The tag has no wiki summary.

learn more… | top users | synonyms

3
votes
3answers
701 views

How to select a good Triangle (Speed square?)

My father is now retired and has returned to his hobby of being a woodworker. He's been helping me build a standing desk for my office and happened to mention while we was working that he wished he ...
3
votes
1answer
232 views

How do I fix a warped kitchen cabinet?

The side wall of the cabinet is slightly warped after I used the high temperature self-clean feature on the oven. This cabinet has three large drawers in it and now they won't close. The wall of the ...
3
votes
3answers
681 views

Are plywood dovetails a good solution to building something that needs to be dismantled?

Are hand cut, plywood dove tails feasible? Assuming you can get "good" plywood, i.e. not the brittle splinter-fest I've seen around, is dovetailing feasible? I'd like to avoid using glue for the ...
3
votes
3answers
1k views

For pine shelves, do I need to stain before applying polyurethane?

I built some pine shelves. They're pretty, but I don't want them to darken. I'm told I can apply polyurethane to ensure they stay nice and bright. My question is this: do I need to apply some kind of ...
3
votes
1answer
1k views

Is the 60T blade that came with my Dewalt DWS780 miter good for general purpose cutting?

I recently bought a Dewalt DSW780 12" sliding compound miter saw, along with 60T and 96T diablo blades. My question is, should I keep the blades? Is the 60T blade that came with the saw good enough? ...
3
votes
3answers
668 views

Is it possible to reduce a 1“ thick board to 1”/N boards?

I have some project plans. Most of the project calls for using 1/2" parts. I bought 1" thick wood, which actually only ends up being 7/8" when I measure it (I have heard this is normal). Anyway, ...
3
votes
2answers
1k views

Are there any good videos available that teach basic carpentry?

I apologies if this was already covered but I could only find a thread on books, and it was geared towards someone having some basic skills already. While I am far from useless, I never had a reason ...
3
votes
2answers
953 views

How to cut curved legs for a table

I'm planning to build a bed-side table and wish to build it with gently curved legs. I'm planning to recycle wood some old hardwood doors by cutting the blocks out with a circular saw, then cutting ...
3
votes
2answers
245 views

How can I clamp two 325 mm planks while gluing them together?

I have a base that is 650mm deep. I'm going to have to glue several planks together to get this depth and, eventually, the last two to make the 650mm base. The problem is, I don't have (and can't ...
3
votes
3answers
291 views

Stain-grade wood repair for door mullion?

One of our dogs apparently had a teething problem while we were out working in the garden, and decided to work it out on the wooden door's mullion. The mullion has been rather decreased in the ...
3
votes
2answers
2k views

How can I make trapezoid-shaped wood board (beveled edges)?

The reason why I want this is somewhat difficult to explain. I basically am looking for moulding-sized planks that have a trapezoid shape like this: That's the best trapezoid shape I could find, ...
3
votes
1answer
2k views

Where can I get a threaded wooden/metal rod for an adjustable piano stool?

I want to make a height adjustable stool, like a piano stool, of the simple screw/rotate type, but I don't have a lathe (or anything like enough skill) to turn a thread in wood myself. Is there ...
3
votes
2answers
133 views

What tool should I use for carving deep shapes in a desk top?

I am starting a DIY project to create a standing desk. Part of this project involves installing some electronics in the wooden desktop itself. I need to make the following cuts / carvings and am ...
3
votes
1answer
645 views

What type of wood filler should I use?

I'm starting a project to build my own solid body guitar. I received the body and its made from ash. It needs to be filled (the grain is very porous). I hear that I need wood filler for this. The ...
3
votes
2answers
1k views

How to seal an indoor wood planter box?

I'm planning on building a wood planter box for some edible herbs. (Similar to this; in Maple and a bit more squarish.) I already plan to glue the wood with Tidebond III as it is waterproof. My ...
3
votes
2answers
173 views

Building custom cigar box - is there a MAYA or 3DSM to wooden cutout service

I am looking to build a custom cigar box, and was wondering if I were to design it in MAYA or 3D Studio Max and the figure out all the different pieces I would need. Is there a metal, plastic, or ...
3
votes
1answer
87 views

How do I repair splits in a wood cabinet going with the grain?

How do I fix 2 narrow splits on a wooden clock cabinet? The splits are following the grain pattern. I want to fill them in and not notice them. Should I use a colored wax stick?
3
votes
1answer
1k views

How to drill a grommet hole through a desk?

I have a wall desk that hides away 2 power outlet on the wall. How do I drill a grommet hole that is wide enough to run cables through and cover it with plastic wire cover. What sort of tool do I ...
3
votes
1answer
113 views

When to use a spline vrs a biscuit joiner?

I know how to do either, but want to know if one is better than the other for particular joints (if so, what cases). Or is it just a trade off between time / labor (spline) and ease / cost (biscuit ...
3
votes
3answers
178 views

What are my options for framing a thicker than average piece of artwork?

I have a piece of signed TV artwork that is mounted in cardboard frame aprox 1cm deep, that i want to hang on the wall. I've had a look round and most of the frames i've found aren't deep enough to ...
2
votes
3answers
2k views

Where should I look to rent time on a router table?

I have a woodworking project which requires a CNC router table. It would need a decent sized table for the 36" x 28" panels. Somebody that spends thousands of dollars on one of these machines must ...
2
votes
4answers
414 views

How do I sharpen wood lathe tools?

I've had a lathe for about a year now (I have the JET 1442 with variable speed) and love it but noticed that I really suck at keeping a nice sharp edge on my tools. I have a small bench grinder I use ...
2
votes
4answers
1k views

Re-oiling a wooden worktop

I've sanded down a wooden worktop and I'm attempting to re-coat it. I've done 5 thin coats of oil so far, a day between each, but it's still quite dull compared to previously. How many coats should I ...
2
votes
3answers
1k views

How can I shave about 1/8“ from a 8'x3/4”x1 1/2" strip of oak?

I attached a 8'x3/4"x1 1/2" strip of red oak to the edge of multiple layers of plywood in order to make the plywood more rigid. Altogether, the three layers of plywood are 1 3/8" thick. This means ...
2
votes
3answers
230 views

Good technique for squaring-up hardwood edges?

I'm building a small shelf for organising my desk, using sections of 42mm*19mm hardwood. I've cut the pieces to appropriate length using a hand saw, allowing some tolerance for the kerf. Now I'd like ...
2
votes
3answers
880 views

Should I use a hammer or a mallet when driving a chisel?

I'm planning to install a lock into a wooden door and I'll need to cut various holes for the lock body using a chisel. I'll need to use something like a hammer or a mallet to drive the chisel and I'm ...
2
votes
2answers
249 views

How can I cut/route a small, straight slot through a piece of wood?

While I'd like to keep this question as generic as possible, I specifically want to cut a slot that's 1/2" long x 3/16" wide all the way through a piece of 3/8"-thick oak. My primary options are ...
2
votes
2answers
1k views

real dimensions of 2 by 4 in inches/centimeters [duplicate]

Possible Duplicate: Why are 2“x4”'s really 1.5“x3.5”? Just by looking at a 2 by 4 plank I can tell that it is neither 2in × 4in or 2cm × 4cm. What are its real ...
2
votes
4answers
311 views

How can wood be bent this way?

I am working on a DIY wood project and want to bend a piece of wood similar to the curves seen here by the artist Gustav Reyes, who is known for his jewelry pieces such as this finger ring: Click ...
2
votes
2answers
437 views

Which technique of wood joining is the best for joining these boards of a small table?

I want to join these four 1.8 cm thick beechwood boards as one can see on the picture. My idea is to join at the B points with biscuits but I’m not sure what to do about the A points. It needs to be a ...
2
votes
3answers
432 views

How to make a Bevel Lap Splice joint, for connecting a portable floor?

I'm new to woodworking, and I've read that I could potentially create this joint using a table saw, jointer, or even a circular saw - but I do not want to rent/purchase one and find out that I can't. ...
2
votes
1answer
590 views

How to patch a hole in stained wood (oak) so that the patch material matches the wood as close as possible?

I drilled a 1/2" hole into a stained oak board and I want to fill it so that it's as minimally noticeable as possible. Here are the three options I've found so far: Wood putty. This means I'd have ...
2
votes
1answer
726 views

Portable home bar plans?

I'm moving into about a 1500 sq. ft. house soon and I would like to build my own portable bar that I can store beverages in. It should be long enough to put a couple stools in front of where people ...
2
votes
4answers
158 views

Guidance needed for cutting rabbet

As in this question about making box shelves, I am looking at making some shelves and need some help. I've found this site describing how to make the shelves but need some pointers on what tools I ...
2
votes
3answers
109 views

How can I build a two-legged table?

I am building a rectangular coffee table and want to build it with two legs The table top will be 120cm x 100cm (approx 47x39inches). The table height will be 40cm (approx. 16 inches) the idea is ...
2
votes
1answer
55 views

Are there any advantages to using s-clips for attaching a table top instead of a right angle bracket?

I'm looking to build the "Simple, Sturdy Workbench" from Getting Started in Woodworking, Season 2 - http://www.startwoodworking.com/getting-started. The design attaches the bench top to the frame ...
2
votes
2answers
585 views

How can I cut detailed wooden monograms out of 1/4 inch plywood?

What is the best way to cut a 20 inch vine (font) monogram with a circle around it, out of 1/4 inch Baltic birch plywood? I have seen them everywhere but I'm finding it extremely difficult to cut out ...
2
votes
2answers
85 views

How to clean a 100 year old piano

I have recently inherited a 100 year old piano that has not had any love in a long time. I have tried to clean it with vinegar and water but it persists in being VERY sticky. I don't want to harm it ...
2
votes
2answers
239 views

What tools should I use for hand carving and whittling?

I have been hand-carving hunting bows (ie: simple selfbows, straight backed bows, steamed static recurve tips, etc) for a couple years. I used to do all of my carving with a set of nice drawknives and ...
2
votes
1answer
50 views

How do I tune a Bandsaw so the blade doesn't drift?

I just bought a 9-inch Delta bandsaw and I know there are some things you have to do to get it tuned right so the blade doesn't drift etc., but I have no idea what those are. What are some tips I ...
2
votes
1answer
66 views

Why did my third coat of polyurethane finish “buckle”?

I'm refinishing a table I built about 10 years ago. I put 2 layers of gloss polyurethane down and sanded between coats. All was fine at this point. I gave it another light sanding and put a third ...
2
votes
4answers
208 views

Simple software for stress analysis of wooden structures?

I'd like to develop an intuition for how the stresses are distributed in a simple wooden structure (in this case, a bunk bed). One option is to spend years building bunk beds, but I'm hoping I can ...
2
votes
2answers
171 views

How do I make this Raspberry Pi box?

I found this gorgeous laser-cut box on Amazon for my Raspberry Pi, and wondered how I could possibly make one of these myself. Can someone help me?
2
votes
2answers
21 views

How do I fix bare spots on my table after applying polyurethane?

I polyurethaned my table and when it dried, it had spots. That is the best way to explain it. It looks like the eraser-sized spots are bare wood, almost like something made the polyurethane push away ...
2
votes
1answer
45 views

How important is the scoop cut in a drop-in joint?

I've been reading up on joints, particularly drop-in joints. Some of the drawings have a curved cut on the underside leading up to the tenon, sometimes labeled a "scoop cut". Curves make ...
2
votes
1answer
151 views

Can a drywall screwdriver be used as a regular power screwdriver?

I will be buying (or renting) a drywall screwdriver, I want to save a bit and have a tool that can be used for woodworking later, can it be used? Is it too low torque (I guess it is about 7 Nm) for ...
2
votes
2answers
120 views

How do I clean reclaimed wood from construction?

I'm building a house (brick, cement and concrete) and I have a big pile of wood used for beam and pillar molds. How can I properly clean cement off wood? I think it should be very damaging to blades ...
2
votes
2answers
574 views

How can I build an insert on a desk that adjusts the height of a sewing machine?

I'd like to take my executive desk ( now sewing table) and cut out a piece of it to use as a support for my sewing machine. I want the sewing machine support able to lower the machine to table height, ...
1
vote
3answers
205 views

How can I make tongue and groove cuts with only a radial arm saw?

I'm pretty new to woodworking and I don't have a lot of tools. I'm working to make pieces to sell and buy more tools as I go. I don't own a table saw, but I do have a radial arm saw. Has anyone ever ...
1
vote
2answers
148 views

What is the best way to level a tree log?

I'm making an end table/floor lamp from a 3 ft cut log. What's going to be the easiest or best way to level the bottom and top of this piece? I thought about throwing it up on some saw horses and ...