Questions tagged [metal]

The tag has no usage guidance.

Filter by
Sorted by
Tagged with
0
votes
2answers
216 views

Mount LED Batten light to allow Rotational Direction change at various positions/ angles up & down using Hinge type mechanism?

I've got this LED batten light to replace old Tube lights. It's pretty light in weight and is full electrical fixture in itself, not needing electrical fixtures like before. It simply mounts on 2 ...
2
votes
1answer
41 views

What should the difference of inner to outer diameter of two pipes be to ensure one fits snugly within another? [closed]

One pipe is brass and the other is going to be made out of a hard plastic, probably acetal. I'm looking to be able to slide the acetal fitting over the the brass and have it snug enough so it doesn't ...
1
vote
2answers
47 views

How should I install metal corner trim on this slanted roof?

I've about got the metal on this tiny house and I'm having trouble figuring out how to install the corner trim at the top of the roof to make it look finished off. The roof is somewhere between a 3/12 ...
1
vote
3answers
37 views

Sealing metal siding against window j/c channel?

We're going to use metal siding on our house. We're using a corrugated profile. Where the siding meets walls/corners/windows, it will run into a strip of C-channel (or J-channel). Visually, that ...
2
votes
2answers
34 views

Screw sequence for Wood Subfloor to Metal Joists

I’m building a second floor in my metal barn. 12’x24’Space, joists are 2”x6” Metal 16” on center & the sub-floor is 3/4” ply TnG using 1&1/4” self-tapping screws. My questions: What is ...
1
vote
1answer
25 views

Looking for a large pull-down hinge mechanism [closed]

I have a large skylight, and currently have a shelf installed in it for indoor seed-starting. I would like to turn it into a pull-down shelf. I have found a clever design for hinges that might work, ...
0
votes
2answers
60 views

Chrome touch ups?

I have several chromed items where small amounts of the chrome has chipped off, leaving bare metal showing. None of it is in prominent areas, so I just want to touch them up. I havent had luck with ...
0
votes
2answers
124 views

push in / snap in panel spring clip edge fastener? help finding product or name

I've seen them many times before but can't seem to find the an image, name or product. You know the clip on your houses circuit breaker panel door that keeps the door closed. It's a little metal ...
1
vote
2answers
60 views

Can you screw roof metal directly to OSB between rafters?

I'm building a 14x16 tiny house and doing a metal roof. It's a slanted/skillion roof and the rafters are running down from the tall end to the lower end on 16" centers with no cross braces. I'm ...
2
votes
4answers
112 views

How can I grind a portion of the threads off a hex bolt?

I need to grind down the threads on a 4" hex head bolt while preserving 1 inch of threads closest to the head. I need to do 5 bolts this way. I'm thinking bolt in vise and then using a belt sander. ...
1
vote
1answer
85 views

Best way to paint Ikea metal brackets? [closed]

I'd like to paint in white my Ikea shelves's brackets (described thus: Aluminium, Nickel-plated, Clear acrylic lacquer). What would be the best (but hopefully cheap) route in terms of products I need ...
0
votes
1answer
52 views

What kind of screw should I use to affix plywood to a hollow metal door?

I need to affix a plywood frame (depth ~1.25 cm or so) to an office entrance door. The door is metallic, but not a solid metal block: it's hollow. The metal face of the door is about 2mm. This is the ...
0
votes
1answer
39 views

Best tool to cut 4mm thick straining wire

I need to cut several 1.5m hoops of 4mm thick galvanised steel wire. What's the best tool to do this at a decent pace?
2
votes
2answers
166 views

What's this metal thing in my wall where the studs should be, and how do I put a shelf on it?

I'm attempting to mount a shelving system (specifically, a Rubbermaid single-track adjustable shelf) to a wall and am running into something quite strange. Here's what I know: Studfinder appears to ...
2
votes
4answers
9k views

What kind of metal is safe for DIY BBQ repair?

The flame deflectors in the propane BBQ are rusted to bits. They sit an inch or two above the flames. For making new ones, I know to not use any galvanized or painted sheet metal. What kind of sheet ...
7
votes
7answers
22k views

How to clean rust in hard to reach points on a tool?

I have a cheap tool with some rust on it. It's probably cheaper to buy a new one than to clean it. But I wonder if is there any solution where I can drop it and retrieve it clean. Is there anything ...
3
votes
8answers
4k views

How to drill a 0.75" hole in metal

I'm trying to drill a 0.75" hole in a metal pole. I got a 0.75" drill bit from Home Depot (DEWALT 3/4 in. Black Oxide Reduced Shank Drill Bit) that I was told is appropriate for metal. I used a punch ...
1
vote
1answer
95 views

Grounding metal electrical boxes

I would like confirmation on the following: Is any metal box automatically grounded if it is supplied by an armored cable (without a ground wire) that is properly connected to the box and back to the ...
1
vote
2answers
445 views

hanging 140 lb on wall with metal studs

I am finishing my basement and have metal studs on the perimeter (just in case of any moisture penetration. Planning on hanging an 85", 140 lb flat panel on the wall. The drywall is not up yet, so ...
3
votes
3answers
2k views

How to repair large drywall section?

I had to remove a relatively large section of the drywall, approximately 24x24 inches. There are two metal studs at the sides. Should I try to cut out so both the existing and the new drywall will ...
0
votes
0answers
55 views

Can I leave one side of my metal frame dry half wall open for appliance ventilation?

I am installing an indoor metal frame half wall that will hold a countertop in a bar. The The wall is L shaped and anchored on concrete and against a wall at the top of the 'L'. The long part of the '...
1
vote
1answer
73 views

How to install door security guard on metal door jamb?

I bought a door security guard that looks like this The instruction coming with it says I need to drill a 1/8‘’hole first on the door jamb and put the screws in it, but I am not sure it would work ...
1
vote
1answer
41 views

Are watchmaker or mini lathes useful to make adapters and threaded rings for photography and optics tinkering?

Old watchmaker lathes, or very small lathes like the Proxxon FD150/e look affordable used, and not very space consuming either. Can these be used, by a non expert, to build aluminium parts like ...
1
vote
1answer
110 views

How can I install a TV mount to metal studs?

I'm trying to mount a tv in the new apartment. I thought I found and marked the studs and drill holes, but when trying to drill though met resistance. I'm able to look into the wall a little because ...
2
votes
2answers
64 views

Round or half-round files sold by radius?

I'm trying to find a half or full-round file of a particular diameter, but it seems to be rarely mentioned (and when it has been, they've been much smaller than I'm looking for). Are they just not ...
0
votes
2answers
102 views

Stripped hole in furnace fan housing assembly

In the furnace blower housing, where the blower motor sits, the holes have gotten may be a little bigger. This is a thin piece of metal where the screw sits. But now my screw keeps rotating. On two ...
1
vote
1answer
52 views

Mounting articulating Arm for TV (43”) to wall with metal studs

I’d like to mount an articulating arm for my 43” TV in my basement, however have metal studs unfortunately. The mount is made for a single stud install. Luckily I have access to the back side of the ...
0
votes
1answer
57 views

How to remove broken hinge which is stuck inside

There is a broken hinge which is stuck: To compare, a good hinge is removed easily like this: I tried to remove broken hinge with a hammer, however it is stuck very firmly. Is there any method to ...
4
votes
5answers
57k views

What is the metal I have in my wall?

I've been trying to mount a TV on my wall, and have encoutnered a problem locating and drilling into studs. I used a stud detector to look for studs in my wall, and proceeded to drill. Instead, I ...
0
votes
1answer
121 views

Metal Studs - How they should be installed?

What is the way metal stud should be installed? Is there a reason they should be, a same way, as in upside down? And precut - holes line up.
0
votes
2answers
197 views

Attaching a wheel to a metal rod (axle)?

I have a wheel (1/2 inch diameter) and a metal rod (1/2 inch diameter) [axle]. Currently, the wheel on the axle results in the wheel free-spinning. How could I attach the wheel to the axle? (The ...
1
vote
1answer
41 views

Crimping a plate border with metal

For a DIY development I need to crimp a metal border (anykind, the important is that it's conductive) to a plastic plate of ~1 mm wide and few cm length as shown in the picture. I guess it exists for ...
0
votes
0answers
57 views

How to properly drill new holes in metal door for installing new door hinges?

I need to replace some old door hinges and the current hinges only have 2 of the 4 holes drilled. I am installing 4x4 self closing hinges and want to have all the screws installed. Problem is I did a ...
1
vote
1answer
27 views

Ms Rack for batteries

I want to use 4 rectangular hollow ms pipes 40*25*2 mm. 25 mm vertical use. All 4 pipes will be equally spaced between a width of 490 mm. The length of pipes is 1390 mm, with these 4 pipes resting on ...
1
vote
5answers
170 views

Hanging things on metal studs

My house has metal studs (South Florida) and I cannot figure out how to easily get screws into the studs for hanging things such as curtains. I have tried the pilot hole approach with a titanium drill ...
9
votes
13answers
53k views

What can I use as a bowl for a DIY fire bowl/pit?

I'm looking at creating my own fire bowl, as I would find it more fun and satisfying instead of just buying one and plonking it down. I haven't decided if I want it standing or sunk, but that doesn't ...
0
votes
1answer
79 views

Are these corner brackets that hard-to-find? [closed]

I was searching for this a particular corner brace/bracket, but it seems that they are impossible to find. I couldn't them at home depot or at amazon. I'm not sure if they just don't exist or if I'm ...
0
votes
1answer
58 views

Does this bracket exist to hold two tiles together?

I don't think it's the best title, but I don't know what else to use. I have several of these large tiles, and I want to make a planter out of them. Is there a bracket (like the image below) that I ...
4
votes
8answers
7k views

How can I drill a big diesel tank without emptying it first?

Need to make a hole in a big steel diesel tank. I would say it has 5000 liters capacity, and it should have at least 2/3 filled or more. Metal Sheet: At least 3 mm thick. Drill hole is 1" or 2", not ...
1
vote
3answers
2k views

How to cut stainless steel sheet without burning it?

I need to cut out a small section of 1.5mm Stainless steel. Before, when I've made cuts I have used an angle grinder and its resulted in thr stainless becoming scorched/burnt and I can't remove it. ...
-1
votes
1answer
51 views

Best way to make sturdy Fence post for aluminum sign?

I'm looking at putting some posts up for No-Smoking signs at a local club frequented by a couple hundred kids a weekend + their families. One guy recommended Treated lumber, but I heard it'll eat ...
1
vote
1answer
192 views

How can I attach a kick down door stop to a hollow metal door?

I have a hollow-core metal door out to my car port, and it gets a lot of traffic. I'd like to add a kick-down door stop to the door. I think one option is to drill pilot holes and use self-tapping ...
2
votes
4answers
1k views

Tool for straightening a bent metal bar of the gate?

Someone's car hit our metal bar gate, so one of the rods is bent as shown in the photo. What kind of a tool can I use to bend this back, so it's straight? Thank you!
2
votes
5answers
8k views

Will galvanized metal conduit balusters resist rust?

I'd like to use galvanized metal conduit as deck balusters with pressure-treated lumber. Will the bare metal resist rust? If not, is there an inexpensive way to improve its rust resistance?
0
votes
2answers
29 views

Sink top: spray gun lacquer or metal enamel?

I am thinking in mounting a washbasin into a 3mm steel plate. The plate will be painted in a Klein Blue. Considering that it will get wet and that there won't be too much ventilation in the room... ...
1
vote
3answers
309 views

Found metal while drilling into a stud

I hired someone from Amazon Home Services to install a TV wall mount. As the person was drilling holes into studs, he found metal when drilling one of the holes. He wasn't really sure what he was ...
1
vote
3answers
17k views

How can I update this very stubborn antique bed frame so the mattress fits properly?

How stubborn you ask? Well the bed frame has three issues, but really only one and the other two are only a result of the first: The rails are too short. Not by much, maybe an inch. Maybe even less....
13
votes
2answers
4k views

What metal is most suitable for a ladder submerged in an underground water tank?

I need a ladder in my underground water tank at home, to enable easy access for cleaning and maintenance operations. The water from the underground tank is used for drinking, apart from other ...
1
vote
0answers
42 views

Am I hitting metal studs?

Novice here. I'm trying to install a swing arm lamp in the corner of two walls, one of which is an exterior wall. The magnetic stud finder I have indicated that there's a stud on the interior side of ...
1
vote
0answers
235 views

Options for sealing hot rolled (mild) steel with a matte finish?

I'm building a book shelf using 1.5" angle iron made from hot rolled steel as the frame. It's my understanding that this steel will rust even if left indoors. While I like the raw, industrial look of ...

1
2 3 4 5