Podcast #128: We chat with Kent C Dodds about why he loves React and discuss what life was like in the dark days before Git. Listen now.

Questions tagged [powertools]

The tag has no usage guidance.

Filter by
Sorted by
Tagged with
51
votes
8answers
165k views

When would one use an impact driver versus a regular drill?

Or vice-versa. As best as I can tell, the impact driver is very good for most any type of screw going through wood. When would you use a drill (with screw bit) instead?
12
votes
3answers
4k views

What type of cordless tool battery chemistry should I purchase?

I'm about to buy a cordless tool set in which the tools all operate off the same form-factor battery. The batteries come in several different chemistries and I'm wondering which type is better for ...
19
votes
4answers
18k views

Are there any cordless power tool systems that offer a corded option?

Are there any cordless powertool systems (e.g., drills, drivers) that have a corded battery option (i.e., an adapter that fits where the battery would normally go that can be plugged in)? I've used ...
12
votes
5answers
11k views

How can I protect my hands when using power tools?

When doing many DIY projects there's a strong need to protect hands against cutting by sharp part edges. Gloves seem a natural solution. However recently I was mounting a countertop and wearing ...
12
votes
3answers
6k views

Does a 2100W angle grinder need an earth pin?

I have recently purchased a Makita 2100W angle grinder. It has just the live (L) and neutral (N) connectors unlike the one I previously used, which had a third protected earth (PE) connection. Would ...
7
votes
3answers
14k views

What tools do I need to make a straight cut in laminated chipboard?

It's 38mm thick. Next week I will need to cut it along a straight line, and I would like the cut to be as straight and clean as possible. What tools do I need to do this ?
9
votes
2answers
18k views

Can I use an 8“ dado blade set in a 10” table saw?

I have a 10" table saw... this is probably a stupid question, but can I use an 8" dado blade set in this saw? Is one only supposed to use 10" blades in a 10-inch saw? I read on some contractor's ...
8
votes
9answers
262k views

How do I remove a drill bit that is stuck due to an overtightened chuck?

I recently bought a Bosch PSB 500 RE power drill and already I kinda screwed up the machine. The chuck is keyless, consisting of two parts which I'll refer to as the head and the base. You would ...
6
votes
7answers
39k views

What is a good way to cleanly cut through steel?

What tools can I use to get a clean cut through thin steel? Specifically, I have several mini beer kegs I need to cut the bottoms out of. I don't mind it taking a while, but my cuts are jagged (easy ...
4
votes
4answers
2k views

Solar power backup for router

I want to use solar panels to create a power backup for a router(9V, 1A). I'm aware I'll require solar panels and batteries but am not sure how to choose suitable ones. Please help suggest me on ...
3
votes
1answer
842 views

What router bearing can I use to reduce groove depth?

I order this 3/32 slotting bit from Amazon. Shank size 1/4, depth of cut up to 9/16. I only need 3/8 depth (slightly over is ok), but I could not find the right bearing. There are router bearing sets ...
2
votes
4answers
6k views

How to slightly enlarge a worktop hole for replacement kitchen sink

The task I am replacing my kitchen sink. The existing sink sits in a rectangular hole (with rounded corners) in the kitchen worktop. The worktop is about 1½" (40mm) thick and is made of some kind of ...
1
vote
2answers
3k views

Rotary hammers, how many joules to hammer through concrete slab?

I'm in need to buy a rotary hammer to make some holes in a slab about 12 cm thick of armed concrete. The holes will be between 5 and 10 cm in diameter, so I will have to hammer a round opening instead ...
0
votes
2answers
712 views

Can you get an “optionally cordless” or “hybrid” drill? [closed]

I'm looking to buy a new drill, but all of them seem to be corded or cordless. Are there drills that can either run cordless, or off the mains, depending on whether it's plugged in? It seems that ...