Questions tagged [metal]

The tag has no usage guidance.

Filter by
Sorted by
Tagged with
1
vote
3answers
554 views

Can I shave the bottom of a metal casement window to get it to close fully?

I have a Casement Window installed that, as the new building has begun to settle, now has to be forced closed. It is on the verge of breaking the crank off now because it is so difficult. While wood ...
4
votes
2answers
877 views

How can I join vinyl decking to metal door frame?

Shoddy workmanship by a lousy contractor has left me with a vinyl deck that allows water to leak into the garage below. I identified the location of the leak - where the vinyl meets the metal frame ...
2
votes
5answers
1k views

How should I cut these speaker stands down to size?

Any recommends on what tool I should use and how I can go about not ruining the finish? Here's a close up of the top: And here's the finished product - thanks for all the help! I used a pipe cutter ...
7
votes
4answers
12k views

How can I fuse galvanized sheet metal together so that it is water tight?

Is it possible to fuse sheets of the galvanized sheet metal that they sell at the hardware store for roofing together so that it is water tight? I was thinking that this may be able to be ...
6
votes
16answers
57k views

What can I use as a thread “tightener” compound for a free-running bolt?

(I'm familiar with thread "locking" compounds, purple, blue, and red, but that's not what I'm looking for here. They lock once and then upon breaking the joint, do nothing further.) I'm looking for ...
2
votes
1answer
4k views

What is the best tool to grind down a smaller metal rod?

I am building this workbench and I have decided to recess the nut and washer inside the top of the bench, so that I won't cut/scape myself while I'm leaning up against it. Now my issue is that the ...
3
votes
1answer
961 views

How to remove paint and refinish metal fan housing front plate

I have an old exhaust fan from the 50s in my kitchen; the kind where you let a bead chain loose and it opens a hatch and the fan engages. Anyways, the fan has a metal faceplate, and a stainless steel ...
1
vote
2answers
227 views

Suggestions for dealing with the sharp corner of a storm drain

The (city-owned) storm drain outside my house has a corner that protrudes about half an inch from the line of the sidewalk. It's sharp enough to puncture a tire; I've lost a few to it over the years, ...
5
votes
1answer
2k views

Is there an issue using a stainless steel bolt with a hot-dip galvanized nut and washer?

Question says it all. Will there be a problem using a stainless steel bolt with a hot-dip galvanized nut and washer? This will not be a load-bearing application, will be exposed to outdoor conditions ...
0
votes
1answer
454 views

How do I increase the height of a sliding glass door lock?

I recently installed a dog door panel for my sliding patio glass door. The way the dog door was made I had to install it centered in the patio door channel vs flush with the sliding glass door. This ...
1
vote
2answers
641 views

How do I secure a steel rod inside a blind hole of a silumin part?

A part of my hacksaw responsible for keeping the blade tensioned broke apart. One of the parts is a piece of silumin which has a blind hole 4 millimeters in diameter and about 15 millimeters deep. A ...
2
votes
1answer
529 views

Why might a weld be weaker than a bolt? [closed]

I've heard that bolts should be used for connections that must be secure, rather than welds. To me this seems odd; I was under the impression that the whole idea of a weld was to make the two pieces ...
17
votes
5answers
13k views

How do I optimally cut a bolt to length?

Once in a while I need a bolt of exactly the right length and it is not one of the lengths available in stores. So I get a longer bolt and cut it to length. Here's the procedure I follow. I screw one ...
6
votes
2answers
18k views

Where can I purchase a block of aluminium? [closed]

I'm need a 5" x 5" x 1" block of aluminium. Is this something I can buy online and are there different types of aluminum to consider? Will I have to buy a bigger piece and cut the aluminum down to my ...
5
votes
1answer
609 views

How can I straighten a piece of wire?

I've once seen it on TV: in industrial wire production they use a set of castors that bends the wire back and forth, up and down – always a bit less, until its straight. Is there something similar for ...
5
votes
2answers
3k views

What is the best way to cut metal siding for soffit vents accurately?

I need to add a bunch of soffit vents to my eves, and I have (decorative?) metal siding such as in the picture. I need to do this quickly in the next few weeks before winter. What's the best way to ...
5
votes
2answers
4k views

What are the key differences between a step drill bit and a knockout punch?

Both a step drill bit and a knockout punch seem to be very similar, in that they both make holes in a metal box. The step drill seems to have an advantage, since it can make several size holes using ...
9
votes
2answers
32k views

How do I drill holes in Aluminum / Aluminium sheet?

I have some aluminum / aluminium strips that are about 3 mm thick and about 20 mm wide. I need to drill some holes in them. The holes will be 3.5 mm. What type of drill bit do I need? What speed ...
5
votes
1answer
446 views

Sourcing and installing a stainless steel backsplash

I recently replaced an over-the-range microwave with a hood. Since the hood is about half the height of the microwave, this left a ~15" gap between the preexisting tile backsplash and the start of ...
4
votes
1answer
4k views

methods of detecting a copper pipe in concrete floor

We believe that our copper water line is embedded in the concrete (and rebar) basement floor. We would like to excavate a hole to install a sump pump. We don't want to hit the copper line which we ...
7
votes
7answers
22k views

How to clean rust in hard to reach points on a tool?

I have a cheap tool with some rust on it. It's probably cheaper to buy a new one than to clean it. But I wonder if is there any solution where I can drop it and retrieve it clean. Is there anything ...
1
vote
1answer
205 views

Would this solution work with my dehumidifier?

I have a shed built with concrete blocks and a metal roof, terrible condensation in it and every time I go in, I see water on the walls and floor as well as drips on the metal roof. The shed is not ...
3
votes
2answers
13k views

How do I repair a garage door with a rusty bottom?

Was looking at my garage door as I pulled into home yesterday and noticed that the bottom panel is starting to rust slightly at the bottom. The rust looks like a small mountain range from one side to ...

1 2 3 4
5