3
votes
3answers
41 views

How to repair a crack along the grain in a solid block of wood from a single tree?

Approximately 3 years ago I purchased a slice of a log, approximately 50 cm (~1.5') wide at the widest place, approximately 2.5-3 meters (~9-10') long, and about 4-5cm thick (I don't have exact ...
1
vote
2answers
74 views

What material is used to fill cracks in wood that looks black afterward?

When looking in the more stylish furniture shops, they often have very large tables (e.g. 10cm thick x 1m wide x 2-3m long, made from one piece of lumber. Understandably, such pieces often have come ...
2
votes
5answers
128 views

Improving piece of furniture

I have a piece of furniture that is in need of some improvements. This is the piece: As you may already see, there are a lot of light marks in it. If we look closer to the surface, this is how it ...
5
votes
3answers
281 views

How would I go about identifying and matching this wood stain color?

I inherited some wooden furniture (which I believe to be oak) a few years back and was looking to add a couple of pieces to it. I want to try and get close to the same color, but I have no idea what ...
1
vote
1answer
79 views

Reinforce chair stretchers with screws?

I have a set of dining room chairs and a table. Some of the chairs have their stretchers come loose. They were just held in with glue. Two years ago, I re-glued them and applied pressure with clamps ...
0
votes
2answers
881 views

Wobbly desk with IKEA tabletop and IKEA legs

I seem to have an issue with the table top and legs I have purchased from IKEA. For reference, the table top I purchased is here: http://www.ikea.com/us/en/catalog/products/50106773/ and the legs I ...
0
votes
2answers
111 views

Is it possible to cut a threaded hole in wood?

Is it possible to create a threaded hole in wood? I'm making a kitchen island where the structure is 20mm threaded metal pipe (water pipe). I can either get flanges to connect it to the top or thread ...
0
votes
3answers
55 views

Exactly measure lumber for cabinetry

I am working on a bookshelf which, due to the way I am building it, requires some of the pieces to be exactly measured to within 1/64th over 4-5 foot lengths. Obviously no yardstick is so accurate. ...
5
votes
1answer
226 views

What is this type of traditional adjustable shelf support called?

I saw these on a bookcase in a shop today, but don’t know what they are called. Also is there an easy way to make them, or can they be bought “off the shelf”
1
vote
2answers
148 views

What is an aesthetically pleasing way to add lateral support to a loft bed?

I'm building a loft bed, and while I have a pretty good handle on the surface, I'm still trying to figure out the posts. Two adjacent sides are against walls, so I could put in diagonal beams, or ...
0
votes
0answers
132 views

Can turnbuckles hold a frame in tension?

I'm building a king-sized bunk bed using a loft/joist design. Basically, I've got (see below): slats nailed into joists joists joined to headers with blind tenons headers joined to posts with blind ...
4
votes
3answers
1k views

Are plywood dovetails a good solution to building something that needs to be dismantled?

Are hand cut, plywood dove tails feasible? Assuming you can get "good" plywood, i.e. not the brittle splinter-fest I've seen around, is dovetailing feasible? I'd like to avoid using glue for the ...
3
votes
2answers
313 views

How can I clamp two 325 mm planks while gluing them together?

I have a base that is 650mm deep. I'm going to have to glue several planks together to get this depth and, eventually, the last two to make the 650mm base. The problem is, I don't have (and can't ...
1
vote
1answer
1k views

How do I determine the thickness of wood needed for a desk?

I would like to make some furniture. It'll hold my computer, some books and still need to be strong enough to hold the weight of me leaning on it etc. How to I calculate what thickness of wood is ...
1
vote
2answers
601 views

How to repair a small hardwood crack?

I have a maple bench that recently decide to crack. I'm not sure what's the cause. I'm guessing wood expansion due to humidity changes. Anyway, I've decided to look around for solutions on fixing the ...
1
vote
2answers
191 views

What is the best way to level a tree log?

I'm making an end table/floor lamp from a 3 ft cut log. What's going to be the easiest or best way to level the bottom and top of this piece? I thought about throwing it up on some saw horses and ...
2
votes
2answers
526 views

Which technique of wood joining is the best for joining these boards of a small table?

I want to join these four 1.8 cm thick beechwood boards as one can see on the picture. My idea is to join at the B points with biscuits but I’m not sure what to do about the A points. It needs to be a ...
1
vote
1answer
309 views

How do you build a bookcase around an outside or convex corner?

How do you build a bookcase around an outside or convex corner?
1
vote
2answers
474 views

How can I fix a big crack on an old hutch?

A full wood side of an older hutch has cracked, probably along the grain. It seems gluing was attempted (there was some dried glue or silicon-like substance in the crack) unsuccessfully. Can I fix ...
2
votes
1answer
789 views

Portable home bar plans?

I'm moving into about a 1500 sq. ft. house soon and I would like to build my own portable bar that I can store beverages in. It should be long enough to put a couple stools in front of where people ...
7
votes
4answers
11k views

What is the best way to shorten legs on a table and chairs?

A few years ago we bought a "bar height" kitchen table and chairs. It seemed like a good idea at the time but we hate it now. It's terrible to have to sit with your feet not touching the floor for ...
4
votes
1answer
662 views

Woodworking Plans for an Office Desk

I am looking to build a desk for my office (L-shaped), but I am rather new at woodworking. I have the tools, and this would be a long project, but have no idea where to start. Are there any good ...
4
votes
3answers
1k views

What is a good plan for building cube bookcases with basic tools?

I don't have a table saw or a router or anything like that. I do have a circular saw, and a drill. I could probably justify buying a tool like a Kreg Jig or something like that for this project.
3
votes
2answers
1k views

How to cut curved legs for a table

I'm planning to build a bed-side table and wish to build it with gently curved legs. I'm planning to recycle wood some old hardwood doors by cutting the blocks out with a circular saw, then cutting ...