For questions involving wood as a construction material, either as lumber or finished features of a home.

learn more… | top users | synonyms

6
votes
3answers
634 views

How to connect wood to concrete

How can I attach wood to concrete in this bench?
1
vote
3answers
204 views

Any ideas for cutting door bottoms on pocket doors?

What can I do about pocket doors that are blocked by floor tiles? Could you cut out the bottom (1/4-1/2 inch) on a pocket door while it is still in the frame? What tools would you use? How would ...
0
votes
0answers
83 views

Building a 16 by 20 wood patio with tar shingles

I have 2x6x16 rafters hooked in to the side of my house. There will be approx. 12 of these. I have three 6x6x8 post that will be cemented in the ground. As of right now I have a 4x6x20 going across ...
5
votes
2answers
1k views

How can I plane the edges of plywood?

I'm working on an 8ft x 12ft climbing wall. I have 3/4 inch ACX plywood attached to a frame. Since the frame isn't perfectly square, the plywood overlaps on the edges (up to about 1cm) so I need to ...
3
votes
1answer
411 views

How to fit a new door in a narrower frame?

I would like to replace a door which has non standard dimensions. The door itself is old, 8 cm wider and 5 cm taller than current doors. It is also very expensive to order a new door for these ...
5
votes
2answers
426 views

How to fix unevenly stained maple wood vanity?

My bathroom vanity was not properly stained. It is not even. The edges are still showing the original light maple color. There are paint-like drips everywhere. I doubt that it has been sealed because ...
5
votes
3answers
3k views

What materials do I need to install pantry shelving?

I'm installing shelving in my 5x5 kitchen pantry. My plan is to run 1x2 strapping on the back edge and left/right sides of each shelf, then use 1x12 boards as shelves. I'm considering poplar for the ...
1
vote
0answers
32 views

Remove gloss from wood

what is the best way to remove a layer of clear varnish from my garage doors. I need to get them ready for winter and would prefer to stain them but it will not paint over the laquer very well. Sand ...
0
votes
2answers
169 views

PC in desk build

I'm working on modifying an existing table to hold 2 PC's under it horizontally. The PC motherboards will have to be placed on a 1,200mm X 400mm X 18mm countertop that will be connected to 2 other ...
0
votes
2answers
98 views

Gas fireplace to wood burning

I would like to know if my current gas fireplace can be converted to a wood burning fireplace. The house has a masonry chimney but I have not done any inspections yet. If it can be converted how would ...
1
vote
3answers
1k views

How can I stop a desk from vibrating when I type?

Yesterday I finished building a corner desk for my home office. I have no previous experience with woodworking, but I thought it would be a fun project. The end result is actually pretty good, the ...
0
votes
1answer
284 views

Can I just cut this part of the door frame out and replace it?

I finally hung these doors I found at a second hand store. I am a total amateur so please hold back your giggles. No need to explain how this happened, it was a dumb DIY idea. I just need a fix in ...
6
votes
1answer
466 views

Detecting mold with a blacklight

I've heard anecdotally that mold will glow green under a black light (UV light). Is this true? There's a room in my house with a musty odor, and I'm trying to determine the source of the smell. ...
23
votes
4answers
3k views

What is the best tool for cutting up scrap wood?

I have some wood left over from building a patio, mainly some planks. Normally when I'm creating firewood, I just use an axe a split the wood, but these are too long for that. I really don't want to ...
3
votes
1answer
429 views

How to paint a wood house?

I'm looking for good resources for painting a wood house. I'm looking for the proper tools and techniques. I don't want to hire somebody to do the job, I would like to do it myself. I just need to ...
4
votes
3answers
303 views

Is it possible to find 4“ x 8” lumber?

I'm putting in an end-grain floor in my house. The idea is that you cut normal dimensional lumber into 3/4' "bricks", then lay them like tile. What I'd like to find, however, is 4"x8" or even 4"x6", ...
0
votes
1answer
322 views

How can I make a sturdy lightweight box?

I want to build a box that is lightweight, but sturdy. At my disposal I have a laser-cutter, which I want to do the cutting. My plan is as follows, but I have never done this. I have no idea if this ...
3
votes
1answer
100 views

How do I repair splits in a wood cabinet going with the grain?

How do I fix 2 narrow splits on a wooden clock cabinet? The splits are following the grain pattern. I want to fill them in and not notice them. Should I use a colored wax stick?
3
votes
1answer
2k views

What is the difference between 'planed square edge' timber and 'planed all round'?

I am buying timber to use a curtain batten, between the rail and the wall. So I want the edges to be flat. I see wood sold as 'planed all round' and 'planed square edge'. What's the difference? Which ...
2
votes
1answer
197 views

How to build a wooden ladder for a loft bed?

I want to build a five foot ladder for my 6 ft loft bed that's being cut down to 4ft tall because it's too close to my ceiling. My bed is going to be in front of my window which is on my shortest ...
1
vote
1answer
104 views

What type of wood is this?

I've started my first home renovation project and I've stained this floor, after doing this I was told (by an amateur home renovator) that I'm not supposed to stain that kind of wood. Could anyone ...
2
votes
2answers
1k views

How do I clean dripped paint from a wood floor?

I've painted the skirting boards in this room and the paint has dripped on to a pretty fresh stained and varnished floor. How can I get these paint marks off the floor without damaging the new stain ...
4
votes
3answers
289 views

Why do decks and porches have cracks between the boards?

Is there a functional reason, like helping with rainfall or snow, or is it more of a cost issue? Are there decks that are solid pieces of bonded wood?
2
votes
2answers
134 views

Is there a way to reduce the moisture content in wood in a short period of time?

I've purchased some timber from a local builders merchant in which I'm going to built a desk with. I've already done this once, and experienced wood shrinkage due to the moisture content being too ...
6
votes
3answers
169 views

How to prepare & paint a porch with lead paint?

I'd like to repaint my 100-year-old wooden front porch. It almost certainly had lead paint at some point. I would very much like to avoid stripping it, or any other procedure that might mobilize the ...
0
votes
0answers
207 views

How to hang shelf on 2cm thin wall?

I would like to somehow saw out a wood board that fits into the corner as seen on the picture below. The problem is that both walls are only 2cm thin. The shelf needs to be able to hold a pair of ...
2
votes
3answers
118 views

What's the best way to recreate exterior wood trim?

I have some decorative wood pieces on the front of my house that are old and falling apart. I took them down to recreate them anew. Someone suggested I could trace them and cut out new ones in the ...
1
vote
1answer
172 views

advice for cantilever on temporary, free-standing wood structure

My daughter wants a piñata at her 6th birthday party. Unfortunately our back yard has no convenient tree limbs or other ways to hang the piñata, so I want to DIY something to hang it from. I'd prefer ...
4
votes
1answer
198 views

What should I build a bench out of?

I want to build a bench with a 450mm overhang from the legs (long story why I need the overhang, and I already have the legs which are heavy duty steel monsters). The bench will not hold anything ...
2
votes
2answers
109 views

Can my garden furniture be saved?

I have some hand me down wooden furniture. Unfortunately, with multiple moves and births in the last few years, it has gone a unloved. The wood seems very weak, and is brittle when dry. One beam ...
1
vote
1answer
395 views

What's the height limit of a wood framed building?

Using conventional light framing construction techniques, what is the maximum height of a wood framed building (in floors above grade)? I'm looking for any limitations in current building code, and ...
7
votes
4answers
5k views

My house has steel “2x4s” in the walls, can I hang cabinets, a TV, or some other heavy item from them?

The question is pretty much all in the title: My house has metal "2x4's" in the walls. Can I hang cabinets or a TV directly on these metal studs? If not directly, is there something special I must do? ...
2
votes
1answer
60 views

Can uneven ACQ treatment be corrected on decorative objects?

I bought some "pineapple" post caps made of treated pine. When they arrived, I was taken aback to see, rather than an overall greenish tinge, splotches and patches of green. As my plan has been to ...
2
votes
2answers
274 views

How to fix this window on a stud wall?

We recently bought two of these windows on a garage sale of a local window provider. We were so happy to have found two windows of the same size with the right color on sale that we quickly bought ...
9
votes
1answer
7k views

How can I fix a hairline crack in a thin wood panel of an exterior door?

My 100-year-old house has a wooden front door made of thick wood ribs interspersed with 8 wood panels, each about 10" high, 8" wide, but only 1/8" or 3/16" thick. Perhaps the door originally had ...
1
vote
0answers
198 views

Sanding vs power washing vs chemical cleaning wooden deck for restoration

There seems to be various methods for cleaning and preparing a wooden deck for restoration. Some how-to's that I have read strongly advise against power washing. Some sources suggest a combination ...
2
votes
3answers
325 views

How do I remove multiple layers of paint from wooden entrance ledge?

Here's a picture: If I recall correctly I have already tried a chemical stripper years ago and it didn't work. What would be the easiest way to remove the layers of paint all the way down to bare ...
1
vote
0answers
122 views

I purchased a handmade tool box of unfinished wood with oil and grease stains, I can I clean it up?

I purchased a handmade toolbox, an an auction, made form an old peach crate and old velveta and American cheese boxes for drawers. It was used in a workshop and has oil and grease stains all over it ...
5
votes
1answer
408 views

What kind of repairs are prudent for a ridge board damaged by a falling tree?

The limbs of the tree punctured the roof in at least two spots, so we're already looking at repairs. Upon closer inspection within the attic, I noticed that the ridge beam is just slightly splintered ...
3
votes
3answers
971 views

Are plywood dovetails a good solution to building something that needs to be dismantled?

Are hand cut, plywood dove tails feasible? Assuming you can get "good" plywood, i.e. not the brittle splinter-fest I've seen around, is dovetailing feasible? I'd like to avoid using glue for the ...
3
votes
2answers
288 views

How can I clamp two 325 mm planks while gluing them together?

I have a base that is 650mm deep. I'm going to have to glue several planks together to get this depth and, eventually, the last two to make the 650mm base. The problem is, I don't have (and can't ...
4
votes
1answer
2k views

How is a floating desk top supported against the wall?

Example of a floating desk top (courtesy of Phil Curtis): With increased height, it'd be one of simplest standing desk designs, and I am planning to do this at home. But, I am not sure how ...
5
votes
2answers
296 views

How can I build a lamp like the one I saw in the store?

My Fiance and I were walking through Target to find a lamp for the corner of our living room. We saw this one that we kind of liked But the price was way too high and the panels were too small. I ...
3
votes
5answers
3k views

How can I block or fill out a letterbox hole in my door?

I have a letterbox in my front door that is never used, so I would like to remove it and fill the hole, preferably so it doesn't look like there was ever one there. Or insert something that fills the ...
1
vote
1answer
274 views

How to repair solid wood cabinet finish after fire?

After a small kitchen fire in which the cabinets got fire damage, but did not actually catch fire, we repaired the walls, but are now left with a cabinet that looks (not too) bad. The black spots are ...
3
votes
2answers
142 views

What kind of store sells wood that isn't pine or MDF?

In Australia, there are 2-3 major hardware stores (Bunnings, Masters, Mitre 10), all of which sell pretty much the same Pine wood/MDF/particle board from the same suppliers. I'd like to work with ...
5
votes
1answer
6k views

How do I build a corner bench for my deck?

I am totally new to DIY and wanted to take my first steps with a simple project - a corner bench. I have decking outside already, and want to use the same decking wood for my bench. Something similar ...
11
votes
4answers
3k views

How can I attach two pieces of wood in an invisible way?

I would like to attach a thin tree trunk to a flat smooth piece of wood, in order to create support for a very heavy shelf. Any suggestions on how to do it, while leaving a minimal outside marks? ...
6
votes
2answers
346 views

How do I screw two posts together so that they look seamless and can easily be taken apart and put back together?

I would appreciate help so much! I am trying to make a 'collapsible' arbor if you will. I would ideally like to saw my large birch posts in half and make them screw back together in the center, but I ...
4
votes
3answers
285 views

What guidelines exist for the number of screws needed to attach two pieces of wood?

Are there any guidelines or rules of thumb for how many screws I should use when screwing two pieces of wood together? For example if I have a 2cm x 10cm plank I want to screw onto a 10cm x 10cm ...