Questions tagged [carpentry]

The tag has no usage guidance.

23 questions with no upvoted or accepted answers
Filter by
Sorted by
Tagged with
2
votes
0answers
173 views

Melting snow on the deck leaked into the house. Is my deck flashing incorrect or insufficient?

Last fall I had a small deck built to replace three masonry stoops that were falling apart. The sheathing behind the stoops was not flashed and was rotting. The contractor did a good job as far as I ...
1
vote
0answers
36 views

Sheet metal behind drywall…why?

I’m trying to install a niche by my bathtub. when i cut into the drywall which is on an exterior wall there was a full sheet of metal behind the dry wall. it runs the length 60 inches and height 6 ...
1
vote
0answers
29 views

Best option for replacing rotting redwood exterior trim

I have 12” painted redwood fascia boards rotting in places, and I'm looking for a smooth board to replace it with. Exterior kiln dried treated and primed pine has been suggested but would have to be ...
1
vote
0answers
90 views

Strengthening a Bamboo Ladder (After a Mistake)

I am a newbie to this so please be gentle. I had some dried out bamboo lying around and for some reason, I decided to make a ladder out of it. I got one of my measurements wrong and cut out a notch ...
1
vote
0answers
212 views

How do I support a deck-style floor in crawlspace?

This question is kind of a follow-up to the one asked here: how-should-i-add-flooring-in-my-crawl-space. My crawlspace is exactly as the one described. Basically my house is on a slope and have a ...
1
vote
0answers
377 views

Closing severe gap along baseboard and floors

We have very unleveled floors along this wall that wood paneling is going up on. The wall is about 10ft long and there is almost a half inch difference in the height of the floor. The baseboard was ...
1
vote
0answers
573 views

How do I hang a 500lb bed swing?

Could someone please tell me what kind of support is needed to hang a 500 pound porch bed swing? The 500 pounds also includes the weight of people on the swing.
1
vote
1answer
322 views

How to attach beadboard to plaster walls without blowing out nails?

I am replacing old beadboard on our plaster walls. Around the windows there seems to be cement under the plaster. No matter if I use a nail gun, panel screws, nothing will penetrate the cement. The ...
0
votes
0answers
64 views

Is it normal for an experienced Finish Carpenter to put so many blemishes on walls during a kitchen cabinet install?

I recently hired a Finish Carpenter with “30+ years of experience” to install my white finish, plywood cabinets. I paid $1400 for him to mount 10 boxes (he only mounted 9 but still charged $1400 plus ...
0
votes
0answers
89 views

Cam lock & dowel alternatives

I have a chest of small chest of drawers held together by metal cam lock & dowel pegs. The cam lock & dowel regularly come loose. I am looking for suggestions for alternatives? the cam lock ...
0
votes
1answer
61 views

Help identifying the type of shelf support

please could someone help me identify the type of shelf support in the pic below. This is from a kitchen cabinet shelf, need to order some spares, but can't find anything that resembles it online. ...
0
votes
0answers
268 views

Untreated pine wood - do I really need to treat it? (indoor usage)

I have a piece of furniture which is made from raw pine wood. It has relatively fine sanded surface and I like that it is not sealed or stained. What if I just leave it so, i.e. do not apply any seal ...
0
votes
1answer
142 views

I tightened a Titus Minifix Cam too hard and now I have to take it apart. Is that OK?

I put together this TV stand, and used a cam/bolt dowel for the first time when I got to the step of attaching the top of the TV stand (A) to the two stand panels (E). Since I assumed the cam had to ...
0
votes
0answers
179 views

fascia compound angles

Alright so hopefully I can explain this properly. I'm replacing a fascia board where the corner can't be a straight cut. There is one board that spans the "bottom" of the roof and one that goes up ...
0
votes
0answers
38 views

How to install a vinyl fence gate on a pool deck?

I am trying to install a vinyl fence between a deck and the pool in a backyard. The homeowner wants the fence (Wam Bam Vinyl Fence system) to run the width of the backyard until it gets to the deck ...
0
votes
2answers
377 views

What's the proper height above a subfloor, for an exterior inswing door threshold? Carpet? Tile? Hardwood?

I need to build a custom door threshold for an in-swing exterior door where there's no exterior overhang or porch. At the moment there is only subfloor, no finish floor. How high above the subfloor ...
0
votes
0answers
105 views

How do I get the most out of cracked lumber?

I'm about to build my first* large project with real hardwood, and because random widths and lengths lumber is so much cheaper than standard cut lumber (and typical cut lumber sizes are often not even ...
0
votes
1answer
87 views

Window Stool meeting metal window frame

Our house had no window stool on one window, just a space. I have one in progress but am unsure how to have it meet the metal base of the window, onto which the window itself rests. I don't see any ...
0
votes
2answers
2k views

Install a recessed medicine cabinet with stud problems

I have a space determined for a recessed medicine cabinet. When I cut a peephole in the drywall, I determined that the closest stud on the left is 6" from the left edge of the recessed area. On the ...
0
votes
0answers
102 views

How to properly hire contractor(s) to fix deck and railing deterioration?

During home inspection while buying our place the inspector underestimated the cost of the job to fix rot that got inside the railing on a tiny (~3'x3') balcony/deck. He said it would cost ~$1000 to ...
0
votes
0answers
32 views

How to correct the inclination of an old chair

I have an old easy chair, which I'm thinking to polish and use it. The chair is made of teakwood and has nut and bolts at the joints. As it is decades old and was unused for a long time, the holes at ...
0
votes
1answer
44 views

T-Nuts for Granite/Plywood table?

I have a 30"x50"x3/4" granite slab that I would like to use for a table. I'm thinking of putting 5/8" plywood underneath (20"x40"?) and before mounting the granite on top, inserting a few T-Nuts for ...
-2
votes
1answer
3k views

What type of replacement windows can I use on my log home?

I'm stumped as to what style of window to pick for my log home (replacement). The current windows are aluminum frame, and are trimmed flush on both sides with wood, so all you see is a very thin strip ...