I have patched a couple of places at the base of my shower with silicone rubber sealant, using a caulking gun and it has worked well. The water no longer escapes from the shower. However, where I have done the patching, it is lumpy. Where the original sealant is there is a smooth continuous finish.

Two questions:
1. Can the existing lumpiness (now dry) be made to look smooth?
2. What should I have done to make the finish look smooth and professional?

  • 1
    See also: diy.stackexchange.com/questions/35/…
    – BMitch
    Commented Jun 11, 2012 at 17:12
  • 1
    Make sure you don't seal all the way around your electric shower. You shouldn't seal underneath. The pressure release valve might go so you need somewhere for the water to go. This probably only applies to certain showers. It was a common problem on the ones I used to fit. Redring selectronic
    – Kev
    Commented Feb 27, 2017 at 18:28

18 Answers 18

  1. You will have to remove it and reapply.

  2. The trick is soap. Have a bowl of water and a bar of soap. Dip your finger in the water then rub it on the soap before using it to smoothe the silicone.

  • 2
    +1 for the soap idea. I've long used the "wet finger" technique, but don't like the mess left on the finger, and am hoping the soap will make that easier to deal with. I'm also thinking perhaps a wet bar of soap itself -- with rounded corner -- might substitute for the finger? Commented Jun 13, 2012 at 18:32
  • 2
    Silicon and latex caulks are different. With latex often just a wet finger is enough.
    – Bryce
    Commented Sep 5, 2012 at 7:53
  • 5
    Couple the soapy water with disposable latex-free gloves, and you get a smooth bead with easy clean-up. Commented Sep 19, 2012 at 1:49
  • Whoa...soap! Never thought of adding that to the mix to avoid the stuff sticking to the fingers.
    – DA01
    Commented Dec 3, 2013 at 1:04
  • Make sure to read the instructions on the product you're using: I recently saw some silicone caulk that explicitly said do not use soap. Commented Feb 5, 2023 at 21:45

Definitely use a damp finger, and have a paper towel ready to wipe off your finger if you used too much caulk. Also, with silicone and difficult to clean surfaces, you want to tape both sides of your caulk line first. Remove the tape immediately after using your finger. This isn't needed on trim/painted walls since the caulk will disappear under the paint. But for places where you need a nice edge on the caulk line this makes a big difference.

  • 4
    Not all silicone caulks are paintable. Commented Jun 12, 2012 at 8:52
  • @VebjornLjosa That's an important point that I probably wasn't very clear on. Thanks.
    – BMitch
    Commented Jun 12, 2012 at 10:13
  • 4
    I recommend against painter's tape. When you remove it after smoothing, you leave these nice mini-ledges at the edge of your bead that just beg you to pick at them, till all your dry caulk comes peeling off. Commented Sep 19, 2012 at 1:49
  • @JeremyW.Sherman The problem with not using the tape is that on some surfaces or some caulks (like unpaintable silicone), once it goes to the wrong place, it's not easy to fix. Worse than a ridge is a bunch of pealing paint or a crooked white streak of caulk in a porous tile.
    – BMitch
    Commented Sep 19, 2012 at 11:29
  • 12
    I've had success with taping. After I removed the tape, I made one more pass with my finger to lay the ridges down. The line stays fairly crisp because the excess was removed with the first pass.
    – Josh Bush
    Commented May 13, 2013 at 2:54

There's nothing you can do now other than remove it and re-apply. The pro's often just use their finger to smooth it out.

For those of us who don't have the magical touch, they make tools that allow you to put a nice finish on. There are a variety of different tools - this is just the first one that came up in a search.

Caulk Packer Tool


Do not use tape, cut the tube of silicone at a 45 degree angle and apply it as if that is the final application. Now use a ~$5 tool like this*:

Caulk tool

to spread the silicone. Its triangle has three different radii from eighth to quarter inch. It is made of silicone so it works better than any of the above suggestions. I do this for a living in all the bathrooms in a 400-room 4-star hotel. Use isopropyl alcohol to wipe any super thin layer left behind beside the caulked seam itself. Use neoprene or latex gloves and a rag to wipe off excess caulk that collects on the tool.

*Example only, not a recommendation


The cheapest tool you can get for the job is a Popsicle stick, which has a perfect end for a smooth finish. First of all, apply your silicone bead, then get a spray bottle with water and washing up liquid solution. Spray your bead sparingly and also spray your Popsicle stick then run it along the bead wiping any excess on a cloth as you go. At the end you'll have a perfect finish.

  • 1
    Thanks......but what is "washing up liquid solution"? Soap and water? Kerosene? Rubbing alcohol? Newbies need to know! :-) Commented Sep 19, 2017 at 14:03
  • @MichaelScott The stuff you squirt in your sink to clean plates and glasses that you don't wash in the dish-washer. Commented Jun 26, 2019 at 16:15
  • "Dish soap" is what we call it in the USA. Commented Feb 5, 2023 at 21:46

The best way is to use glass cleaner spray on your hands. It stops the silicone sicking to your hands so you can get a smooth finish. It also gives the silicone a nice shine when dried.


Just want to add:I used to use saliva on my finger,like a lot of people,but recently found out that the bacteria in your saliva starts the mold and discolouration,making the nice white bead around showers and sinks going black and moldy in no time(soaps water and two or three passes will get a neat clean job.)

  1. Remove existing silicon, with a suitable scraper tool, knife or spatula. Clean the area with methylated spirits, bleach or your preferred cleaner. The idea is to kill any mould or similar under the silicon before applying.
  2. Use a suitable silicon product, e.g with mould inhibitors for bathroom/kitchens. Cut the sealant tube tip so the bead is wide enough to apply enough silicon for the area. It's better to have a bit too much than too little.
  3. Lay the silicon bead along the line with a caulking gun.
  4. Spray onto the silicon line with soapy water from a spritzer bottle. This stops the silicon sticking and makes it more pliable when finishing it. It also kills any bacteria on the surface, preventing it getting into the silicon.
  5. Use these amazing "Sealant edges" for a perfect finish. Reusable sealant edges

  6. There's different corner sizes from 0mm, 2mm, 3mm, 4mm, 5mm, 6mm, 8mm, 10mm, 14mm to 20mm to match the job. Scrape off the excess sealant, discard with tissues or disposable cloth.

  7. Leave to cure 24 hours minimum for a perfect finish!

For water soluble caulks I apply the caulk, spread it with a wet finger, then trowel the caulk with my thumb nail. Finally, I wipe the joint with a damp tilesetter's sponge. It has rounded corners which create a nice looking smooth bead. A very forgiving system and easy to touch up. Keep rinsing out the sponge to get caulk out of it and to avoid smearing caulk on the next joint.

  • Welcome to Home Improvement! Thanks for the answer; keep 'em coming! Commented Apr 28, 2019 at 12:12

There are 3 good methods for smoothing silicone. 1) is a dry finger (this takes a lot of practice) 2) is plain water. Never put soap in the water. The reason is that as you pull your finger across the silicone a "wave" of soapy water will move ahead of your finger and get under the edges of the silicone bead. When the water under there evaporates the soapy residue is all that is left. This can cause feathering or fraying of the edges of the bead. 3) is a professional product such as Caulk EZ.

  • Hello, and welcome to Home Improvement. Thanks for the answer; keep 'em coming. And, you should probably take our tour so you'll know how best to contribute here. Commented Jun 26, 2019 at 16:16

Use an empty tube from your silicone, give it a spray inside so it doesn't stick to the inner tube so it doesn't pile up, squeeze the end of the tube to the desired width of the seal and run it along it, best tip I can give amateurs, popsicle sticks leave too much of a mess.


I agree with Josh. Going around the bath and inside the shower cubicle I tape up and as soon as I lay the sealant I get a tea spoon and scrape-off. When that is done I use wet soapy finger and quickly run round, this also gets rid of each bump as the spoon passes the grout line. As soon as I have done that the tape comes off immediately. Soapy finger again and one last run around just to take the little edge off. Had only praise from customers so far on a neat job. The tea spoons have different radius arcs on the tip so find the one with the most suitable arc for the gap from tape edge to opposing tape edge. I did see on the Tinterweb a tube video about using WD40 to lightly spray on the bead of sealant which looked a bit messy but I may try that at some stage (On my own tiles of course).


I do this for a living and it makes me laugh to hear what some people say is the best method. Use your finger...yeah right! Unless you use a special paintable silicone, paint wont cover it. Not all caulking compounds are the same. Now the simple method is apply silicone bead, spray with diluted detergent and then finish off on horizontal and vertical edges with a popstick. Flick the scraped off bits into a pot of dilute detergent solution. Change the popstick when edges become worn to keep a good finish. Run detergent moistened finger over the bead lightly after scraping off with popstick to prove the seal.

  • Oh yes the painters edge tools are good for wider gaps and I use those as well but they can damage bead if you dont use enough detergent as they scrape off the detergent so if you have another run the tool will start to scrape out the silicone. Spray again. Commented Sep 11, 2015 at 12:04
  • 3
    Have to point out that you ridicule using your finger and yet the last sentence states.... yup, use your finger.
    – handyman
    Commented Feb 27, 2018 at 19:46
  • Good call! Perhaps HIS finger is speeeeecial! Commented Nov 19, 2019 at 18:39

About silicone sealant proper, nearly everything has been said already. But when people say "silicone" in everyday, at least over here, they can mean different sealants / caulks, including silicone, acrylic polymer and polyurethane.

Techniques for polyurethane caulks

For polyurethane based sealants and construction glues (examples: Sikaflex-221, -252), using soapy water on the bead or finishing tool does not work at all. Some sealant will just stick to the tool and leave an uneven surface behind. Also, it's not a good idea to use the finger as these sealants are skin irritating / damaging.

Instead, I just found out that ethanol works well when sprayed on the bead and also put on a rubber-gloved finger to wipe along the bead. Ethanol is a good solvent for polyurethane sealants and will result in a layer of thinner sealant on the surface on which a gloved finger glides well. (It's not perfect yet, though; I might try adding dishwashing detergent to the ethanol next time.)

Side effect: As ethanol is a suitable solvent, cleaning tools, fingers, gloves etc. with ethanol from residue of polyurethane sealant also works well.

Techniques for other non-silicone polymer caulks

A friend's favourite technique is to let the sealant bead sit for a tiny bit of time so that the surface is not just starting to settle, and then to wipe along the bead with the finger covered with a wet-wipe made for use on infants. Not sure what type of sealant this works for exactly; just that it also works for silicone.


Rubbing alcohol in a spray bottle. Spritz entire joint after running a bead down.soapy water on the flanges and seat the bead perfectly in one continuous motion. Takes practice.


A surface slice of potatoe. Use the rounded corner. It's wet already, so the caulk does stick to it, it leaves a smooth surface and it's cheap.


Soapy fingers work well. A slice of potato also does a great job and does not spread the silicone as much as a finger.


Goof off works excellent when you put it on your finger and wipe the silcone bead clean.

  • 1
    Not such a great idea: the MSDS for Goof Off Caulk Remover says that it's a "Skin irritant. Symptoms may include redness, itching, drying of skin."
    – Niall C.
    Commented Oct 12, 2014 at 23:37

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service and acknowledge you have read our privacy policy.

Not the answer you're looking for? Browse other questions tagged or ask your own question.