Questions tagged [finishing]

The tag has no usage guidance.

Filter by
Sorted by
Tagged with
0
votes
1answer
42 views

Laminate Stair Nose Installation

Below are all the pictures that correspond to my question. Last night I installed some stair nose molding and tried to follow the instructions the best I could (the part of the instructions in ...
0
votes
2answers
606 views

How to Fill Gaps Between Hardibacker and Drywall?

Trying to figure this out. I am going to be using Hardibacker for wet areas around the tub-shower above the acrylic tub/shower surround, and drywall for the rest of the room. There will be no tile. ...
0
votes
1answer
338 views

Can I put insulation under roof between joists

I bought an old home. There is new blown in insulation on the floor of the attic. The attic will not be a bedroom BUT will eventually be a kid's playroom. My plan is this: Build a subfloor over ...
0
votes
3answers
2k views

How should I refinish vintage wooden closet doors?

I have old closet doors that look like this: The lacquer is worn out and aged and they look really bad but there are no visible scratches or dents. I am thinking of replacing the aged hardware ...
0
votes
1answer
150 views

When does sanding(smoothing out wood surface) sensibly apply

I know I can smooth surface right after stripping is done. And I read somewhere that I can choose to perform smoothing step after pre-conditioning step instead. What I would like to know is if I can ...
0
votes
1answer
271 views

How should I finish the area around the gas line for my range?

We are remodeling our kitchen and had a new gas line run for our range. What's the best way to finish the area around the valve? We'll obviously will need to access the valve and run flex pipe from ...
0
votes
1answer
25 views

Waxing Spar Urethane finished product

Is it practical to wax an article that has been finished with spar urethane? This item will be exposed to the weather for 4 - 6 hours on occasion. If waxing is practical, how long should the urethane ...
0
votes
1answer
67 views

Should I sand between coats of polyurethane when finishing a table?

I am finishing an oak table. I lightly sanded the polyurethane after the first coat, as per the instructions. After the second coat of polyurethane dried, I see sanding/brush marks. If I don't sand ...
0
votes
1answer
46 views

Wood finish to handle high temperatures (not turn cloudy)

I'm building a mobile bench top for my home brewing system. The system will be all electric powered by heating elements actually in the kettles (think hot water heating elements). When this type of ...
0
votes
1answer
27 views

Changing gloss marble finish to honed finish

How can I tone down the gloss of a small marble countertop. It is currently high gloss, and I would like to reduce it to what is usually called a honed finish. My inclination is to use wet emery ...
0
votes
1answer
781 views

How / Should I insulate my Basement Walls

I’m finishing my basement and thought about insulating the walls. Picture of my basement attached. The house is about 22 years old. Poured in place concrete walls, no history of water. I started ...
0
votes
1answer
427 views

Raising interior prehung door before installation?

I am getting ready to install standard height interior prehung doors. I will have carpet installed afterwards and would like to set the doors at a good "standard" height to prevent having 1.) a big ...
0
votes
1answer
42 views

How to I apply a 'standard clearcoat 30 sheen' to some unfinished hard maple

I have some hard maple stair tread which according to the manufacturer has a 'standard clearcoat 30 sheen'. I also have the stair risers, also hard maple, but that are unfinished. I wish to apply an ...
0
votes
2answers
2k views

Should I use a stripper or sander to remove paint on my deck?

I have a deck that's maybe 10 years old and the previous owners used paint instead of stain. I want to remove the paint and I already started with the Behr Premium Stain and Finish Remover, but it's ...
0
votes
1answer
368 views

Staining Plywood

I bought some plywood from Michael's (1/4" x 12" x 24") that I am going to woodburn some designs on to. However, I'd like to put some sort of finish on the plywood so it looks more refined/elegant and ...
0
votes
2answers
4k views

How to finish bathroom vanity junction with the floor?

Hello Internet DIYers! I'm in the process of remodelling our bathroom. The floor is done and I have installed the vanity (I screwed it to the studs in the wall). The vanity side walls arrive nicely ...
0
votes
1answer
9k views

What are some cheap ideas to smoothen the surface of a papier mache? [closed]

I did a papier mache sculpture and I want to smoothen it. The end result of my paper mache has creases in it. I want an end result to be finished like it was done in wood, plastic or any solid smooth ...
0
votes
1answer
159 views

Which pH should I aim for when neutralizing restored/refinished antique surfaces?

I have recently used different chemicals to restore, refinish and treat various types of wall and millwork surfaces. E.g. I have stripped old paint using Peel Away 1 from plaster and antique millwork,...
0
votes
0answers
26 views

Is there a big difference between specialised wall smoothing pastes and joint filler/finsiher?

I have been renovating some interior walls that were damaged through age and the process of removing wallpaper. I didn't want to replaster, and I wanted a very thin covering, so I opted for a big-...
0
votes
1answer
32 views

Mineral spirits not drying on unfinished hardwood floor (12 hours later)

I'm looking for suggestions on how to dry down or remove excess mineral spirits from our unfinished hardwood floor. We installed new, unfinished hardwood flooring (yellow birch), sanded it and then ...
0
votes
0answers
186 views

Put polyurethane on marble?

Is it ok to put polyurethane as a protective coating on a marble countertop? I want to protect the marble from scratches and staining by foods and other kitchen hazards.
0
votes
0answers
17 views

Identifying/removing mystery finsh

I have a pre-1990 Mayline Ranger Drafting Table, with a mystery finish, under the rubber mat. It's soft and sort of sticky in places. It appears thicker in some spots too. Some of it comes off easily ...
0
votes
0answers
36 views

Desktop for Custom Space

I had a space to put my workspace that is kind of unusual, very long, I had a desk built, but the finish on it is a joke. I went to Ikea to see if I could buy one of their custom desktops (prefinished)...
0
votes
0answers
39 views

Mantel clock frame finish repair

I have a mantel clock which had mildew damage. I been working on getting mildew off. To restore it to its original color as seen in right part of frame below, would I need to sand and stain it? I know ...
0
votes
0answers
95 views

What finish type is most often used for furniture drawer interiors?

I recently completed building a cabinet drawer to convert a free standing vanity into a dresser. I'm aware that drawer interiors are often left unfinished, but it's quite humid where I live and I ...