3

I am in the process of building a roughly 12' x 16' shed/workshop. It is going to be a pier-and-beam design. There are 8 concrete piers, 4 on each side, that will support 2 4x12 beams. The span from the outside of one of the beams to the outside of the other is roughly 12'.

One possibility for joist/subfloor design:

  • 2x10 doug fir joists, 16" oc
  • One blocking sequence down roughly the middle
  • 3/4 inch plywood
  • Some form of construction adhesive between joists and plywood
  • Screwing and/or nailing plywood to joists.

I think it's a fairly sound design overall, but I'm not sure how much "give" there will be in the floor after completion. Do you think that would have a lot of bounce, or should that be plenty?

According to the IRC, both southern pine and doug-fir-larch should be able to span 12 ft for 40psf live load and 20 psf dead load at 16" oc. See: https://codes.iccsafe.org/content/IRC2015/chapter-5-floors?site_type=public .

Will this be sufficient to have a floor without significant bounce?

  • 2
    This all sounds good, and is slightly better than the design that I recently used and I didn't have bounce. You want to keep the 16" oc, and you don't want any less than 3/4" plywood. I thought I might get away with 1/2" ply, but that was terrible. I used all PT wood for the floor and foundation. That said, I don't feel like I have enough framing expertise to make this an "answer". – JPhi1618 Jul 17 at 19:53
  • Thanks. For your building, what was the joist span? – bddicken Jul 17 at 20:30
2

I recently build a 8x14 shed using 2x8 pressure treated joists and there was no bounce. It felt solid with a 3/4" PT plywood floor. Your design is larger, so I agree with the 2x10 that you spec'ed. I don't think you'll have an issue it all.

I was originally going to try and save some money so I mocked up a few combinations of 16" oc and 24" oc with 3/4" and 1/2" plywood since it was "just a shed". The joists 16" oc with 3/4" ply was the only combo that felt solid (as expected). The shed had a small 4' "porch". For that I did use 24" oc joists with 5/4" PT deck boards. That was a stretch that I wouldn't have made for a full on deck, but it was fine for the small porch that would only have a few people on it with no static load.

I had 6 piers, so your 8 sound good. The only thing I second guessed is the depth of my piers. I was digging alone, and manually so I didn't get them as deep as they should have been. I didn't notice a problem, but I would suggest getting the recommend depth in your area for sure.

  • Sounds good. In my case I wanted to use tongue & groove flooring, so I used PT joists with building wrap over them to keep moisture to a minimum. – isherwood Jul 17 at 21:09
  • Thanks @JPhi1618 – bddicken Jul 25 at 5:00
1

A follow-up, in case anyone visits this later and is curious about the answer.

Since posting, I have gone ahead and build the floor. The span was a little under 12' (about 11' 6.5"), and I used 2x10 joists with joist hangers. I used 23/32 plywood for the subfloor, and used liquid nails plus 2" deck screws to attach the plywood to the joists. It is solid enough for my purposes! If someone has a follow-up question, feel free to ask.

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service, privacy policy and cookie policy

Not the answer you're looking for? Browse other questions tagged or ask your own question.