The tag has no usage guidance.

learn more… | top users | synonyms

2
votes
1answer
97 views

What is the purpose of the crown in the middle of a router mounting plate?

I purchased a router table mounting plate to go inside a custom made table. The insert includes some crown in the middle of the plate. The height of the crown is roughly 0.030". At fist I thought ...
2
votes
1answer
2k views

Are pocket screws strong enough for a bed frame?

I've built a loft bed for my 4 year old following the plans posted here: http://ana-white.com/2012/07/plans/camp-loft-bed-stair-junior-height I modified the plans slightly to use a ladder instead of ...
2
votes
3answers
1k views

Best way to create a simple and economic steam machine for steaming wood?

I want to build a simple steam machine for steaming wood to bend. To do this I must place the wood into a sealed PVC pipe and pump steam into it. The PVC pipe part is the easiest part. Producing ...
2
votes
2answers
823 views

How do I fix bare spots on my table after applying polyurethane?

I polyurethaned my table and when it dried, it had spots. That is the best way to explain it. It looks like the eraser-sized spots are bare wood, almost like something made the polyurethane push away ...
2
votes
1answer
66 views

How important is the scoop cut in a drop-in joint?

I've been reading up on joints, particularly drop-in joints. Some of the drawings have a curved cut on the underside leading up to the tenon, sometimes labeled a "scoop cut". Curves make ...
2
votes
1answer
1k views

Can a drywall screwdriver be used as a regular power screwdriver?

I will be buying (or renting) a drywall screwdriver, I want to save a bit and have a tool that can be used for woodworking later, can it be used? Is it too low torque (I guess it is about 7 Nm) for ...
2
votes
2answers
189 views

How do I clean reclaimed wood from construction?

I'm building a house (brick, cement and concrete) and I have a big pile of wood used for beam and pillar molds. How can I properly clean cement off wood? I think it should be very damaging to blades ...
2
votes
2answers
1k views

How can I build an insert on a desk that adjusts the height of a sewing machine?

I'd like to take my executive desk ( now sewing table) and cut out a piece of it to use as a support for my sewing machine. I want the sewing machine support able to lower the machine to table height, ...
2
votes
0answers
118 views

Repurposing Old Subfloor Planks [closed]

I am pulling up my old subfloor (my house was built in 1928) in the attic which consists of tongue and groove wooden planks. Any ideas for repurposing them as a wood working project?
1
vote
4answers
128 views

Woodworking workflow

I'm totally new to woodworking (cabinetry, to be specific), and need verification that I'm going about this in the correct order, from a high level. This is what I have in mind for a general workflow....
1
vote
3answers
1k views

How can I make tongue and groove cuts with only a radial arm saw?

I'm pretty new to woodworking and I don't have a lot of tools. I'm working to make pieces to sell and buy more tools as I go. I don't own a table saw, but I do have a radial arm saw. Has anyone ever ...
1
vote
3answers
1k views

Any way to do a mitered corner without a table saw?

I want to use some left over wood from a table i did to build a 1ft^3 storage box to use in the living room. The wood has a beautiful pattern but it is plywood so i do not want to expose the edges. ...
1
vote
5answers
6k views

Possible to flatten warped wood?

I have two sections of 3x12" wood that have been out in the weather for a few years and are now bowed across the 12" width of the wood. The dip is pretty severe, maybe 1/2 an inch? It seems like ...
1
vote
2answers
649 views

What is the best way to level a tree log?

I'm making an end table/floor lamp from a 3 ft cut log. What's going to be the easiest or best way to level the bottom and top of this piece? I thought about throwing it up on some saw horses and ...
1
vote
3answers
70 views

DIY lamp post using 4x4 pressure treated wood?

I would like to build several lamp posts for my backyard. To cut costs I am considering dadoing a channel down the middle of a 4x4 for the wiring, and covering up the dado with "ornamental" wood ...
1
vote
2answers
226 views

What material is used to fill cracks in wood that looks black afterward?

When looking in the more stylish furniture shops, they often have very large tables (e.g. 10cm thick x 1m wide x 2-3m long, made from one piece of lumber. Understandably, such pieces often have come ...
1
vote
1answer
441 views

How do you build a bookcase around an outside or convex corner?

How do you build a bookcase around an outside or convex corner?
1
vote
2answers
107 views

Split ladder legs for child's playset

Last year I assembled a playground kit for my son and noticed the one leg on the ladder is splitting where the step boards were pre notched to fit into. The wood is basically pre stained red cedar. I ...
1
vote
4answers
682 views

how to cut multiple 2x4 to a same length with a circular saw

I need to cut three 2x4 pieces (about 2 feet) and their size should be exactly identical. What would be a good way for doing that with a circular saw? The articles I found recommend using a miter saw ...
1
vote
1answer
423 views

How to cut a 1 inch thick 12x48 plank in half (thickness)?

I was wondering how you would go about doing this. I have a 48x12x1 Bamboo blank. I'd like to cut the thickness in half so I have 2 planks. Perfect 0.5 width (with blade) does not matter as long as it'...
1
vote
2answers
447 views

What is a good reference book for cabinetmaking and/or other millwork?

I'm interested in making some cabinets and shelving. I have basic carpentry experience but have never tackled a project like this before. I'm looking for a good, illustrated guide to making cabinets ...
1
vote
2answers
229 views

Baseboards on wavy wall

I have a 25 foot drywall wall left that I am doing some wainscoting... I ripped up the old baseboards, and am bumping them out 3/4" basically following this guide a bit: http://www.familyhandyman.com/...
1
vote
2answers
1k views

What types of tools are required for making wood toys and models?

I am learning and doing some woodwork, and I have been using a hand saw and sanding to make very simple wood blocks. I would like to know what tools are suitable for toys like this puzzle and these ...
1
vote
3answers
299 views

How do I join pieces of wood tiles, 12“ by 12” pieces, to make a larger slab?

I have a project to work on that requires me using larger pieces of planks than what I currently have. I have square planks all over the porch that would suffice if only I had a good way of fitting ...
1
vote
2answers
2k views

How to repair a small hardwood crack?

I have a maple bench that recently decide to crack. I'm not sure what's the cause. I'm guessing wood expansion due to humidity changes. Anyway, I've decided to look around for solutions on fixing the ...
1
vote
3answers
149 views

How to sand wood without flattening it

I'd like to sand some wood planks on a rustic table to remove paint stains, but keep the rough wood structure (1-2 mm height difference). How can I do that?
1
vote
3answers
127 views

How to make a straight groove easily?

I have a project for which I need to cut a groove in 44x44mm wooden plank. The groove is supposed to be 15mm deep and about 3-4mm wide, as well as no less than 150mm long. It is supposed to be ...
1
vote
1answer
76 views

How do I reinforce an old mortise and tenon joint?

I have some old This End Up chairs with mortise and tenon joints that came reinforced with nails. They are generally pretty sturdy but have gotten quite the wiggle over their 33 years. My question is ...
1
vote
4answers
117 views

Finish a laser engraved piece of wood

I've laser engraved text onto a wooden plaque . The engraving has some finely spaced grooves. I want to apply a stain on it , sand it out so that the engraved portion is darker than the rest. I'm ...
1
vote
2answers
3k views

How can I round the edges of a piece of wood?

I need a piece of wood to place above a window, to which I'm going to attach a curtain rail. I'd like it to match an existing piece of wood above another window, which has quarter-round edges all ...
1
vote
1answer
95 views

Can I use a universal 22" wood saw for cutting studwork?

I'm a newbie and do not have much experience with sawing, or working with wood. I need to buy and cut into various lengths some wood for studwork (at varying thickness levels). What kind of saw ...
1
vote
1answer
99 views

Is softwood appropriate for furniture squares on a hardwood cabinet?

I'm building some cabinets out of 3/4" plywood, and I'd like to use 2x2" (nominal) stock as furniture squares. These squares will be on the interior only; it's not visually necessary for the interior ...
1
vote
3answers
9k views

Is it safe to use barn wood indoors for furniture, trim, walls and ceilings?

I am renovating a farm house built in the late 1800's. I am planning on tearing down the barn from the same era and using some of the wood to finish trim etc. I believe the moisture content is good 7 ...
1
vote
3answers
11k views

How do I properly nail two 2x4's at a 90 degree angle?

Nail the horizontal 2x4 into the vertical 2x4 about 1/4 of the way down from the top of the vertical 2x4, so they are at a 90 degree angle. The way I've been nailing this scenario is to just nail ...
1
vote
2answers
54 views

stair intersection design ideas

I currently have some angled stairs going from my garage into the home. To the left of these stairs is a closet that I'm going to take out to allow more open space in the garage. Directly to the right ...
1
vote
3answers
106 views

Does a router smooth edges significantly more than a jigsaw?

My first experiment with a jigsaw produced a nicely rounded shelf, but it's terribly rough. I am considering reducing the labor needed to properly sand it by getting another toy: a router. A nice side ...
1
vote
2answers
53 views

Multi-cutter blade blunt in 1 day. Bad blade? Bad Technique?

I recently bought Dewalt's Oscillating Multitool. (DSC355) It came with (amongst others) a wood blade and a "wood with nails" blade Today I was using it to replace wooden brick in a parquet floor. It ...
1
vote
2answers
75 views

Staggered block matrix

Could anyone provide advice on what would be an effective way of building something similar to the staggered block matrices as shown in the two photos below: Regarding materials, solid wood would ...
1
vote
4answers
2k views

How to fix bar stools that are too short

I bought bar stool chairs but they are too short for the bar area. Is there a way to make the chair stools longer in length?
1
vote
1answer
2k views

DIY Diving Board

I am thinking of building a diving board for my pool, and I'm not sure how to calculate the thickness requirement for a 250lb person to use it (I chose this because that seems to be what a typical ...
1
vote
1answer
266 views

When is a table top too heavy for just four legs?

I'm making a coffee table out of an old bowling alley lane and it's 4'x18". I wish I knew exactly what it weighed but it is heavy. It's too heavy for me to move without dragging it - although I'm ...
1
vote
3answers
269 views

How can I repair a joint on the legs of my table?

I need to repair the legs on my dinging room table. The joint is coming loose. I've included pictures, instead of trying to explain the situation. The first picture is a picture of the leg. The next ...
1
vote
3answers
130 views

How much clearance should I allow for a coat of poly?

I'm working on a project that will have wooden inserts sliding into a groove. I've done something similar before and ended up with too small of a groove after a few coats of paint (even though I ...
1
vote
2answers
142 views

How to finish cedar deck chairs

I'm building Adirondack chairs out of cedar that I'll use on my front porch. I want to keep the natural cedar color, but also protect them from the elements and prevent them from getting gray and ...
1
vote
2answers
3k views

When installing a stone fireplace, do I install the wood mantle first?

I have an existing, irregular river-stone fireplace and would like to fit a solid pine slab mantle to the surface. I have considered scribing the top and bottom surfaces of the wood mantle, but I do ...
1
vote
3answers
4k views

How to build disassemblable structure?

I'd like to build a largish (6' x 7' x 4') structure that can be assembled and disassembled on-site with only hand tools. I'm thinking about things like insert nuts, cam lock nuts, mortise/tenon ...
1
vote
2answers
308 views

What types of businesses have tree roots available?

I'm looking for some tree roots to make some custom tap handles. I live in the middle of Portland, Oregon so I can't exactly go cut down a tree by myself. Do lumberyards sell them? Do tree-removal ...
1
vote
2answers
112 views

Should I have any readily apparent concerns about the foundation and framing of this new build?

Should I have any readily apparent concerns about the foundation and framing of this new build in the Seattle, WA area? Is there any reason to get an inspection prior to building completion? I don't ...
1
vote
2answers
563 views

How can I remove a stuck screw that will still turn?

I put a too short screw into the screw hole. I thought this would sort things out. It didn't. Now I cannot get the screw out even though it will turn quite freely with a Phillips screwdriver. Any ...
1
vote
3answers
1k views

What cut of wood should I use for door stile & rails?

I'm starting a project to build a pair of bi-fold doors for a closet (its an odd size, and so there are no prebuilt doors of the required size). I've done research on building the doors, and think I ...