Questions tagged [hanger]
The hanger tag has no usage guidance.
12
questions
0
votes
1
answer
79
views
Can mild steel square tubing 33x33mm Square with 2mm walls support a desk-top?
Here is the basic idea: An L-shaped computer desk mounted to the wall with no legs. (Screens will be mounted on the wall.)
This is the Mounting Bracket:
The length of the tube will be 22", ...
- 104
0
votes
1
answer
209
views
How many nails can be in a floor joist before it's a problem?
This sounds like a weird question but I can't find an answer online to it. We have a non-loadbearing partition wall that is sitting parallel to but between two joists. In between the joists, there is ...
- 103
0
votes
2
answers
110
views
Is it possible to repair this hanging mechanism
We bought some used furniture to put up on the wall. Yesterday we tried to put it up but it became apparent that we couldn’t tighten the screw on one of the hangers to bring the cupboard close to the ...
- 103
1
vote
3
answers
591
views
How to replace deck joist hanger in place?
I have a deck joist hanger or two that I was considering replacing in-place if possible. The issue is this deck is 20+' in the air on uneven ground so supporting the joist from underneath before ...
- 387
0
votes
2
answers
137
views
Strengthen ceiling joist with external bridge?
I have 2x6 ceiling joists in my finished garage and have attached a ring hanger on a single joist. When I hang my entire body weight there is an almost imperceptible amount of sag on the joist. ...
- 1
2
votes
1
answer
280
views
Install hose hanger with Regular drill and bits
Disclaimer: I am very newbie when it comes to DIY stuff, so be patient :)
So I have installed this hose hanger into my exterior brick wall using 12V cordless drill. Looks sturdy, but I do have some ...
- 209
0
votes
1
answer
218
views
At what height should I install my (coat) rack? [closed]
I'm planning to install a coat rack on the right side of my bedroom closet, at the place marked with *:
+----------------+
| |
| |
| |
| |
| ...
- 2,597
2
votes
1
answer
223
views
Supporting this old 2x4 hip roof rafter to the beam
I'm renovating an old house which had a hip roof. One of the roof rafters (2x4) comes down on an angle and isn't supported on the beam. I thought a strong tie lssj would work but the rafter is a bit ...
- 121
-1
votes
1
answer
45
views
What do you call a door-attached bar for hanging belts?
Closet doors, particularly those for the closet section which houses a rail with hangers, often have a sort of a cylindrical bar attached to the inside of the door. A thin bar at a short distance from ...
- 2,597
0
votes
1
answer
5k
views
How to hang a frame with a sawtooth hanger from a wall?
This might be a 2 part question so I can break it out into two parts if needed.
How do I hang a frame with a sawtooth hanger onto a wall with a nail?
Can I use a screw and anchor on the wall to hang ...
- 614
1
vote
1
answer
348
views
Is using a single hanger plus a framing angle on a double member sufficient
I recently had a deck built. The deck has a few places where double joists are used between beams to allow cutouts for trees. The framers used single joist hangers for the 2x6 16" oc joists.
On ...
- 12.8k
0
votes
0
answers
40
views
Hanger or recommendations for steel hanger for deck beam
I am building a deck. One of the beams (beam 1 in sketch) is a 20' x 5-1/4" PSL beam. The beam is sitting on a 6x6 concrete post with a carport post saddle on one side. My plan is then to ...
- 12.8k