Questions tagged [hood]

Questions related to over-the-range hoods. For range hoods which have a microwave built in, use microhood.

14 questions with no upvoted or accepted answers
Filter by
Sorted by
Tagged with
2
votes
0answers
48 views

Best tool to cut existing tile sidesplash to fit new range hood

Our new range hood doesn't sit square or flush with the wall because the new hood sits over some of the original tile (outlined in red). I plan to trace around the hood and remove a 5-inch wide by 1....
1
vote
1answer
35 views

Kitchen extractor duct sizing and fitting

I've just had our kitchen re-done. We've got a new kitchen extractor hood (Zanussi zfv919y), which has a 150mm duct outlet, with a set of flaps (anti-backdraft?) where it exits the hood. The old ...
1
vote
0answers
199 views

Stove Vent Hood Not Pulling Air

My stove vent is not pulling enough air but the exhaust on the outside of my house is flowing really good. The metal grease filters have been replaced (in fact with the grease filters removed it still ...
1
vote
0answers
39 views

What are Range hood exhaust exterior wall location requirements?

What are the requirements for a residential range hood exhaust location on the exterior wall?
1
vote
0answers
152 views

Cooker hood venting close to eaves

I have had a new single story extension built to first fixtures; this includes a new kitchen area. Building Control (UK), will not sign off the extension until an extractor hood is fitted with ...
1
vote
0answers
172 views

Can inline range hood exhaust fan damper be safely/legally installed,1st floor of 2 story apt

I live in a 2 story apartment. Whenever the tenants directly upstairs turn on their range hood exhaust fan, I get whatever they are cooking/burning in my apartment. I have pulled down the range hood ...
1
vote
1answer
500 views

Do I have to provide better support when hanging a range hood from soffit framing?

I recently purchased a house and am currently renovating my kitchen. I have gutted the kitchen and changed the wall between the kitchen and living room to a half wall. The design I have now is setup ...
0
votes
0answers
30 views

Is 4in pipe OK for range hood with 7in vent?

We bought a 350 CFM range hood with a 7in vent. Our installer ran a 4in diameter flexible aluminum foil air duct horizontally through the floor joists to outside. We are now told the 4in pipe is too ...
0
votes
0answers
48 views

Sharing kitchen hood and kitchen ventilation through one duct

My kitchen currently does not have a kitchen hood, so I'm planning to install it. At the moment there is a ventilation duct, my idea is to connect the hood pipe to the ventilation pipe in the drop ...
0
votes
0answers
29 views

The proper kitchen hood

I have the following kitchen setup. The red line is the duct of width of cca 6 inches (15 cm). The kitchen is part of a living room which has volume of 90 m3 but is also connected to a hall of cca 26 ...
0
votes
0answers
27 views

What is a compliant box for a range hood in terms of a correction request by an inspector?

I’m remodeling a kitchen and the electrician wants to charge extra to fix wiring issues with the range hood and junction box. However, the inspector told me that one of the corrections the electrician ...
0
votes
0answers
471 views

Island Range Hood Not Centered above the Stovetop

He, I'm in the process of doing a small remodel to my kitchen. We took out a half wall that the stovetop is positioned in front of and are converting the wall mount hood to an island. My issue is that ...
-1
votes
2answers
3k views

Cutting stainless steel vent chimney to fit sloped ceiling

Looking for thoughts on how to cut a stainless steel hood vent chimney to match the profile of a angled/sloped ceiling. BEHIND the drywall is 1” of insulation and then the roof. Should this be done ...
-2
votes
1answer
528 views

Where can I purchase exhaust blowers for custom island range hood and how do I install it?

I want to purchase a custom copper island range hood that I believe doesn't come with the fan itself. Where can I purchase the parts for the fan and light system and how do I install something like ...