Questions tagged [load-bearing]

A load bearing wall supports the structure above it, and thus cannot be removed without replacing that support. Use with the [walls] tag

Filter by
Sorted by
Tagged with
0
votes
4answers
3k views

Is this wall load bearing?

I want to remove these three small pieces of wall (Marked in yellow arrow) to combine dining and living room? Since the house has a basement. I also attached the basement pic to show the structure ...
4
votes
1answer
2k views

Does a long deck beam need a post at staggered joints?

I am designing a deck that requires 40' beams. In that design I plan to fabricate the beams with 2-2x12 pressure treated lumber. I have tentatively planned to arrange the plies in this fashion: 1st ...
3
votes
1answer
2k views

How safe is my patio and how much weight could it support?

I live in a three story apartment. I have a patio which also has a storage off of it. The actual patio is 8 X 10 and made from decking boards. However the exterior corner is supported by a 4 X 4 for ...
5
votes
3answers
17k views

Is this wall load bearing based on the attached blueprints?

I would like to remove a wall in my walk-out basement but I don't know how to interpret this architectural blueprint. Based on this blueprint, is the wall bearing load or not? I have highlighted the ...
0
votes
1answer
591 views

Open up a loadbearing wall

I need some help on sizing a header. My house is 19ft wide about 24ft long 2story with a small loft attic. House was build in 1915 so its balloon framing. The wall I want to open up is 12ft long on ...
3
votes
3answers
220 views

Can I remove the framed wall on the outside of my basement?

I have a 20 year old house (which is a basic colonial box). The basement has a standard poured concrete exterior wall. Against the concrete exterior wall, they framed a standard wood 2 x 4 wall, ...
2
votes
3answers
2k views

Is it safe to shave off 1/8" from a load-bearing stud?

I am trying to install a small metal media cabinet in a load-bearing wall in my basement, but unfortunately the cabinet is about 1/8" too wide to fit between the studs. Is it safe to shave off a ...
1
vote
0answers
6k views

Load bearing capacity of 2x6's for diy lifting cage

I want to build a custom power rack to safely perform heavy barbell exercises in my home. Commercial racks are too tall for my basement. Others have done this before: http://www.home-gym-bodybuilding....
1
vote
2answers
125 views

Will the highlighted legs bow?

I don't really know much about building anything so I was trying to keep this as simple as possible (2x4s and OSB, wood glue and screws). I'm worried about the highlighted legs bowing. This is for a ...
0
votes
1answer
2k views

24" o,c, 2x4 for load bearing wall and rafters for workshed?

I'm making a small 12x16ft workshed. I want to go 24" o.c. on the walls and rafters (rafters may be 2x6, or 2x4 with supporting members), both for cost saving, and because it will create less thermal ...
2
votes
1answer
606 views

What would a calculation be for the weight bearing capacity of 6 x 2 studwork?

I'm building a campus board (a training aid for rock climbing) and my landlord wants to know how someone can be sure a person's body weight can be supported from it. I'm at a loss on how to give him ...
0
votes
2answers
24k views

How much of this load bearing wall can I remove?

How far can I spawn a gap between posts on a load bearing wall? I have an entry way from the living room to the dining room / kitchen area that I would like to expand. How far can I span across and ...
2
votes
1answer
2k views

Is this a load-bearing wall between my house's entrance and dining room?

I have recently bought a home in which there is a wall at right at the entrance of the foyer. Is there any way to tell if it is a load-bearing wall? I just want to get rid of it.
5
votes
1answer
2k views

Hangman's Noose vs Uni Knot

Is there any practical difference between the Hangman's Noose and the Uni Knot (a.k.a. Duncan loop)? The difference I see between the two is that the coils are wound inside the loop in the uni knot ...
4
votes
1answer
3k views

Is this a load bearing wall?

The first floor of my home has a small bathroom attached to the kitchen. Bathroom has(had) a pretty standard 2 door closet. I say standard because it's the cheap kind you buy at Home Depot that's ...
8
votes
1answer
21k views

Can I safely make a door frame taller?

UPDATE: April 22 What I ended up doing was removing the trim non-destructively. Above the door frame, it was clearly not load bearing, so I continued and was not so non-destructive. The end-result ...
4
votes
1answer
2k views

Can you tell from this frame if it is a nonbearing wall?

Just removed the drywall and need help to confirm if it's a non-bearing wall. It's a 1900 duplex house and there is a similar wall on the first floor but it is not aligned, about 10" distance. ...
4
votes
1answer
3k views

How many jack poles should I use when opening a doorway through a load bearing wall?

I'm opening a 6-foot wide opening in a 19-foot section of load bearing wall between two rooms on the main level of two-level-with-basement home. I'll be installing a built-up 4x10 header (using (2) ...
14
votes
2answers
19k views

Can I remove a wall stud to install a pet door?

We only have one option for a wall that the pet door would go in. After measuring we found that the door would have to go right in the middle of a stud. Is it safe to cut through the stud?
0
votes
1answer
239 views

How much does weight affect a house?

I just demo'ed a bathroom. At 50 trashbags at 50 pounds a piece I am guesstimating that I took out 2500 pounds. The materials I am using to replace everything in the bathroom are about 800 pounds ...
6
votes
1answer
3k views

What should I do to level an uneven floor with a potential load bearing wall above?

I'm trying to level the first floor in my 90 year old house. The floor joists are held up by a wooden beam composed of 5 2x8s, which is held up by two steel columns. In the middle of the wooden beam ...
0
votes
2answers
2k views

What size lumber do I need for a mezzanine floor to support a 20,000 lbs load?

I am thinking of putting a mezzanine in my garage to support 20,000 lbs of load, not including the weight of the floor. On the floor the area is 20' deep X 32' wide; I was looking at 4" X 12" ...
6
votes
2answers
6k views

How much temporary bracing do you need when cutting a new exterior door opening in an existing house?

I'd like to add a door to the back side of my garage, but since this is a load bearing wall I'll have to brace it temporarily while I frame the opening. The garage has one room above it, which spans ...
2
votes
1answer
994 views

Installing a swing set between two brick walls?

My neighbors and I are considering putting up a swing set in the alleyway between our houses. The space is about 10' wide, and the house walls on both sides are brick (about 4" thick). Which of the ...
5
votes
2answers
3k views

I removed this non-load bearing wall in the corner of my basement, now 2 doors upstairs rub on their frames. Why is this?

In the image below, notice where the small 1x1 bits are, running perpendicular to the ceiling joists. These was used by the previous homeowner to lower the ceiling in one room, so if you can imagine, ...
9
votes
1answer
872 views

Can I modify a load bearing triple stud?

I am installing a small safe in a wall and when I cut the opening in the drywall I noticed that the studs were in an unusual distribution. The stud on the right was normal but then there were multiple ...
4
votes
2answers
2k views

How should I install a hoist given that the walls and ceiling are made of concrete?

I have this hoist, of the engine-lifting variety, which is designed to be installed below a pipe or beam. I do not have any load bearing pipes or beams. What I have are a poured concrete ceiling (9" ...

1 2 3 4
5