10

Am attempting to open an old device cover (an adapter) and it has these screws (please see attached image, sorry for the bad quality, I couldn't get better focus than this.)

Would really appreciate if someone could guide me identify it and/or point to where to obtain a driver for it. (Or even more awesome if any tips of opening it using any hack without a specialty driver, if possible!)

picture of bolt

Update Addendum

Well I am happy to report that — thanks to the help and solution below — I have acquired & successfully opened the Tamper-proof/Security Torx screw using the bit! (see more bad images below, :D Though I notice that a kind contributor has edited my original picture and fixed some text too, thanks!) :)

enter image description here enter image description here

  • 3
    While it's not perfect, the picture is perfectly good, really - shows what we need to see, even if the focus is slightly off. – Ecnerwal Aug 3 at 16:05
  • 1
    Am glad it was good enough for the solution. Thanks! :) – spcsLrg Aug 3 at 16:20
  • 2
    One trick for taking a closeup shot, is to not. Instead, back off a half-metre or so, take the photo, and then use a crop tool to cut out the extra. But this one is perfectly adequate. – Criggie Aug 4 at 6:41
  • 1
    I resized the blurry picture to 30% of the original size with GIMP. Still has not lost any information. Now you can resize your pictures next time. – Jonas Stein Aug 24 at 10:53
16

This is a tamper proof torx screw. There are torx bits with a hole in the center that will remove them, if you are bold you can try smacking the center pin with a punch at an angle (small ones usually snap off) and then a standard torx bit can be used to remove it. Check online and I bet you can find a tamper proof bit kit for under 15$.

  • 11
    Also Known As "Security Torx" – Ecnerwal Aug 3 at 16:03
  • 1
    Hm, if you really mash it though you might damage the screw and make it harder to remove. – whiskeychief Aug 3 at 16:45
  • 8
    I have seen people’s efforts to smack the center pin to cause the screw to bend or the casing break.... better to get the proper bits... – Solar Mike Aug 3 at 22:43
  • 1
    @spcsLrg Given that you can pick up a new security torx driver for < $1, shipped, (eBay), it's commonly easier to just get the appropriate bit. If you don't know the size, sets are a bit more expensive, but not much. While such sources may not give you the best quality, it should, at least, get a single job done. – Makyen Aug 4 at 1:29
  • 1
    I'd also recommend buying a good kit with a diverse set of bits. Years ago I thought I'd save myself a bit of money by only ever buying specific bits (or the smallest possible kit that had what I needed, typically 3-6 of a single type); but after doing that a few times you end up having spent the cost of a decent kit but still end up having to buy new bits because you've got a much less diverse collection than the kit you didn't buy in the first place. – Dan Neely Aug 4 at 15:57
3

Your picture shows a Security Torx screw head. https://upload.wikimedia.org/wikipedia/commons/thumb/9/9b/Screw_Head_-_Torx_Tamperproof.svg/40px-Screw_Head_-_Torx_Tamperproof.svg.png

You can find a good overview on most common screw drives for identification on a specific wikipedia page.

  • I never knew there was a wikipedia page with this info.Thanks! – Ed on PCR Aug 6 at 20:09

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service, privacy policy and cookie policy

Not the answer you're looking for? Browse other questions tagged or ask your own question.