Questions tagged [joists]

Horizontal support structures beneath the floor running between load bearing walls.

33
votes
1answer
146k views

What are the guidelines for holes in joists?

I've been unable to find a good reference for the size/amount/location of holes I can drill through joists. This is mostly in order to pass cabling or pipes through the joist crosswise. Also, what ...
8
votes
4answers
4k views

Floor joists connection to eaves

Apologies if this is a duplicate. I'm attempting to floor my loft space. It currently has 47mm x 75mm ceiling joists, not enough for a floor. I am going to add something like 47mm x 200mm along ...
6
votes
3answers
6k views

Is it OK to drill vertically through a joist?

I just bought a new house and I'm looking to run some cables. One of the areas I would like to run it to would require drilling through a 2x10 sistered joist. Realizing that going through the joist ...
5
votes
2answers
3k views

Is there a limit to the number of holes bored in a joist?

I already know that a hole bored in a sawn lumber joist cannot be within 2" of any edge or any other notch or hole. And that the hole can only be a maximum of 1/3 the depth of the member (...
3
votes
1answer
3k views

Where in the span of a floor joist can I drill holes to run wiring?

How far from the end of a 2x12 or 2x10 floor joist can I drill a hole? NEC 502.8 does not give this answer, only that you have to be 2" above or below the edges, not in what part of the span it has ...
0
votes
3answers
6k views

Knee Brace support Hanger for Treehouse

I am going to be building a Treehouse soon, and am researching the best and most cost effective means to do so. I am good on the platform and beams (using Treehouse Attachment Bolts), and am going to ...
6
votes
1answer
28k views

How can I attach a ledger board to my house?

Spring is here so I finally started to take measurements for materials I will need to build a new deck on my recently constructed home. I just realized that this isn't going to be quite so simple as I ...
7
votes
1answer
5k views

How should I attach a chin-up bar to floor joists?

I want to mount a chin up bar to engineered I-beam floor joists. Am I safe to mount it directly up into it with lag bolts? If the spacing isn't correct and I span some joists with 2x4s, should I run ...
5
votes
1answer
5k views

Do the guidelines for holes in joists apply to band joists?

This question have a great answer with all the guidelines for drilling holes in joists. The question: Are the guidelines the same for band joists? A bit of context: I'd like to add an exterior ...
1
vote
3answers
5k views

How can I repair the end of joists sitting in brick pockets?

I have 2x8 joists over an 8 foot span that were eaten by termites on one end. I need to repair all of the joists in a small room. The building is double wythe structural brick that is approximately ...
9
votes
1answer
2k views

How do I get to the wall cavity above a double floor joist from below?

I am running some new romex for a couple of electrical outlets. One of the outlets is on one side of a wall in one bedroom and the other outlet is on the other side of the wall in another bedroom. ...
6
votes
1answer
1k views

How do I fit a joist in this small space?

This is a follow on question from here: Floor joists connection to eaves Since this question, I have been told I need 8" joists for my span and I have exposed my eaves area to see what space I've ...
6
votes
1answer
2k views

Should I worry about sagging joists?

I have a two story house and some of the joists between the floors are sagging about an inch or two. When I walk around upstairs I can feel the level difference and downstairs you can slightly see the ...
3
votes
3answers
687 views

Would drilling a small hole through joist / sole plate cause structural problems?

New home owner. I need to wire some ethernet and coax across the basement up into to the first floor wall. The perimeter wall is cinderblock, it is a twin and this is the shared wall. It looks framed. ...
3
votes
3answers
6k views

How to hang a chair from the ceiling joists (with attic access)

I'm planning on hanging a chair from the ceiling. From what I can tell the best method is to add a crosspiece above multiple joists, and mount the chair to that using an eye bolt. The problem with ...
2
votes
2answers
3k views

Do I need to brace joists after removing basement ceiling?

I'm about to take out the lath & plaster ceiling in the basement of my 1908 house (I'm hiring it out; I know how bad the mess is). Main reasons for doing this are to get access to wiring and allow ...
2
votes
2answers
7k views

Is deck joist sistering a sloppy repair?

I have a few bad deck joists that I replaced with new PT joists. These repairs are great. Now I have a few more not too bad joists that will be rotted in a few years. I am thinking to add new PT ...
1
vote
2answers
20k views

What is the best way to hang a heavy dynamic weight from a flat ceiling with joists?

I want to hang something like http://www.skychairs.com/ or similar in my living room. If the joists were exposed I would mount a beam between two of them and hang over or through that. However, when ...
1
vote
2answers
594 views

Why are my joists smaller than standard size?

I was preparing to replace a cantilevered rim joist on my house today. I bought a 2x10 treated board to replace it. I cut a piece to use as blocking and found that the board was much wider than the ...
0
votes
0answers
664 views

Can turnbuckles hold a frame in tension?

I'm building a king-sized bunk bed using a loft/joist design. Basically, I've got (see below): slats nailed into joists joists joined to headers with blind tenons headers joined to posts with blind ...
0
votes
2answers
156 views

Drywall installation when ceiling joists lower at the edge

I am trying to install ceiling drywall and everything is fine until I reach the edge. You can see there are 3 2x8 joists at the edge and it's somehow positioned 1/2" to 1" lower than the rest. So my ...