For questions involving wood as a construction material, either as lumber or finished features of a home.

learn more… | top users | synonyms

0
votes
0answers
53 views

How should I hang two single swings on an apartment patio?

I want to hang two single swings on an apartment patio, side by side. I have an apartment above me, so I know cement is there but it is not a sturdy cover (my ceiling). I want to run a 4 X 4 across ...
2
votes
4answers
125 views

What is the proper method to creating butcher block for a computer workstation?

I've been looking into creating my own custom computer workstation and for the top I wanted to create butcher block but I am needing it pretty thick to be able to hold the weight of servers, monitors, ...
0
votes
1answer
64 views

Is plywood or dimensional lumber better for repairing notched joist?

During a recent remodel, I came across a 3 inch deep by 5 inch wide bottom notch in a 3x10 (the beams are that old!). I must say, i'm just a diy'er and even I was beside myself that someone would do ...
0
votes
0answers
202 views

Load bearing capacity of 2x6's for diy lifting cage

I want to build a custom power rack to safely perform heavy barbell exercises in my home. Commercial racks are too tall for my basement. Others have done this before: ...
0
votes
0answers
52 views

How can I pressurize stain into wood?

I'm thinking about how to stain the railing on my deck. What I have is the same design as the last three pictures on this page. I'm going to take the glass out before I stain, so there is some ...
1
vote
3answers
56 views

How do I get started removing this wood frame?

This is a frame inset into this old leaded-glass window I'm going to restore. It is nailed into the original frame, and I can't get to any of the nail heads to get started. It's important that I ...
0
votes
2answers
167 views

Can you attach a post base to a brick patio?

Can you attach a lumber post base to a brick patio, just as like as to a concrete one? Is an additional concrete footer needed?
2
votes
2answers
112 views

Best way to create a simple and economic steam machine for steaming wood?

I want to build a simple steam machine for steaming wood to bend. To do this I must place the wood into a sealed PVC pipe and pump steam into it. The PVC pipe part is the easiest part. Producing ...
2
votes
1answer
252 views

What to use to finish my desk from IKEA?

This may be an easy question, but everything I am finding on the Internet is kind of confusing (I am a computer guy not a carpenter!). Essentially, I want to know what I could use to finish my ...
2
votes
1answer
73 views

Filling deep gaps at corners of maple flooring

I have fairly new natural maple 3/4" [about 4" wide] flooring installed. The installer was sloppy and where the flooring butted against doorways (no doors, just open frames), he should have side cut ...
6
votes
3answers
758 views

Hardwood floors cupping even after replacement

Let me start off by saying that I am NOT a flooring expert or installer, I am a homeowner looking for answers. About 3 years ago, my home was built in southern Louisiana with reclaimed/antique pine ...
1
vote
4answers
170 views

How to drill a minute hole on a wooden pendant without a drill?

I'm not a professional carpenter and I haven't worked much with wood before. I also lack proper tools. I made a heart-shaped wooden pendant for my girlfriend with a paper knife and smoothed it out ...
1
vote
2answers
172 views

How well does masonry blocks used in European home construction insulate compared to a well insulated American (wood) wall?

Are there any equivalents to the Building Science insulation reports done for the US/Canada done in Europe? I spent the last few weeks going over some properties that I will be rehabbing in France ...
1
vote
5answers
209 views

Possible to flatten warped wood?

I have two sections of 3x12" wood that have been out in the weather for a few years and are now bowed across the 12" width of the wood. The dip is pretty severe, maybe 1/2 an inch? It seems like ...
2
votes
2answers
245 views

Will silicone spray lubricant cause bare dry wood to swell?

If wooden parts are binding, will silicone spray lubricant cause bare dry wood to swell? The wood is not maple or oak or birch. It is some type of softwood, maybe fir or pine. The bearing surfaces ...
1
vote
0answers
106 views

What is the essential beginners tool box? [closed]

I have limited budget, and am a firm believer in buying good tools that last forever, and not budget tools that last 5 minutes. I want to be able to build some items for my garden, a few planters, ...
0
votes
2answers
57 views

Solid stain on untreated exterior wood

I am putting together a bar top on my deck, and don't want to use pressure treated wood on the top surface (as I understand it that would be ill advised for an eating area). An option I am considering ...
0
votes
1answer
122 views

Hang 3 flat-screen monitors from a tilted wooden beam

I have an attic with a part where the floor was removed to bring light to the living room. I'd like to have my desk adjacent to that emptyness, but there's no space on the desk to place screens so I'd ...
0
votes
2answers
104 views

Using wood filler on garden furniture

I want to repair some weather battered garden table, bench and chair set. It has had some in places, so I will be replacing the severely rotten sections, and scraping out the rot from the partially ...
0
votes
3answers
76 views

How can I bend skirting for a bay window?

We have a bay window in our living room with a fast approaching deadline for the carpet being fitted. We need to bend the skirting as it won't be as pleasing to the eye if we do it in chunks and our ...
2
votes
3answers
128 views

What is the best way to drive the hard-cut nail into wooden baseboards to prevent splitting?

I am installing my baseboards, and there is a section that must be attached to brick. I know, by experience, that the best nail for my type of brick is the hard-cut masonry nail (and not the fluted ...
7
votes
1answer
213 views

Is there a more rugged finish than Polyurethane for a heavy use table?

A few years go I sanded a stained table we had. Upon doing so, we discovered that it had really nice wood underneath. So instead of restaining, I applied about 4 coats of satin polyurethane. It looked ...
2
votes
2answers
178 views

How can I patch a rotting wood door?

I have a small rotting spot at the bottom of my back door and it's almost to the point where I could put my finger through it. I don't have the cash to replace the door right now, but what would you ...
0
votes
1answer
53 views

Speaker veneer challenge (wood repair)

So I bought great but slightly damaged speakers and I would like to restore them, I understand they won't look like new but I would like to try my best. The damage: The wood texture detail: I was ...
1
vote
2answers
245 views

How to deal with Carpenter Bees boring into my front porch?

I noticed a single "bumblebee" hovering in front of my front door for days. When my handyman was out doing some repairs, he told me that it isn't a bumblebee, but a carpenter bee. Then he showed me ...
2
votes
6answers
3k views

What is the best way to fill finishing nail holes on door and floor trim?

There have been a couple of similar questions but none for my exact usage or that provides a good answer. I consider myself average to weak on finishing wood work so would like to hear some good ...
2
votes
3answers
123 views

How thick should should wood be to hold 160 to 180 pounds over a four-foot span?

I want to paint the walls above my living room stairwell. The stairs are four feet wide. I'd like to cover the stairwell with wood boards so I can stand my ladder on the boards to paint the walls ...
2
votes
4answers
124 views

How can I contain epoxy while it sets up?

So I finally built my portable home bar but I would like to have a bottle cap bar top with epoxy coating. However, I do not want to add wooden edges to contain the epoxy when I pour it over the bottle ...
6
votes
6answers
1k views

How to SLIGHTLY widen bored hole in 2x6

I'm making a stand-alone pullup bar and I bored 1 1/4" holes in 2x6's for my 1" galvanized pipe (1 1'4" outside) to slide through. Only the pipe is definitely 1 5/16" (thank you, guy at Lowes) and I ...
0
votes
2answers
123 views

Can a butcher block countertop be rounded with a router?

Looking to build a custom workstation and I wanted to use something thick as my top so I thought about using a butcher block countertop from a chain store, along with an inexpensive router bit set to ...
0
votes
2answers
77 views

Wood slats for sound insulation

I have a bunch of reclaimed wood of varying thickness, most are 1.5-2" thick. If I cut them to fit between my studs, would that serve as a good sound insulator under the finished wall? Would I have ...
1
vote
2answers
154 views

How do I fit a solid wood mantle to an existing stone surface?

I have an existing, irregular river-stone fireplace and would like to fit a solid pine slab mantle to the surface. I have considered scribing the top and bottom surfaces of the wood mantle, but I do ...
1
vote
2answers
168 views

Black Holes Appearing in Oak Floor

I moved into my home in May 2013 and had the Oak Flooring sanded and re-treated as it was a bit stained from previous owners (the flat is only 5 years also thought so the floor isn't very old at ...
2
votes
2answers
101 views

How do I season wood on my own?

Just what the title asks. Earlier today a tree on our premises split in two in heavy winds. The tree is of a variety referenced 'सागवन' in the vernacular, and Central Provinces Teak else-wise - that ...
0
votes
1answer
152 views

How can I remove a retaining wall made of vertical landscape timber?

I have VERTICAL landscape timbers in the hard soil in the back yard and I want to remove them. What is the best way to remove this retaining wall?
0
votes
2answers
599 views

How can I prevent a wooden bed frame from creaking?

Our wooden bed frame is three years old. At first it was perfectly solid and silent. But lately it's started creaking whenever we get in or out of it, and it's become unbearably loud. The noise comes ...
4
votes
2answers
287 views

How to deal with seasonal expansion and contraction of wood indoors?

Some doors in my apartment are subject to seasonal changes, similar to what is described here. I made adjustments: shimmed some hinges, shaved off some material here and there with a planer, and the ...
3
votes
2answers
92 views

Does thining wood filler make it crack when drying?

I'm wrapping my structural beam and posts with 1"x "white wood" cut at a 45 deg and butted together to make my corners. well the problem is my crappy table saw and not so good table saw skills, Its ...
3
votes
1answer
138 views

How can I build a bed frame out of palettes?

I'm moving to a new house, and on a broke budget. I found this bed design online. I'd like to do this from scratch and perhaps use wooden palettes for the main structure (adding supplemental wood ...
0
votes
0answers
39 views

Exhaust/drafting plan for a new wood furnace install

i just purchased a wood burning furnace that is designed to tie into and supplement the main furnace which in my case is a geothermal unit. after spending a few days reading about "best practices" ...
1
vote
1answer
852 views

How do I turn my top-heavy headboard into a freestanding headboard?

I've DIYed an upholstered, king-sized headboard (5'x6'10"), but after trying to bolt it to the bed frame, I've realized that the bed frame is much too light to prevent the headboard from toppling ...
1
vote
1answer
394 views

How do I match the color of old wood with stain after a repair?

I had a need to do a repair on some wooden trim in a kitchen. The new wood is the same type and grain as the piece that was removed, but the color is considerably different. The old wood was cleaned ...
2
votes
1answer
214 views

How can I tell if this is wood or drywall?

I am trying to mount speakers on the topmost part as you can see here: Basically I am mounting it on that thin vertical area that you can see. Is this part wood or drywall? From tapping it, it ...
1
vote
2answers
303 views

Compound mortise and tenon joints on corners (ie. legs of a table)

I am playing around with the idea of doing a workbench that can be disassembled, using pinned mortise and tenon joints. I haven't found anything that could be used where two spans meet at a corner ...
3
votes
2answers
506 views

How do I fix hole on wood siding?

I installed a new outside light and took down the old light fixture. Now I have some holes on the wood siding. Some bigger area is about 1" to 1.5". What is the best way to patch them? More info: the ...
5
votes
2answers
260 views

How can I hide exposed countersunk screws in kitchen cabinets side panel?

How do I hide screws on the side of a kitchen cabinet wall that has slightly countersunk screws? I will be painting my cabinets black.
0
votes
1answer
71 views

Assemble and dissemble tools for vanity table

I am planning on building my girlfriend a vanity desk where she can apply her special make-up and all that lady stuff she enjoys as my anniversary gift. I have a concept in mind but one thing I know I ...
-1
votes
1answer
59 views

Not to apply polyurethane

I have finished applying a cherry stain to interior French door with trim. I am on the fence about applying polyurethane because I am not convinced that it will look good. Personally I like how it ...
0
votes
1answer
60 views

I have an old house (100 yrs) up off the ground and in the past year the wood floors have began to sag where the boards meet [closed]

I think my house is about 1oo years old, I have lived in it for 15 years and just in the last year the wood floor has started to sag or bouncy where the boards meet. I thought it was in the traffic ...
2
votes
3answers
874 views

What type of screws should I use?

I am going to build a set of shelves for my wall to hold my bead jars. The shelves are narrow 4" nominal and very close together 3" is the farthest apart they will be. I'm using quality pine ...