I need to use a component video cable whose connectors have been cut off as a coax cable. Is that possible?

Here's the story: My TV is at location A). The OTA signal arrives by coax to location B) in the same room about 20 feet away. There's no coax cable that runs from location A) to location B) inside the wall and I'm not OK with running it outside the wall.

However, there are a few cables that run from location A) to location B) inside the wall. And old HDMI cable, 2 cat5 cables, and a component video cable with a red, green and blue wires. Thinking that I would never have use for it, I cut off the connectors so I could tuck the cable away into the wall.

Question: is it possible to adapt this cable the bring the OTA signal to the TV over the remaining 20 feet?

enter image description here

  • 1
    maybe for a few inches, but nothing more, and even then, not well; it's a total mismatch. you can use hdmi or cat5 though, with a modulator or some sort. i would drop the $20 for a used/fake chromecast though...
    – dandavis
    Commented Mar 15, 2018 at 3:50
  • How do you OTA->Chromecast?
    – Wynne
    Commented Mar 15, 2018 at 4:08
  • could use one of those cheap "adapter boxes" they basically gave away during the dtv roll-out. might also need an hdmi adapter. or a tivo-like thing (tuner+hdmi out). or an unused tv w/ video out...
    – dandavis
    Commented Mar 15, 2018 at 4:16
  • 1
    You could go to a thrift store and get 20 feet of coaxial cable for a couple of bucks and a coaxial cable coupler for a couple dollars.
    – Alaska Man
    Commented Mar 15, 2018 at 5:44
  • if you want to persue this why don't you trim it back so we can see what the core/shield looks like.
    – agentp
    Commented Mar 15, 2018 at 13:30

2 Answers 2


OTA DTV antenna cable is commonly RG6 (replaced RG59). This is a 75 ohm coaxial cable with an F or BNC termination (probably F). The better quality component video cables use 3 separate RG6 cables with RCA connectors at the end. They are simply attached together in a bundle. My original answer assumed this is what you had.

With the picture you've added it appears you have the more compact 3-way coaxial cable. Each conductor of this cable is 75 ohm and suitable for (composite) video over short runs. Whether it will support the higher bandwidth of OTA Digital is not certain. There's only one way to find out . . .

Solder on a BNC connector F-type coax connectors are crimp or twist on since they don't supply their own inner pin. BNC is fairly common for antenna connectors and has the right bandwidth for the signals you are trying to pass. Only expose as much of the conductor as you need to do a good solder job.

Given that your cable does not have the more common dimensions of an RG6 or RG59 cable it may be difficult to make a mechanically stable connection to a male cable connector.

I inferred from your question that the antenna cable is already in the living space (not in the wall, per se). Your best option to terminate this cable is a wall plate.

Connect the antenna and component cable directly. If both cables are already in the same wall cavity you can connect them directly (otherwise use a jack as below). Cut off the existing connector on the antenna cable, strip it back a little bit, and connect the inner conductor to one of the component cable conductors and the outer ground sheath to the component cable ground sheath. I would use a small heat shrink tube to insulate the inner conductor and a larger heat shrink tube to cover the ground sheath and give the joint some mechanical strength.

Install single-BNC wall plate jack(s) You can find these for BNC fairly easily (link). This allows you to make a clean and mechanically stable connection at each termination of the component cable. Or one side only if you directly connected to the antenna cable.

Plug the antenna cable into the wall jack at location B Assuming your antenna cable has an F-type connector use a BNC Male to F Female adapter. These are fairly rigid so probably no need to cut off the connector and replace with a BNC Male connector. You might even find one at a right angle so you cable hugs the wall.

Use a patch cable to connect your TV at location A Use an RG6 patch cable and another BNC Male to F Female adapter.

I should emphasize that I really don't know if a single conductor of your component cable can pass an OTA Digital TV signal. In fact I'm somewhat skeptical. Most OTA Digital stations are UHF so 400 - 800 MHz. NTSC video (single 480i signal) runs at 4.2 MHz. HDTV (single 1080p signal) runs at 25 MHz. We moved from composite video (one conductor) to component video (three conductors) to handle a single 1080p signal. And the connection I proposed above may only support the bandwidth of a composite video cable. Caveat emptor

  • You are right: component video cables - I'll edit my post. I'll give your suggestion a try!
    – Wynne
    Commented Mar 15, 2018 at 4:26
  • Also, I've added a picture of what I'm dealing with. I'm not sure how to crimp on a coax connect to what I've got.
    – Wynne
    Commented Mar 15, 2018 at 4:40
  • 3
    Is the video cable fixed inside your wall? Can you use it to fish a new RG6 cable thru the wall?
    – Stanwood
    Commented Mar 15, 2018 at 11:33
  • 1
    @mrog the antenna (RG6 or RG59) and component video cables are both 75 ohm. There's no impedance mismatch. Doesn't mean the connections will be without reflections though.
    – Stanwood
    Commented Mar 15, 2018 at 16:29
  • 1
    I updated my answer to allow for direct connection of the antenna cable. And yes, you are connecting to only one conductor. Connecting to all three would give you an impedance mismatch.
    – Stanwood
    Commented Mar 15, 2018 at 18:47

Coax Cable has a particular shielding and is designed for the frequencies that will be carried on it. Your Composite wire does not have that design so your signal will be degraded and quite possibly to the point where you can not get a decent signal.

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service and acknowledge you have read our privacy policy.

Not the answer you're looking for? Browse other questions tagged or ask your own question.