Questions tagged [plumbing-fixture]

The tag has no usage guidance.

67 questions with no upvoted or accepted answers
Filter by
Sorted by
Tagged with
0
votes
1answer
244 views

How do I remove the connected **plunger** of a bathtub linkage assembly that won't fit through the opening?

I have a trip lever mechanism on my old tub and want to replace it because the water stop lever is faulty and the tub drains and leaks slowly. I removed the cover plate from the overflow opening and ...
0
votes
0answers
358 views

removing handles from a moen 6010 bathroom faucet and install 1224 cartridge

I have a moen 6010 bathroom faucet assmbly. No screws visible to remove the cartridge. How do I get the handles off to gain access to the cartdridge?
0
votes
0answers
46 views

Tub Shoe tight to tub

I have an intermittently leaking tub drain, where it leaks to the ceiling below. Pulling the drain insert, and replacing the putty with fresh putty seems to help for a while. However, I was never ...
0
votes
1answer
88 views

Leak from valve on boiler - what should I do?

I have this valve which we use on the boiler to increase the pressure but it has just started leaking and is dripping through our ceiling. Can anyone suggest what I need to do to stop the leak?
0
votes
1answer
47 views

Recommend laundry tub automatic pump system

I've spend hours looking through various online catalogues and other sources for advice. What seems to be the most long-lasting and reliable design for systems that pump grey water from laundry tubs ...
0
votes
0answers
85 views

Can negative pressure in a PEX plumbing system cause or contribute to leaks?

Generally, when draining one's plumbing system all the faucets (or at least the ones at the ends of the manifolds or loop) should be opened so that all the water drains from the system and as the ...
0
votes
0answers
387 views

No hot water in kitchen but everywhere else is fine

Discovered issue today after being out of town for 2 days. When running water from a single handle sink - just cold water when turned to hot setting. Checked valves below sink. Cold valve turned ...
0
votes
0answers
791 views

Need to build a lip on half the front of the shower pan

I have a bit of a situation... I have a 3x5 Fiberglass reinforced acrylic construction designed for a 3 wall alcove. However, in my infinite wisdom, I overlooked this crucial detail and proceeded to ...
0
votes
0answers
45 views

What is this fitting in my 2" stack?

What is that wide-diameter fitting in my 2" PVC stack? It's in the way of the hardwood floor and the drywall. Can it be effectively removed?
0
votes
0answers
54 views

Hot water change to cold

I experienced a diverter problem. The diverter works fine when I the hot water flow out the tub spout, but switch it to the shower and hot water will become cold after couple minutes. I switch to the ...
0
votes
0answers
79 views

Help me open my thermostatic shower mixer to replace cartridge

So the thermostatic dial has ceased up and I want to open it to order and replace the cartridge. Trouble is I can't get it open! What I have done: Top handle Unscrewed the nipple with pliars and ...
0
votes
1answer
189 views

Stiff shower controls on recessed mixer

The temperate control is very stiff. How do I go about repairing this? Do I need to remove the whole unit? I can only find 1 Allen key hole where my finger is located. Thanks!
0
votes
0answers
167 views

Fix a faucet that has a groove

I don't know the exact term for the part I'm referring to so I'll describe it. The faucet's actual closing is done by something similar to this but without the slits for water. I assume that's called ...
0
votes
1answer
138 views

Should there be any moisture around a shower valve?

I just had a plumber install a new shower valve in a remodel and when I run my finger around the back of the ring on the front of the valve, I feel a little bit of moisture. It's a large walk in ...
0
votes
1answer
33 views

What is the name of this plumbing U wedge + connection

The two black pipes pictured below are connected, and a U-shaped wedge is placed between them, apparently to close the connection. What is the name of this connection or this wedge? I will ...
-1
votes
0answers
21 views

What are the insulation requirements for a wall-mounted faucet?

I've read that wall mounted (as opposed to counter-top mounted) faucets are fine so long as the wall is insulated, but could not find any information on the necessary R value of the insulation. This ...
-1
votes
1answer
432 views

Bath tub drain/stopper assembly cross has broken off and I can’t remove assembly

The cross section has broken off when I tried to remove assembly how do I get it off now?

1
2