I have this desk, and I love it so far. It's a big desk and pretty sturdy for being extremely cheap and made of particle board.

My problem with it is it being 4" shorter than my last desk, which I thought I could get used to but that is proving impossible. I get strain in my lower back and shoulders when I am at my desk for more than 2 hours, which previously I could work for 8 hours straight and not even notice.

I want to raise my desk by 4 inches, hopefully in a more elegant way than shoving some books under it or wood gluing some 2x4s.



  • I am not at the desk itself right now, since I am at work. they are at least 3/4" though, might be as much as 1" – Nathan Perkins Aug 25 '17 at 16:51
  • eight bricks, assuming 4 legs on the desk – Ecnerwal Aug 25 '17 at 18:27

I probably would rip a 2x6 down to 4 inches, make a three sided frame out of that and put the desk on top of it. Then attach the desk to the frame with some pieces of metal called "mending plates". make the inside dimensions of the frame the inside dimensions of the desk. Paint the new wood and plates black. If you wouldn't like the look of 2x4s at the bottom, you could cut some strips out of 3/4 plywood (or whatever thickness the desk is) and attach those to the desk bottom in some way, like more mending plates or pieces of wood.

You could Isherwood's idea, only use 2x4s instead of aluminum tube. Probably be a cheaper.

There are also "bed risers". They re small cone line platforms. It would take 4. I personally wouldn't like this because it wouldn't be that stable.


To maintain the clean, elegant look of the desk, I'd do this:

  1. Get yourself some 3/4" by 1-1/2" aluminum box tubing. You may find this at your hardware store, but a metal wholesaler might be a better option. You'll need four lengths, each the inside height of the desk sides plus 4".

enter image description here

  1. Buy some hammered-finish spray paint (or something else that coordinates with your desk's pattern).
  2. Cut the aluminum "legs", if necessary, and pre-drill them for at least four 3/16" screws each, spaced uniformly starting at about 6" from one end.
  3. Paint the legs.
  4. Mount the legs to the inside of the desk sides, tight to the top, using #14 or 3/16" screws. Pilot as needed to prevent blowout or bulging of the outer face of the desk. Masking tape on the bit helps gauge depth. I'd set the legs back from the front edge an inch or so, rather than leaving them flush, to reduce their visual impact.
  5. Add some black table feet to the tubing bottoms to save your floor.

enter image description here

Alternatively, buy some threaded insert feet to give yourself some height adjustability.


Add 4" locking wheels to the legs of the desk.

I'm new here. I just saw the actual desk. Doh!

You can't do much to the bottom because particle board doesn't act like solid wood, because it isn't.

Find someone who is tired of their drafting table and really wants a particle board desk.

Some adjustments aren't worthy of our precious ability to remedy them. I found this out the hard way, of course.

  • 2
    Please be more specific. How would you mount them to 3/4" or 1" particle board in a way that wouldn't tear out at the first bump during a desk move? – isherwood Aug 25 '17 at 18:53

You could make or buy a set of risers. These are commonly sold for desks and beds, and are available in a variety of styles/materials.

Here's one set wooden riser blocks

Alternatively, if the feet on your desk are a standard screw, you could just buy a set of legs (like for a couch) and replace the bottom pads.

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service, privacy policy and cookie policy

Not the answer you're looking for? Browse other questions tagged or ask your own question.