Questions tagged [carpentry]

The tag has no usage guidance.

Filter by
Sorted by
Tagged with
0
votes
0answers
32 views

Sill Plate not Lining up with Foundation Wall [duplicate]

I am in the process of building a one level home in PA. After the formed concrete walls were poured and the framing began, I noticed that on one side of the house that the sill plate was flush with ...
2
votes
2answers
861 views

What type of Drill should I go for?

I am planning to build a new Computer table and a book shelf by myself. I will require a drill machine that can drill a hole into wood and that can also drive a screw into this hole (using the drill, ...
0
votes
0answers
102 views

How to properly hire contractor(s) to fix deck and railing deterioration?

During home inspection while buying our place the inspector underestimated the cost of the job to fix rot that got inside the railing on a tiny (~3'x3') balcony/deck. He said it would cost ~$1000 to ...
1
vote
3answers
2k views

Fix sagging beam situation

We've got a beam that we replaced two years ago due to some damage. The beam is out front and is above all the other beams it supports, which makes the whole thing a bit strange. We made our own ...
1
vote
2answers
732 views

Do I really need a newel post at every change in direction in a banister?

I'm constructing a banister for a loft. It's an area with three angled turns - labelled A, B, and C in this picture: I know the conventional wisdom is that you need a newel post at every change in ...
2
votes
3answers
74 views

Building a ledger for indoor use with with some cut to size 2 by 4s, should I stain or paint them?

I'm builduig a ledger for indoor use (to support a work surface) with with some 2 by 4s cut to size, my question is, should I stain or paint them to protect them? for spills etc, or is staining indoor ...
1
vote
2answers
1k views

What is a good reference book for cabinetmaking and/or other millwork?

I'm interested in making some cabinets and shelving. I have basic carpentry experience but have never tackled a project like this before. I'm looking for a good, illustrated guide to making cabinets ...
3
votes
1answer
1k views

What is the easiest way to measure an irregular floor space?

I would like to order a comfort mat for the floor of a small kitchen. The company can make it to order but I have to provide exact dimensions. This is harder that it sounds though as the floor space ...
1
vote
2answers
15k views

How to attach ledger board to under-roof siding?

I want to attach a ledger board, over the existing wood siding. Something similar to this, but immediately underneath the roof How do I determine where I need to drill the holes to attach it to the ...
0
votes
1answer
88 views

Problem with Screws/Hinges on laminate door

Fitting a finished laminate door. Routered hinges and pre-drilled before screwing. Screws nearest the edge of the door caused a ripple as if screw was pushing it the laminate out. checked screws were ...
1
vote
1answer
423 views

Hole in the floor

I bought an older house and it has a rectangle hole in the living room. It is covered with the register and it looks like an intake. I don't fully think it was used as an intake as the furnace is on ...
2
votes
3answers
1k views

How can I prevent my dining table from tilting?

I am building a dining table similar to this one - The problem, if you apply some pressure, the opposite ends lift up. In fact, that box underneath itself lifts up. One way is to add a big plate ...
0
votes
1answer
479 views

Is this ladder bookcase design strong enough to hold printers?

I have been looking for a shelf system to store my printers and other misc. items next to my desk. After looking around at various hardware stores, office supply stores, Ikea, Amazon, and even second ...
7
votes
1answer
2k views

Broken step on staircase

We have a broken step on our carpeted staircase. How can I remove then refit the carpet without damaging it? When the carpet has been removed, I will have to repair the step if possible, then refit ...
3
votes
1answer
753 views

How to join two 1x6s to form a 23' baseboard with a seamless transition?

My upstairs hallway is 23' long and one of its sides has no doors on it, meaning the baseboard on that side covers it continuously. I am using 1x6 poplar for baseboard and the longest piece my local ...
20
votes
17answers
237k views

When installing hardwood floors, should I use rosin paper, roofing felt, or nothing underneath? Why?

I've installed hardwood floors, over top of OSB subfloor with a layer of roofing felt in between. I copied this from the hardwood floor contractor who did a kitchen in my home once. He'd been in ...
2
votes
5answers
156 views

Improving piece of furniture

I have a piece of furniture that is in need of some improvements. This is the piece: As you may already see, there are a lot of light marks in it. If we look closer to the surface, this is how it ...
4
votes
3answers
3k views

Are there any good videos available that teach basic carpentry?

I apologies if this was already covered but I could only find a thread on books, and it was geared towards someone having some basic skills already. While I am far from useless, I never had a reason ...
2
votes
1answer
6k views

How to fix a racked/sagging exterior wood entry door?

My old 3-unit condo has a nice old wooden entry door, with 3 horizontal rails and 2 vertical stiles, with a single large pane of beveled glass as the top panel. The door is very similar to the one ...
0
votes
1answer
2k views

Repairing a gap under a eave.

Last night I heard scratching in the wall and upon investigation found that a squirrel had managed to knock loose a piece of wood (I assume as there was no covering to be found) in the eaves where one ...
6
votes
4answers
3k views

How can I build a screen door?

I have a guesthouse with an unusual door, 32" x 76", and it needs a screen door. Home Depot has tons of cheap-o screen doors that could be cut down to maybe 32" x 78" safely, but an additional two ...
0
votes
0answers
32 views

How to correct the inclination of an old chair

I have an old easy chair, which I'm thinking to polish and use it. The chair is made of teakwood and has nut and bolts at the joints. As it is decades old and was unused for a long time, the holes at ...
0
votes
1answer
490 views

how to design and buy materials for breakfast bar/standing desk?

My girlfriend has given me an assignment: build a breakfast bar for the corner of the kitchen, with a tabletop that is 55" by 13". We would buy two stools to go with it. She wants me to build it ...
0
votes
1answer
6k views

Is it code-compliant to attach a patio to the roof like this?

I want to attach a patio cover to my house. Trouble is the clearance between the window and the roof rafters is too small for a ledger. I was considering the option of attaching to the roof top like ...
2
votes
5answers
10k views

How do I sharpen wood lathe tools?

I've had a lathe for about a year now (I have the JET 1442 with variable speed) and love it but noticed that I really suck at keeping a nice sharp edge on my tools. I have a small bench grinder I use ...
1
vote
1answer
6k views

1“ x 2” Furring Strips for Drywall Ceiling

In my basement, there's currently a tile ceiling that's installed on furring strips attached to the joists. The furring strips are 1"x2", attached to the joists by nails. We're currently replacing the ...
3
votes
1answer
545 views

How do I build a headboard for a bed?

I need to build a headboard in the next couple of days. My requirements: can be attached to the wall, I read something somewhere about French cleat needs to be attached to the bed, to stop the bed ...
2
votes
2answers
3k views

Is it necessary or recommended to kerf baseboard?

I've been told that baseboard, unless done so already by the sawmill, should be kerfed before installation to prevent warping in the future. Is that really necessary or just a good thing to do? I ...
14
votes
5answers
47k views

Should I attach the fence post(s) where my fence meets my house? How do I do it?

I'm going to be building a 6 foot tall cedar privacy fence in the spring (with pressure-treated posts) and need to determine what to do with the two posts that meet the side of my house. In order to ...
1
vote
2answers
1k views

Easiest way to build an oddly-shaped shelf for cabinet above stove

In my rented apartment, there is a cabinet above the stove which cannot be used for storage - the stove exhaust fan is sitting there. The first photo shows the doors closed with an 18" ruler for ...
5
votes
1answer
38k views

How can I estimate the load capacity of a set of shelves?

I'm pricing and researching supplies for built-ins in my living room. The plan is cabinets on the bottom, a cubby for a TV and staggered shelves for several hundred HEAVY books above that. My ...
3
votes
3answers
6k views

How to repair a closed-stringer staircase?

I need to replace the treads on my closed-stringer staircase. They are 100-year-old softwood with unsightly, disintegrating rubber covers glued on. One stringer is against the outer wall of the house, ...
4
votes
1answer
1k views

How can I know if a self-designed structure I build will be structurally sound?

I've recently begun designing and building structural updates to my house. For example, I've built some shelving units and a cabinet space. Everything has gone well so far, but I'm about to tackle ...
1
vote
1answer
55 views

Hidden fasteners for 1/2" spacing between decking boards?

I want to build a screen out of 5/4 x 4 ipe boards with 1/2" spacing, using some sort of hidden fasteners. All the hidden fastener systems that I was able to find so far are designed for decking, and ...
2
votes
1answer
3k views

Re-glue plastic edge banding on a desk

I have an office desk with a semi-circular section (to sit at) where the edge banding has come away from the wood. The edge banding is fairly thick (1-1.5mm) and rigid, so it takes a fair bit of ...
1
vote
2answers
12k views

How to build a quick-and-easy wood ladder?

I have a pair of long 4x4 posts holding my chimney, and I'd like to build a ladder in to the posts for maintenance. In some ways this could be safer than using an extension ladder, as the posts are ...
0
votes
1answer
632 views

How do I build wall-mounted shelves?

I've spent the past few months getting my flat renovated, and would now like to build some bookshelves across two of the walls in my living room, and around the corner that joins these walls. The ...
1
vote
1answer
505 views

advice for cantilever on temporary, free-standing wood structure

My daughter wants a piñata at her 6th birthday party. Unfortunately our back yard has no convenient tree limbs or other ways to hang the piñata, so I want to DIY something to hang it from. I'd prefer ...
2
votes
5answers
687 views

Decent Brand Names for Beginner Carpentry

I have done a few small projects but nothing too extravagant without a table saw. I would like to get more into woodworking but the one tool I don't have right now it's a table saw. All the rest of ...
-2
votes
1answer
3k views

What type of replacement windows can I use on my log home?

I'm stumped as to what style of window to pick for my log home (replacement). The current windows are aluminum frame, and are trimmed flush on both sides with wood, so all you see is a very thin strip ...
5
votes
4answers
75k views

Which nails should I use for shoe molding installation?

I'm about to install shoe molding all over my house. The baseboards are hung for carpet, but we're replacing the carpet with vinyl. So I have a pretty good sized gap to cover. I'll probably use 11/16 ...
1
vote
0answers
573 views

How do I hang a 500lb bed swing?

Could someone please tell me what kind of support is needed to hang a 500 pound porch bed swing? The 500 pounds also includes the weight of people on the swing.
2
votes
1answer
1k views

Is it better to stain before or after assembly?

I'm going to build a wrapping-paper cart: it holds rolls of wrapping paper, ribbons, tissue, bows, scissors and tape, etc. It's going to be mostly made of 3/8" plywood, and will have a couple of ...
0
votes
1answer
603 views

What should I consider when designing a simple bookcase that will be built without power tools?

I'd like to build a bookcase using pine (or meranti) planks of dimension 22mm/220mm/3m that my local hardware store stocks. They offer the service of cutting to length, but I have no power tools (well,...
0
votes
2answers
4k views

How do I make built-in bookcases for the corners of a room?

I am planning some built in book shelves around a room. The issue I have is what to do at the corners of the room. That is, how not to waste space, but to make the space useful. The corner space ...
3
votes
1answer
3k views

How can I repair a dining room table with folding ends?

If so, I've got a nice old dining room table that folds down quite small (seats 2) but also can be pulled out with leaves to seat ~8. The ends of the table are supported by swing-out arms that are ...
0
votes
1answer
1k views

What is the technical term for this corner cupboard?

I am trying to learn what this small blue cupboard on the left side of the table is called? It's a corner cupboard but I am not sure what the technical term is:
3
votes
2answers
2k views

Should I pre-built rafter units, or build them in-place?

I'm planning a small roof - 12' x 16', gable style. Almost all the rafters will identical. Should I build rafter units ahead of time? 2 rafters + a ceiling joist + plywood gussets. I'd make a simple ...
1
vote
3answers
942 views

What information do I need to size a sawn or hewn beam?

I have a load bearing wall in my house that a previous occupant decided to cut a hole in to make things feel more open. They did not add a header, much to my chagrin. I'm planning to put an exposed ...
6
votes
1answer
5k views

How to stop a circular saw from locking?

I've been using my new circular saw for about a week. Today while making a plunge cut it just locked. It didn't get stuck on anything inside the board and it consistently locked every time I tried to ...