Tag Info

Hot answers tagged

12

Spiders are predators, they go where the food is. If spiders are attracted to your shed, it means prey insects are attracted to your shed. Get rid of the prey. Remove nearby vegetation and organic matter that provides food/shelter for bugs Remove any standing water (bird baths, puddles, soil that soaks up moisture) Remove light sources (bugs fly towards ...


10

Take a look at your local Lowe's, Home Depot or even Amazon online book store. They have several books with lots of different designs. You can look them over and just buy the book that suits your needs. They will have diagrams and material lists. Also these books are fairly cheap. Good luck.


9

The problem here of course is that snow/freezing rain gets into the lock and freezes. With a house, this isn't normally a problem for a few reasons. First, you use it often enough that it doesn't get that bad, and second the inside of the house is warm, which prevents water from freezing inside the lock (unless it gets really, really cold I suppose). You ...


9

I did a quick search for information about chestnuts and spiders and found conflicting advice. My take is that even it doesn't work, it can't hurt; the worst that can happen is that you still have spiders and some (apparently useless) chestnuts on the floor of your shed. Caulking small gaps in the shed walls is a good idea in general, but the biggest gap ...


9

This should be a good starter project, here are a few tips I've picked up over the years: Even pressure treated wood will deteriorate over time if it's exposed or in direct contact with the ground/moisture. Do what you can to protect it from the elements and get it raised off of the soil. Use a moisture barrier between wood and concrete. Take care to ...


7

This website has quite a few links for free plans. They're a mix of slab plans and elevated floor plans. You'll have to click through several levels down, but here are some direct links to some of the nicer ones: Basic 6'x8' shed plan with cinder block base. (Expandable up to 8'x12'). Larger 8'x12' shed plan with double doors. This site is also listed ...


7

I'd use a foundation. It doesn't have to be very deep - it could just be a set of paving stones covering an area slightly larger than the shed itself. If nothing else it will keep the wood away from the ground and reduce the damp and moisture that will attack the shed, thus prolonging it's life. It will also help keep the shed level.


6

The assembly instructions state: Recommended surfaces for installation include cement or treated wood deck style surfaces. So it should be installed on a level platform of some kind that will support the weight of the shed and its contents. It wouldn't be a good idea just to use level ground as you'll have problems with moisture, rodents etc (as Eric ...


6

Any place that sells pre-built sheds in your area would likely have advice on site preparation for delivery. I don't know what the soil's like in your area, but if you're going to hit bedrock before 42", it'd likely be easier to put in a slab; If you're likely to hit lots of tree-roots, the slab might be a better choice (so you don't kill a tree, and have ...


5

A block wall that is actually part of the original outside wall of the main structure is most certainly a load bearing wall or part of the foundation. It is possible to open a six foot section, but care must be taken to install a properly sized supported header or if block is still going to be above the opening, a steel lentil. You will need some temp ...


5

Wood in contact with the ground will always rot. Treated wood will do it slower. Depending on your climate, the shed might rot out in just a couple of years. So yes, you need a foundation, but as @ChrisF notes, it can be simple. Or if you live someplace like Tuscon and drainage is away from the shed, you might be able to get away without it, as the climate ...


5

Because the roof is metal it will get cold and when the (relatively) warm damp air inside the shed comes into contact with it, condensation forms. You need to make sure that there is a thermal barrier between the inside surface of the roof and the outside surface. So any of the things you suggest would do, but might cause ventilation problems (say). So a ...


5

For my on grade shed, I first built a bed of crushed limestone for it to rest on. This will allow drainage and breathing room below the shed. I used some landscape timbers and made a "retaining wall" for the limestone just slightly larger than the footprint of the shed (like 2' around each side). I then filled this rectangle landscape timber area with ...


5

The verbiage of the laws is very important. After some research, I think I've found what you're referring to. Outbuildings are considered to be permitted development, not needing planning permission, subject to the following limits and conditions: Outbuildings and garages to be single storey with maximum eaves height of 2.5 metres and maximum ...


4

As with any advice you get here, keep in mind that you must stay within the bounds of IRC building codes adopted by your local municipality. Obtain a building permit and a local inspector will give you guidelines on minimum requirements for posts, beam spans, joist spans, etc... Your concrete piers must be a set depth to go below the frost line in your ...


4

You'll need to check your local codes. In the US, most building code sections begin with a list of definitions, and I assume it's the same elsewhere. If the difference between a shed and a garage is legally significant then they probably define it. It could be based on size, intended use, access to utilities, proximity to other buildings, access to a ...


3

Gluing won't hurt, but it won't help either (in this application) so I wouldn't bother. Where gluing does help is when you are doubling a beam by stacking two smaller beams on top of each other. (i.e. 2 2x4's to make a 2x8) Gluing will then help transfer the longitudinal shear stresses that develop when the beam bends slightly. (To visualize this shear, ...


3

Easy: Motion detection lights. Difficult: Alarm system. High maintenance: Guard dog. Anything can be broken into by a determined thief, the idea is to make your place less attractive of a target than the next place.


3

You have electrical in your shed. Before doing anything that branch needs to be terminated correctly. I don't think there is a pure art to the small demo. I personally would slice the front wall beams halfway up with whatever saw I thought would be the quickest and then sledge hammer from the corners. Roof should fall/slide down. Then I would just ...


2

Just lay some tongue-and-groove OSB plywood on top of the planks. For a 6x8 shed, you should only need two 4x8 sheets - which should certainly cost a lot less than the £120 you would pay for sealer. Or for that matter, just have them use T&G plywood for the flooring in the first place.


2

Honestly, your best bet may be to re-build the structure using an exterior grade plywood. Whatever solution you come up with to "weatherize" the MDF will only be temporary. Soon enough, there will be some damage done to the protective coating that you apply, and then when the next storm comes by you will have a soggy pile of sawdust instead of a shed. Do ...


2

Lamp on the left so that your work hand doesn't block your light, which is more probable to be the case than the other way around. As far as the vice goes, I'd say it depends on how you orient it and if there is a wall on the left or right side. If there is no wall on either side, I'd put it on the front-left so that it is near the lamp, and because if the ...


2

You got a strange problem for an outdoor storage building. A dehumidifier is gonna cost you a mint to run if the moisture problem is that bad. Two things to think about. First, where is all this moisture coming from? can you mitigate the source? Second, look at the gables or sofits to see it you can install some good venting. You can put a ridge vent on ...


2

Measure the 2 diagonal distances to the corners. If the measurements are not the same, the floor is not square. Not sure what you are levelling to. A level, framing square, and careful measuring solves most layout problems. 16" spacing is fine as long as your sheathing is rated for 16" spans. Sounds like they are spanning about 6 feet? 16d common nails ...


2

Look at a flooring store for sheet vinyl also called linoleum, remnants (the end of rolls). They can be inexpensive and would be seamless. An alternative that would be more slip resistant is something we call locally porchpaint. It covers many New england porches. It is only available in gray and is an oil based enamal. You can spread sand on it while wet ...


2

For the R-Value of your walls and roof, it will depend on the depth of the framing, but assuming you're using 2x4 studs in your wall, then R18 is pretty standard. For your ceiling, again depending on your framing, R30 or R38 is typical for batts. Remember that you may be able to squeeze a higher R-Value batt in between the framing, but compressing the ...


2

Impossible to say. The shed was designed to be supported in a particular manner. It has to be supported that way. If you're not inclined to that, though, an intermediate structure can be built underneath the shed that will support the shed in that manner, and which itself is designed to be supported in some other way, such as an array of 9 footings. Kind ...


2

Drill a hole, or a recess, into the bottom plate of the prefab wall, so the bolts holding the sill plate to the concrete just slide right in/through. Or, drill a similar recess into the sill plate, recess the nut into the sill plate (probably with a washer to spread the load over the thinner wood), and grind/cut the bolt off level with the top of the ...


2

Safe loads are determined through engineering and experimentation. The experimentation is used to gather real-world data, which then is used as input to engineering processes, which then result in guidelines and building codes. This is all updated over time as new materials are introduced and new experience is gained. When there's a situation that is ...



Only top voted, non community-wiki answers of a minimum length are eligible