I have 2 wall switches. 4 wires coming out of ceiling (black-hot, red-hot, white-common, bare- ground), a ceiling fan and a remote. How do I wire them and still be able to use wall switches?

I can wire the ceiling fan and just leave the red wire capped with a wire nut, but that leave a useless switch in the wall. The ceiling fan that was up before had a remote and the switches on the wall worked ( 1 switch had to be on in order for the remote to work, and the other controlled power to the fan). How do I wire it back like this?

  • Are the switches in the same or different locations? – bib Jul 8 '14 at 12:07
  • Just a word of caution that if your fan speed and light dimmer are only controlled by remote, (no pull strings), then bypassing the receiver will not permit you to control your settings. (I'm looking at you "Turn of the Century" fans.) – user55747 Jun 28 '16 at 15:12
  1. Start by turning off the power at the breaker, and verifying it's off with a non-contact voltage tester.
  2. Connect all the bare or green grounding conductors together.
  3. Connect the white wire from the ceiling to the white wire on the input side of the remote receiver module and the white wire in the fan.
  4. Connect the black wire from the ceiling to the black wire on the input side of the remote receiver module.
  5. Connect the blue wire from the output side of the remote receiver module to the blue wire in the fan.
  6. Connect the red wire from the ceiling to the black wire in the fan.
  7. Cap off the black and white wire from the output side of the remote receiver module.

Now when one switch is on, the remote will control the light. The other switch will turn the fan on and off. You'll end up with something like this.

Wiring Diagram 1

Alternatively, you could wire it like this.

Wiring Diagram 2

This way the remote module will control the fan (when the switch is in the ON position), and the other switch will control the light.

This answer assumes the black wire controls the fan, while the blue controls the light kit on the fan. Check the documentation that came with the fixture, for proper wiring instructions.

  • So the white wire on the receiver is capped? And the blue wire coming out of receiver is capped? – user38908 Jun 27 '15 at 22:35
  • @user38908 The blue (or black depending on how you want it) coming out if the remote module would be capped. You could use the white (neutral) coming out of the receiver, or the one coming out if the ceiling. It's up to you. If you don't use the one coming out of the receiver, then yes it should be capped as well. – Tester101 Jun 28 '15 at 0:40
  • This worked out great - thank you. The fan instructions said nothing about using two switches, so this really helped. After I got it all working an understood the wiring, I ended up removing the remote module all together and wiring it al up directly from the ceiling wires. Black to black and white to white so one switch controls the motor (installed a Lutron fan switch to get the speeds), then red to blue so other switch controls the light (installed elution light dimmer). Love the set up. Thanks again. – Michael Andrews Nov 3 '20 at 13:00

For my switches to work, once I connected the blue wires for the lights together, I also had to connect those two blue wires to the black wire coming from the ceiling in order for the light to have power.


This was helpful to understand the red from ceiling but to get my remote to work fan and light functions while wall switch was on I had to wire like this: red from ceiling to black of receiver, black from ceiling capped, white from ceiling to white of receiver and light/fan, yellow from receiver to black of light/fan, blue from receiver to blue of light/fan


This is a very helpful site. My setup is like user63515: remote has black & white on input side; blue & yellow output side. House has black, white, & ground wires. Connected black input to black house, white input to white house & white light/fan, blue output to blue light/fan, and yellow output to black light/fan. One wall switch powers entire fan. Make sure fan is on by pulling chain. Remote control now controls fan speeds and the light!


(C) Ceiling / ac supply: white, black & Red

(RI) Receiver In: white, blue & black

(RO) Receiver out: white & black

(F) Fan: white, black & blue


  • C white & RO white
  • RI white & F white
  • RI black & F black
  • RI blue (alone)
  • RO white & C white
  • RO black & C black
  • C red & F blue
  • Hello, and welcome to Stack Exchange. It's really hard to understand what you mean; some formatting and verbs could really help. – Daniel Griscom Jun 1 '18 at 22:41
  • For those using a Minke Air fan and remote with two switches - this works – Betsy Dupuis Aug 2 '20 at 0:53

I installed a hunter fan that utilizes the remote which had a different set up from the other poster. The image below is how I did it and it works perfectly for utilizing both switches. One switch turns on the fan directly and the other provides power to the fan where you use the remote to adjust the speed.

Important Note: The fan remembers your last setting so you might have to wire it per the manual and turn on the light first through the remote.



I did this last night at my condo. The fan is a 2018 Hunter remote, no chains. I wanted to be able to change the fan direction and speed, so I had to use the remote for that. I wanted the light to be controlled from 2 3 pole switches. The switch situation is: single 3 pole by garage entry door. Double switchplate housing a single pole on the left and a 3 pole on the right as you look at it, at the living room/kitchen entrance. Red from ceiling to black from fan and black out of remote. Black #1 from ceiling to blue from fan. Blue from remote is capped off. White from ceiling to white on remote and white from fan all together. Copper from ceiling to all greens and yellow out of remote. Black #2 from ceiling to black into remote. Works like a charm. A check of the 3 pole next to the single pole under a double switchplate revealed black as the traveler connected to two screws on the 3 pole.

Not the answer you're looking for? Browse other questions tagged or ask your own question.