Questions tagged [abs]

The tag has no usage guidance.

Filter by
Sorted by
Tagged with
7
votes
2answers
16k views

What is 'Cellular Core' or "Foam core ABS' pipe?

At a big home store today, all the black drain pipe was 'cellular core ABS' in 'schedule 40'. What does the 'cellular' mean? The pipe was very inexpensive.
3
votes
2answers
2k views

Purple primer left on over night: can I use it?

I am using Oatey purple primer with Oatey medium gray pvc cement. This is a 2 inch PVC pipe job for pool pump to filter. I have a joint where I applied purple primer then realized I am not ready for ...
2
votes
2answers
3k views

ABS Glue = yellow or black?

I'm doing a bunch of ABS plumbing for the first time. I have everything cut and ready to assemble so do one last YouTube search for a few tutorials on glueing. Seems really simple. HOWEVER, all the ...
1
vote
2answers
43 views

PVC to ABS Recommendations

Under my kitchen sink is an ABS pipe going into the drain. I need to shorten it, because the disposer is moving to the right side of the sink, and this pipe with Y-connector will be in the way. (the ...
1
vote
1answer
834 views

Can dryer vent touch ABS pipe?

I am installing a dryer vent (using rigid aluminum vent). The vent will be running along the same path as a 1.5" ABS pipe (which is used as drain vent, so no water flows through it). Would it be a ...
1
vote
2answers
103 views

Fernco coupling to join ABS drain pipes under basement?

I tapped into a 2" ABS pipe that runs underneath my concrete basement floor, and presently joined it using a Fernco coupling allegedly rated for underground use. (Unclear if this can be used indoors ...
1
vote
3answers
2k views

connect 3 inch ABS pipe to only 0.5 inch exposed pipe

I would like to cut an existing pipe and install a coupler to connect 2 pieces of 3 inch ABS. I would like to make the connection where I am pointing on the image. Is that enough pipe to connect to (...
1
vote
1answer
1k views

Question about running new drain pipes in Laundry room

Hi I just framed out my laundry room in my basement and I'm looking to run add a utility sink and I need to add a drain line for both the washer and the utility sink though the utility sink is going ...
1
vote
2answers
75 views

Are all plastic compression fittings interchangeable?

I need to rework the plumbing under my kitchen double sink. Currently, it consists of one brass drain pipe along with all ABS pipe and compression joints. Can I replace the pieces I need with their ...
1
vote
2answers
1k views

Recommendations for drilling a lot of small holes in various plastics (ABS/PVC/Acryl)

I need to drill a large series of 2 millimeter holes (several 100) in pieces of plastic that vary in thickness between 16 and 22 millimeter. The plastic will be ABS, PVC and acryl (not sure if that is ...
1
vote
0answers
28 views

Abs shower drain wtih 2 90° elbow to p-trap in shower drain

I am rebuilding shower, and i have a little issue with drain, I need to move it back and to left, the only way to do it as I figured it out it's to put 2 90° degree elbow together than in to p-trap,I ...
0
votes
3answers
2k views

How can I attach 1 3/8 pipe to 1 1/2 inch abs?

I am trying to install a new vanity and the age of my house is killing me. The pipe coming out of the floor is 1 3/8 inch pipe. I have a new sink drain that is 1 1/4 inch so I have a trap adapter for ...
0
votes
1answer
78 views

Connecting ABS at <22.5 degree angle?

I’m trying to get my plumbing vents up into my roof joist bays. They’ll run halfway up the house until they hit a beam. I’m then going to level off the vents so they dip below the beam and connect ...
0
votes
1answer
189 views

Remove ABS P Trap

Related I have an ABS p trap that doesn't seem to have any union nuts. Where my finger is pointing is the tail piece nut that I can loosen (and probably remove), but the rest of the p trap doesn't ...
0
votes
3answers
135 views

Can I glue a sleeve over a cracked dishwasher inlet line on my brand new garbage disposal unit?

The disposal is brand new and I can't return it even though it was damaged in shipping, as I'm well outside the return window. I believe the inlet is ABS plastic, as it's stamped with a small number 2....
0
votes
2answers
66 views

How to fix broken plug

My neighbors landscaper has totally mutilated the cleanout plug between our yards that connect to each other. Can I use a brass plug in the ABS pipe, or should I use ABS to ABS. (4" pipe) whatever I ...
0
votes
2answers
2k views

How do I repair this friction ABS kitchen sink pipe fitting

I have an ABS pipe fitting under my kitchen sink which appears to be held on by friction (white piece just above the p-trap). After the p-trap the pipe makes a long run to the left where it's not ...
0
votes
1answer
136 views

What size are the correct fittings for 1 1/4" ABS pipe?

I need to plumb into an existing ABS drain, labelled as "ABS/DWV 1 1/4" schedule 40 ", but for the life of me cant find any 1 1/4" fittings!!! My suspicion is that the pipe is 1 1/4" ID, and I need ...
0
votes
1answer
56 views

Sewer Line Clog suggests pipeline replacement

Our 1963 in-city home has occasional sewer line blockages. Renting a power snake for $30/half day has gotten old. The city has scoped the line and suggest the constriction in diameter occurs 40 feet ...
0
votes
2answers
579 views

Would it work if I glued a new closet flange to an existing closet flange?

abs closet flange is 1 and half inch lower than floor. the flange inlet is ID 4 inches. I am thinking of use some abs cement to glue a new abs flange into the existing one. (I assume 4x3 flange can go ...
0
votes
1answer
26 views

10' PVC Schedule 40 vs ABS sun sail support post. Life expectancy, wind and UV damage

I'm setting some 6' T-posts deeper then usual ( down to like 4') for a simple fence project and i have a few spots where i want set up sun sail triangle from 10' high to 8' in about a 15' x 15' area. ...
0
votes
0answers
80 views

Can an ABS drain be fitted to a PVC waste pipe riser?

The only shower drain available at my local hardware store is The Wondercap, which looks fine. However, the (white) plastic is formed with "ABS", and the drain pipe itself is white plastic, which I ...
0
votes
1answer
704 views

ABS offset toilet flange dilemma. Suggestions to make my 11“ rough-in into a 12” rough-in. USA

Recently I started a thread to get advice on how to move a flange for a toilet so that I can wind up with a 12" rough-in when I'm done. It's problematic since I can't really work with the ABS under ...