When wrapping pipe threads with teflon tape (thread seal tape), what is the direction and recommended number of times to wrap the tape around the threads? Any other recommendations or tip/tricks when applying teflon tape?

6 Answers 6


Wrap clockwise - i.e. in the same direction as the tightening action of the nut. This means that you are also tightening the tape around the thread.

If you wrap anti-clockwise I find that the tape bunches up and comes away.

As for the number of layers - I usually wrap the tape around at least twice, maybe even three or four times.

  • 2
    @Doresoom - I always have to think about this. I wish I could get it right every time!
    – ChrisF
    Commented Nov 15, 2010 at 14:32
  • 7
    Just use the right hand rule. If the end of the pipe is facing you, point the thumb of your right hand down the pipe and curl your fingers into a fist. The direction your fingers curl is clockwise. Either that, or you need to go to a hospital because your hand is broken.
    – Doresoom
    Commented Nov 15, 2010 at 14:35
  • 1
    re: wrapping twice, thanks for the advice. Elbow joint on my dishwasher intake was giving me fits with a very slow leak with just a single wrap of tape. Double wrap of tape is holding so far :-)
    – leedm777
    Commented Aug 1, 2011 at 3:38
  • 1
    Just remember, teflon tape is meant to allow you to tighten the fitting more tightly, it is not meant to fill in any gaps or looseness. The teflon is more slippery than the original surface. You just need enough teflon to overlap. Anything else is overkill and could actually PREVENT a tight, leakproof fit. Commented Mar 17, 2015 at 17:55
  • 1
    @BrownRedHawk Let's be honest.... we all use it to fill the gaps though Commented Sep 8, 2015 at 16:29

For the correct number of times to wrap the tape, check the instructions on the tape package (that tiny little printing in white plastic you can barely read). It should tell you. Different manufacturers will have different specs on this (depending on the thickness of the tape).

I highly recommend the higher-density pink teflon tape. It is a tiny bit more expensive, but I have found that it stays put on the threads much better and seals better.

The pink tape I use (CFPC) says:

  • 3 full wraps for pipes up to 1"
  • 4 wraps for pipes 1" - 1.5"
  • not to exceed pipes > 1.5"

Using too much tape is bad, too little is bad.

Oh, and ditto what ChrisF said about wrapping the tape in the proper direction!

  • Good to know. I've always used WAY too much; like 20 wraps. But I've always been happy with the performance of it. This is the uber thing white stuff though. Thanks for the recommendations, I'll check the documentation next time and look for the pink stuff. Commented Dec 6, 2010 at 7:53

Personally I would recommend avoiding teflon tape altogether and use TFE paste instead. It can be a bit messy, but aside from that it's pretty hard to do it wrong - just goop the stuff on there and screw it together.

  • Is this rated to be used with PVC (plastic pipe) as well? I know some pipe dope cannot be used with plastic, because it will react with the pipe and cause future leaks and/or failures.
    – Tester101
    Commented Nov 17, 2010 at 17:39
  • @Tester101 - Not sure, can't say I've ever tried to use it with PVC or plastic fittings. Commented Nov 18, 2010 at 17:44
  • Some are OK for PVC or CPVC, but not ABS plastic. "Rectorseal T plus 2" is OK for all of the above, but "Rectorseal #5" is not. (Both are sold at my local Lowes and Home Depot.) Commented Jan 3, 2011 at 18:00

A good plumbing friend gave me a tip which is worth knowing. After wrapping the tape, run the back of a hack saw blade across the threads. This assists in the tape not slipping when you screw on your fitting


I watched a qualified person install my on demand water heater and he used the paste followed by the yellow Teflon tape. I would do the same if I had to do an installation on my own. This fellow is knowledgeable and a very good friend.

  • What paste did he use?
    – Niall C.
    Commented Oct 20, 2012 at 14:29
  • I would at least get a second opinion on this--I've heard people (who also seemed knowledgeable, to me) say that they degrade each other when applied at the same time.
    – msouth
    Commented Jun 17, 2014 at 13:04
  • I've tried using JUST paste before and it did not seal. I then tried again with JUST Teflon and it sealed great Commented Sep 8, 2015 at 16:30
  • 1
    The yellow tape is made for gas lines, not for water. Commented Sep 8, 2015 at 19:57
  • @JasonHutchinson you can use it for water - it's just a bit thicker (more expensive) that's all.
    – Ariel
    Commented May 3, 2016 at 17:53

Do it 4 to 5 wraps around the pipe Hold the fitting with you left hand and the Teflon tape with the thumb Go up first For pvc and any metal pipe use Teflon compound so u don't put too much stress in the pvc fitting

Not the answer you're looking for? Browse other questions tagged or ask your own question.