Questions tagged [chuck]
The chuck tag has no usage guidance.
16
questions
0
votes
0
answers
184
views
Remove stubborn drill press chuck
I have an old craftsman drill press. Model #113.213090:
and I've noticed the chuck that I have with it really starts to slip off drill bits, even if I try to crank it tight. So anyhow I went to ...
- 211
3
votes
3
answers
2k
views
Tricks for fitting a 7/16" bit into a 3/8" drill?
I have a 3/8 hand-held drill and that's pretty much all I need for my projects. But now I have a project where I have to insert large dowels, and they will need a 7/16" hole. I don't have that ...
- 132
0
votes
3
answers
441
views
Drill bit stuck behind chuck
I am a first timer user of a drill and didn't use the proper drill bits. I removed the chuck and put the drill bit where the chuck is located and now the drill bit is obviously stuck. Any suggestions ...
0
votes
2
answers
252
views
How do I remove a chuck that got stuck during removal?
I was in the process of removing a keyless chuck on a cordless drill. I removed the screw from the chuck first and for some unknown reason managed to close the teeth on the chuck without inserting an ...
- 11
0
votes
0
answers
88
views
Hilti TE2 locked without bit
I’ve got a Hilti TE2 and am unable to put the bit in. I think I might have accidentally locked the chuck without a bit in it and now unable to unlock it to put the bit in.
Any ideas?
- 1
0
votes
1
answer
59
views
Chuck for a Dremel
Having purchased (and loving) a Dremel 4000, I decided a chuck for different sizes of small drill bits would be a good addition. Bought a couple, but neither appears to have the same thread as the ...
- 5,058
2
votes
0
answers
271
views
Why does a Keyless chuck sometimes stick?
I noticed that Keyless chucks in cheap drills tend to become stuck often, but I've always wonder why does this happen.
Is it due to overtightening the chuck?
Are low quality drill bits a factor to ...
- 121
4
votes
1
answer
2k
views
Is it normal for drill bits to slip in a keyless chuck when binding in metal?
I'm trying to drill some 5-10mm holes in 1-1.5mm thick steel. I'm using a DeWalt DCD777 18V cordless drill with Bosch HSS bits (which claim they're made for drilling into metal). Both the drill and ...
- 144
4
votes
4
answers
17k
views
Adapter: 1/8" Dremel shank to 1/4" chuck
Situation: I have a Dremel rotary tool with normal 1/8" shank and a Dremel Multi-Vice.
Need: I wish to attach this Dremel tool (with standard 1/8" shank held stead with my Dremel Multi-Vice)...
- 305
3
votes
2
answers
1k
views
How do I remove this keyed Jacobs drill chuck?
I have an old Jacobs keyed drill chuck in my box-o-spares, and I need a drill chuck for my hobby lathe. I have a suitable tailstock arbour, but the drill chuck has something already installed, and I ...
- 9,739
0
votes
1
answer
548
views
How to further disassemble cordless drill/driver chuck?
I've completely disassembled cordless drill/driver Black&Decker EGBL188 H1 10mm, except this chuck, as seen in the pictures.
I've tried pulling out the plastic piece: I've put the chuck facing up ...
- 111
1
vote
2
answers
10k
views
How to remove an old bosch drill chuck?
I've got an old Bosch corded hammer drill, model PSB 500. It's not the "RE" (reversible) model. The chuck is a traditional one with the jaws and the key to loosen and tighten the bits.
Since this ...
- 11
0
votes
1
answer
2k
views
What size chuck key do I need for my Black & Decker DNJ62 drill?
I have been given an ancient Black and Decker DNJ62 power drill from my father (who knows even less about DIY than I - which is saying something). Unfortunately he has lost the chuck key for it, ...
- 133
0
votes
2
answers
85
views
Increasing the Maximum Shank Dia [closed]
There is a device in my head that I know must exist, but I can't seem to find it.
I own a drill. Kinda small. It has a small chuck so the shank dia of the drill bits that I can use is limited. Is ...
- 23
2
votes
1
answer
622
views
How do I adapt my spiral ratcheting screwdriver to use with all bits?
I have a spiral ratcheting screwdriver like the one shown below. I want to adapt it to use with all kinds of bits. This basically means putting a 1/4" hex socket on the other end.
Fig.1. Yankee ...
- 335
1
vote
2
answers
10k
views
Bosch PSB 650 hammer drill chuck won't tighten [closed]
I was using my hammer drill and wanted to change the tool but it now looks like the chuck won't tighten to hold any tool. The motor is still working fine but can't use it as can't attach anything to ...
