I found this in the back-corner of our second-floor closet:

power supply


Presumably this is not to code. Has anyone seen anything like this before, or have any ideas what it's for? Unplugging it doesn't seem to have broken anything, and there aren't any small electronics on any of the nearby walls.

  • 5
    code isn't too concerned with low voltage wiring, are you sure it's a problem?
    – dandavis
    Commented Sep 28, 2020 at 21:47
  • 3
    Well, the missing faceplate certainly isn't Code! As to the low-voltage side of things, can you get us clear shots (or a readout) of the printing on the low-voltage wiring? That's the determinant as to whether the LV wiring is of the proper type to be used in a wall to begin with... Commented Sep 28, 2020 at 23:34

3 Answers 3


It looks like the power supply for an old alarm system.

  • concur with @freshop, You might have the remnants of the old system hanging in a nearby closet up high or down low, possibly under a panel cover.
    – mark f
    Commented Sep 28, 2020 at 19:50
  • There is an old alarm system downstairs, so this is probably correct. Commented Sep 29, 2020 at 11:21

Nobody mentioned door-bell.
Many electrical doorbells use a AC transformer with output anywhere in the 5 to 20V range.
9 and 12V AC are most common.

  • 8
    @Criggie Several years ago my father janked several yards of thin 2-lead wire from behind the drywall when he re-modeled his hallway. He thought it was old alarm-system wiring, no longer used. It wasn't until several days later when someone was at the door he realized he destroyed the door-bell. Of course the walls had been re-done by then. Now he has a wireless door-bell :-)
    – Tonny
    Commented Sep 29, 2020 at 12:47
  • 1
    Doorbell transformers are generally 16vac Commented Sep 29, 2020 at 15:20
  • 2
    @batsplatsterson That is very location specific I think. Here they almost exclusively 12 Vac and the few that are not are 9 Vac. Some very old ones (30+ years) are 8 or 10 Vac. I have never seen a 16 Vac.
    – Tonny
    Commented Sep 29, 2020 at 15:24
  • 1
    Well, the outlet in the picture is clearly a US-style, and OP's profile seems to imply that as well. (Could be Canada, but it'd be the same thing there.) Commented Sep 29, 2020 at 16:53
  • 1
    In the USA, 16VAC is the most common but can also be lower (8VAC) so you dont get "buzzed" or 24VAC (uncommon), this is what I have heath-zenith.com/products/… Commented Sep 30, 2020 at 0:11

I agree it's likely this is an alarm system power supply, I know Honeywell had some 9VAC panels and likely others.

Believe it or not it may be code compliant, the rules for class 2 wiring are pretty loose. It's not really workmanship anyone would brag about but it's a pretty common hack.

If the cable is suitably rated CL2 or better it's compliant. However it looks like a zipcord which is not likely rated for installation inside walls on class 2 circuits. However, at 9VAC, it's not much of a hazard.

  • Note that even if it's nominally 9V, there's absolutely nothing there that instills confidence that a short on that red cable won't get 1000A going through it. The irony would be if it were supplying power to a /fire/ alarm, particularly if its standby batteries were long dead. Commented Sep 29, 2020 at 13:39
  • @MarkMorganLloyd the only way a transformer of that size could supply 1000A would be if the input were shorted to the output. And then you'd have even bigger problems. Commented Sep 29, 2020 at 14:35
  • 1
    I think @MarkMorganLloyd may have been thinking about a short from a 120V line to the low voltage line, like if a nail or screw were to pass through both of them. Commented Sep 29, 2020 at 14:38
  • Actually, I saw MADE IN CHINA and at that point ceased making any assumptions whatsoever regarding what's in the box. Commented Sep 29, 2020 at 15:03
  • 1
    @alephzero, Course for horses. Brick houses around here (California) have a bad habit of falling down if the ground shakes a little bit.
    – The Photon
    Commented Sep 29, 2020 at 21:28

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service and acknowledge you have read our privacy policy.

Not the answer you're looking for? Browse other questions tagged or ask your own question.