3 edited body
source | link

If you want to add a new layer of brick wall then it is best to remove the drywall completely and get right back to the structural, original wall.

As commented, using full bricks will cause allota lot of weight on your load bearing structure and could cause serious damage to your structure!

Rip the drywall out and get to your bricks. As long as you are only going to partially build the wall up you can use brick toothing but will require you to remove existing selected bricks from the existing wall and place insert your new bricks into the exists wall at a right angle in several places. Do not removed an entire course at once and do it in steps. several a day over a week - you need the new brocksbricks to rebond properly so they can exert the weight.

Toothing is mostly used for decoration but I have seen it used for adding extra support and bonding to an existing wall too- But doing a full wall needs extra steps.

enter image description here

But you will be placing the bricks at a 90 degree angle making a platform for your new decorative wall.

enter image description here

These can also be used instead of tie ins at various places and heights of the wall. You can choose a pattern of your liking. It is best to put more at the bottom for bearing the load and a constant interval throughout the rest. I have no formula but more it better and too much is worse.

enter image description here

  • This type of DIY I would categorize as ADVANCED It is time consuming, can turn out to be expensive but is the best solution for long term (+20years!)

If you want to add a new layer of brick wall then it is best to remove the drywall completely and get right back to the structural, original wall.

As commented, using full bricks will cause allot of weight on your load bearing structure and could cause serious damage to your structure!

Rip the drywall out and get to your bricks. As long as you are only going to partially build the wall up you can use brick toothing but will require you to remove existing selected bricks from the existing wall and place insert your new bricks into the exists wall at a right angle in several places. Do not removed an entire course at once and do it in steps. several a day over a week - you need the new brocks to rebond properly so they can exert the weight.

Toothing is mostly used for decoration but I have seen it used for adding extra support and bonding to an existing wall too- But doing a full wall needs extra steps.

enter image description here

But you will be placing the bricks at a 90 degree angle making a platform for your new decorative wall.

enter image description here

These can also be used instead of tie ins at various places and heights of the wall. You can choose a pattern of your liking. It is best to put more at the bottom for bearing the load and a constant interval throughout the rest. I have no formula but more it better and too much is worse.

enter image description here

  • This type of DIY I would categorize as ADVANCED It is time consuming, can turn out to be expensive but is the best solution for long term (+20years!)

If you want to add a new layer of brick wall then it is best to remove the drywall completely and get right back to the structural, original wall.

As commented, using full bricks will cause a lot of weight on your load bearing structure and could cause serious damage to your structure!

Rip the drywall out and get to your bricks. As long as you are only going to partially build the wall up you can use brick toothing but will require you to remove existing selected bricks from the existing wall and place insert your new bricks into the exists wall at a right angle in several places. Do not removed an entire course at once and do it in steps. several a day over a week - you need the new bricks to rebond properly so they can exert the weight.

Toothing is mostly used for decoration but I have seen it used for adding extra support and bonding to an existing wall too- But doing a full wall needs extra steps.

enter image description here

But you will be placing the bricks at a 90 degree angle making a platform for your new decorative wall.

enter image description here

These can also be used instead of tie ins at various places and heights of the wall. You can choose a pattern of your liking. It is best to put more at the bottom for bearing the load and a constant interval throughout the rest. I have no formula but more it better and too much is worse.

enter image description here

  • This type of DIY I would categorize as ADVANCED It is time consuming, can turn out to be expensive but is the best solution for long term (+20years!)
2 added 163 characters in body
source | link

If you want to add a new layer of brick wall then it is best to remove the drywall completely and get right back to the structural, original wall.

As commented, using full bricks will cause allot of weight on your load bearing structure and could cause serious damage to your structure!

Rip the drywall out and get to your bricks. As long as you are only going to partially build the wall up you can use brick toothing but will require you to remove existing selected bricks from the existing wall and place insert your new bricks into the exists wall at a right angle in several places. Do not removed an entire course at once and do it in steps. several a day over a week - you need the new brocks to rebond properly so they can exert the weight.

Toothing is mostly used for decoration but I have seen it used for adding extra support and bonding to an existing wall too- But doing a full wall needs extra steps.

enter image description here

But you will be placing the bricks at a 90 degree angle making a platform for your new decorative wall.

enter image description here

These can also be used instead of tie ins at various places and heights of the wall. You can choose a pattern of your liking. It is best to put more at the bottom for bearing the load and a constant interval throughout the rest. I have no formula but more it better and too much is worse.

enter image description here

  • This type of DIY I would categorize as ADVANCED It is time consuming, can turn out to be expensive but is the best solution for long term (+20years!)

If you want to add a new layer of brick wall then it is best to remove the drywall completely and get right back to the structural, original wall.

As commented, using full bricks will cause allot of weight on your load bearing structure and could cause serious damage to your structure!

Rip the drywall out and get to your bricks. As long as you are only going to partially build the wall up you can use brick toothing but will require you to remove existing selected bricks from the existing wall and place insert your new bricks into the exists wall at a right angle in several places. Do not removed an entire course at once and do it in steps. several a day over a week - you need the new brocks to rebond properly so they can exert the weight.

Toothing is mostly used for decoration but I have seen it used for adding extra support and bonding to an existing wall too- But doing a full wall needs extra steps.

enter image description here

But you will be placing the bricks at a 90 degree angle making a platform for your new decorative wall.

enter image description here

These can also be used instead of tie ins at various places and heights of the wall. You can choose a pattern of your liking. It is best to put more at the bottom for bearing the load and a constant interval throughout the rest. I have no formula but more it better and too much is worse.

enter image description here

If you want to add a new layer of brick wall then it is best to remove the drywall completely and get right back to the structural, original wall.

As commented, using full bricks will cause allot of weight on your load bearing structure and could cause serious damage to your structure!

Rip the drywall out and get to your bricks. As long as you are only going to partially build the wall up you can use brick toothing but will require you to remove existing selected bricks from the existing wall and place insert your new bricks into the exists wall at a right angle in several places. Do not removed an entire course at once and do it in steps. several a day over a week - you need the new brocks to rebond properly so they can exert the weight.

Toothing is mostly used for decoration but I have seen it used for adding extra support and bonding to an existing wall too- But doing a full wall needs extra steps.

enter image description here

But you will be placing the bricks at a 90 degree angle making a platform for your new decorative wall.

enter image description here

These can also be used instead of tie ins at various places and heights of the wall. You can choose a pattern of your liking. It is best to put more at the bottom for bearing the load and a constant interval throughout the rest. I have no formula but more it better and too much is worse.

enter image description here

  • This type of DIY I would categorize as ADVANCED It is time consuming, can turn out to be expensive but is the best solution for long term (+20years!)
1
source | link

If you want to add a new layer of brick wall then it is best to remove the drywall completely and get right back to the structural, original wall.

As commented, using full bricks will cause allot of weight on your load bearing structure and could cause serious damage to your structure!

Rip the drywall out and get to your bricks. As long as you are only going to partially build the wall up you can use brick toothing but will require you to remove existing selected bricks from the existing wall and place insert your new bricks into the exists wall at a right angle in several places. Do not removed an entire course at once and do it in steps. several a day over a week - you need the new brocks to rebond properly so they can exert the weight.

Toothing is mostly used for decoration but I have seen it used for adding extra support and bonding to an existing wall too- But doing a full wall needs extra steps.

enter image description here

But you will be placing the bricks at a 90 degree angle making a platform for your new decorative wall.

enter image description here

These can also be used instead of tie ins at various places and heights of the wall. You can choose a pattern of your liking. It is best to put more at the bottom for bearing the load and a constant interval throughout the rest. I have no formula but more it better and too much is worse.

enter image description here