote
0answers
39 views

Splicing or Extending 2.5mm2 Twin & Earth (UK)

I am trying to install a WiFi connected smart switch to control a ceiling light. The wall box is too shallow to accommodate this, so I need to install it inline. To do this, I need to move the circuit ...
1
vote
0answers
34 views

How do I wire three smart Wifi switches to toggle one another?

I have three Wifi switches that will be wired into the mains. Is it possible to have them act as a toggle for a set of lights? Ie, one switch turns on, they other two switches also turn on. Similarly, ...
1
vote
1answer
1k views

Wiring a GE smart switch in a box with 2 light switches sharing a neutral wire and switches sharing a hot wire on same circuit

Two switches in the box control 2 separate exterior light switches. I am attempting to replace one of the exterior light switches with a GE smart switch. I have three pairs of wires going to the two ...
0
votes
1answer
57 views

How do I replace this smart switch to this exisiting light switch

I have a deta grid single gang smart switch it has active neutral and a clear terminal. Before calling a sparky, I would like to understand what would be done. Is it a matter of connecting a wire ...
0
votes
0answers
36 views

Replacing a light switch with a smart switch

I'm trying to replace my existing light switch (in my new build home in the UK) with a Innens smart WiFi switch (https://www.amazon.co.uk/dp/B07RK5F8HC/ref=cm_sw_r_cp_apa_i_jNHbEbVEDEEF6 ). My ...
0
votes
0answers
51 views

Light switch replication

I appear to have a not so common request. I have two light switches which are located 1m (3ft) apart and control two ceiling lights located 2m (6ft) apart. There must have been some idea behind it, ...
0
votes
1answer
34 views

Dual light switch changing to dual smart switch

I currently have 2 switches. Each switch has a black wire and a white attached to it. I’m trying to install a dual smart switch, which requires 4 black wires and a neutral wire. Confused on how to ...
0
votes
1answer
42 views

GFI Leviton installation corrected

I corrected the Load and Line wires and now the green light is off but when i try to reset it just keeps popping out, i dont have anything plugged in for it to surge from, what do i do now?
0
votes
0answers
21 views

Wire ceiling fan switch with remote control to always on

How can I wire the switch of a remote controlled ceiling fan to always on so it can only be controlled with the remote. I basically want to have a smart RF controller (BOND) be able to control the ...
0
votes
0answers
19 views

Adding 'Smart' Capabilities to an outdoor Wisebox 4 Channel Receiver

I have a 4ch 10a Wisebox, which I use to control a bunch garden lights. The wisebox came with a wall switch and keyfob, which have a carrier frequency of 868.3 MHz. Now I'd love to be able to control ...
0
votes
1answer
110 views

Changing a 3 gang Australian light switch to a Smart switch

I am wanting to change the older style Australian 3 gang light switch with a new ‘Smart’ wifi 3 gang switch. I just need some help in getting the wiring in the right place. I have included pictures ...
0
votes
1answer
153 views

Uncapped wires in light switch box

I was trying to install a smart light switch, I don't have a neutral, so I can't do that. However, when I looked in the box, I noticed this other group of wires pushed to the back. They aren't capped ...
0
votes
0answers
23 views

Can a KNX smart house installation be reasonably maintained by an end user?

I am looking into transforming the light switches, curtains, and ACs in my house to a KNX based system. If I understand correctly, KNX is an open standard that allows anyone to configure their devices....
0
votes
1answer
159 views

Gosund smart switch

Gosund smart switch times out during connection process. Godsend app shows connection to be 100% complete but then shows failure/timed out.
0
votes
1answer
355 views

What did I do wrong with this Legrand RRW600U wiring?

I just moved into a new house, and I'm trying to wire up TWO Legrand RRW600U 3-way occupancy switches to a light in the basement. I want motion at the top or bottom of the stairs to turn on the light....
0
votes
0answers
96 views

How to automate a window to open & closed by remote commands

I'm a software developer. I would like to be able to open and close my window automatically when there is a noise outside. So first I need a Wifi Microphone, that will stream the audio to my PC. Then ...