The installation of wire and/or electrical devices, to allow the transmission of electricity from one point to another.

learn more… | top users | synonyms

2
votes
2answers
16k views

What's causing the popping noise from my speakers?

Several weeks ago, I moved into a new home. In office, I have my computer set up with a set of media speakers (older model of Logitech Z-550's). Every now and then the speakers will make a popping ...
0
votes
2answers
708 views

How do I wire up a saeco magic deluxe coffee grinder to be a standalone coffee grinder? [closed]

I would like to make a standalone coffee grinder by reusing the grinder in an old broken down Magic Deluxe Espresso machine. My electrical skills are pretty limited but I thought I'd find an ...
0
votes
1answer
11k views

Why is my Australian light fixture wired this way?

I just want to replace it with a new light fitting philips tcg701 but there's way too many wires and I don't know why it was done this way.
1
vote
0answers
2k views

How do I wire a bathroom exhaust fan/light to two switches?

I could use a diagram to wire the following: a bathroom exhaust fan with light on two separate switches. I also need a 3rd switch for a vanity light and a GFCI. My power comes from the attic (12/2 ...
2
votes
2answers
711 views

How can I replace a single bulb light with a fluorescent fixture?

I would like to replace a single light bulb light in the closet with a fluorescent fixture. The bulb is wired with two black hots to the light bulb fixture and the white neutrals are wired together. ...
8
votes
1answer
2k views

How do I wire this motor with 240V?

I have 240 plug with a switch dedicated for Air compressor. I have compressor that supposedly can be wired for 240V 2 pictures show sticker and current wiring. How do I update wiring to make it 240V? ...
3
votes
2answers
5k views

How can I convert switched receptacles to half switched receptacles?

In my new house, I have two outlets which are both fully switch, and can be controlled by two different switches (three way of course). I would like to convert the outlets both to half switched, but ...
4
votes
2answers
682 views

How should I connect these two yellow wires?

I don't know what this cap is... is it ok to cut it off and splice the two yellow wires together as I have been with the previous splices.
0
votes
0answers
357 views

How do I connect up a ceiling rose in a 2-way switch circuit?

I removed a ceiling rose and forgot to at least take an image or draw the wiring before replacing it. It is part of a 2 way switch (the other switch is upstairs). However, the wiring colours are ...
1
vote
2answers
399 views

How can one properly and tidily install this hardware for internet access?

This picture shows what my new home has for the wiring necessary for internet access. Some of the wiring here isn't necessary---in fact, most of it isn't, just the telephone wiring. With an idea of ...
0
votes
1answer
113 views

What is this circuit board and how to I replace it?

I have two under counter lights in my kitchen which stopped working at the same time. I assumed some kind of fuse needed changing, and on opening the little box connecting them to the mains I found ...
6
votes
1answer
332 views

What is “workmanlike manner”?

I have to ask this because I have been doing a ton of electrical work in my house. Will get inspected soon. I am pretty neat - everything is stapled uniformly and ran at the same height- but I ...
7
votes
1answer
394 views

What are these clips on the wires in my junction box?

Are these clips just for protection? or are they connectors for something?
2
votes
1answer
1k views

How do I rewire an old light fixture?

I have an old pendant light fixture with a ceramic bulb socket that needs new wiring (the old cloth covered wires are falling apart). There is a copper colored screw and a silver colored screw in the ...
1
vote
2answers
811 views

Can I run a single 12 guage wire outside of 12-2 to provide power to a fan?

I have regular 12-2 wire going to a bathroom fan. Tell me about code issues with just running an extra 12 gauge shielded wire up to the fan so I can do the fan and light separate. Any restrictions, ...
-1
votes
1answer
2k views

How do you wire a light fixture with only black and white wires?

How do you wire a light fixture if from a light fixture that was already there and I have a white wire with smaller wires inside to use to install. The 2 wires are black, and one white wire. Why isn't ...
4
votes
1answer
416 views

Is it OK to have a GFCI downstream of a standard circuit?

I would like to extend a standard electrical circuit to the outside with a GFCI outlet. Can I install a GFCI downstream? This would be easier than running a new circuit back to the breaker panel.
4
votes
3answers
366 views

What material to use to close a too wide wire tunnel?

During the cold days I noticed a little draft coming from the light switch next to my house door. Removing the switch revealed that the tunnel for the cables was widened to fit the cables for the ...
3
votes
2answers
1k views

Which is the bare wire in a 12-3 gauge cable?

What purpose does the bare wire in a 12-3 gauge cable serve?
1
vote
0answers
197 views

Can I convert my front intermediate light (with only 1 wire) to a junction box with live, neutral and ground wires?

I want to change my entire front light housing because it is old and uses an intermediate-base light bulb. The new one I have purchased has black, white and copper wires. The old one only has a wire ...
2
votes
1answer
15k views

How do I wire a 3 gang switch in my new bath?

I am putting a basement bath in and I need help. I will be adding a new 20 amp circuit for the single pole outlet. Also, a 20 amp line for a 3 switch box. Switch #1 is for the vanity light, #2 is for ...
4
votes
2answers
1k views

How should I ground two switches in a handy box that were previously ungrounded?

I am replacing two light switches in my bathroom. One controls the light above the sink and the other controls the fan in the ceiling. When I took the old switches out, I saw that the three neutrals ...
1
vote
2answers
255 views

Can CFL bulbs in a fixture with a dimmer switch damage old wiring?

Our wiring is not functioning now after using a CFL bulb in a dimmable light fixture. Is it possible that use of the CFL bulb could affect our old wiring? We may have to replace the wire leading to ...
0
votes
0answers
269 views

Why did my ceiling light fixture stop working after adding an outlet on the same circuit?

I recently added a receptacle for hanging my TV on the wall. To do it I fished a wire through the wall and attached wires to an existing receptacle that's at a lower level on the same wall. This is ...
1
vote
0answers
412 views

Where can I connect the ground wire when replacing my oven heating element?

My old heating element finally burned out and had to be replaced. That element is not made anymore, but an appliance store gave me the part # for a replacement that works for that oven. I took out ...
2
votes
2answers
526 views

How should I tidy up loose speaker wires?

I have surround sound speakers with the speaker wires going up through the wall. The wire is fixed and doesn't slide in and out the wall. Now it's time to tidy it up! How much loose wire should I ...
8
votes
3answers
7k views

Can I use two wire nuts instead of one to connect 6 wires inside a 3-gang box?

Is it considered acceptable practice to use two wirenuts in a situation where it is possible to use only one but may be easier to use two? I have a three-gang box with six cables coming into it. The ...
2
votes
1answer
449 views

Can I upgrade my garage to 20amp service without a headache?

I have an unfinished garage which I am looking to upgrade the service to. Currently it is 15amps running through some difficult to access sub-ground conduit, but if I run the band saw plus the ...
3
votes
3answers
5k views

Why am I getting 50V at a light when the switch is off?

I am trying to put in a switch and a light it controls in a storage building and this is how I wired it. Click for larger view When I checked the wiring it registered 120V when the switch was on, ...
1
vote
2answers
1k views

How does one typically do “Old Work” with metal junction boxes?

I am trying to add a light fixture to a room. I have access to the studs in the wall (new wall being added to the room), but the ceiling is drywalled. There is no attic access. Unfortunately, the ...
5
votes
2answers
2k views

How can I find an interior wall from the crawl space?

I want to run some component cables from one room to another by fishing down the wall into crawlspace and then back up the other wall. When I'm under the house there's no way to tell where the inside ...
4
votes
2answers
653 views

Is there any NEC code requirement for how far off the floor Category 5 wiring must be run?

I am currently running conduit for Cat5e cable in the home office I am finishing off. Are there any rules in the code for how far off the floor Category 5 wires in conduit must be run?
7
votes
2answers
487 views

Do I need junction boxes where conduit containing data cables terminates?

I'm going to be running 1" blue PVC conduit from all my low voltage boxes to a structured wiring panel. My wiring panel will chase to the attic where necessary and I was wondering what the best ...
1
vote
1answer
5k views

What is the minimum distance that should be maintained between parallel electric and data cables?

I need to run some electric and data (coaxial, UTP Cat5/6 and phone) wires from one room to the adjacent rooms. I've read Can I run CAT5/6 cables parallel to electrical cables? but I understand that ...
2
votes
2answers
5k views

Can I extend the ground/bus bar in a main service to accomodate subpanel equipment ground?

I am about to replace the main service breaker panel in my house. The old panel (a 200amp Siemens 40-circuit) had bus bars that extended the entire vertical length of the box. The new panel I would ...
2
votes
1answer
4k views

How can I convert two recessed lights on a single pole switch to two separate lights with light controls?

I have a bedroom with two recessed can lights operating from one wall switch. I would like to add a ceiling fan/light to one of the outlets and convert the other to a track light with its own light ...
2
votes
2answers
1k views

There's a bunch of unshielded copper wire in a light switch - what is it and what does it do?

I was just replacing a faceplate, and noticed that there was a large amount of unshielded copper wire twisted together in the back of the light switch electrical box. The light switch box is a larger ...
1
vote
2answers
289 views

How do I extend existing 10/3 wiring to run a compressor that needs 12/2 wiring?

I am installing a new compressor in my garage. I already have 240V installed to run a kiln. The kiln is only used maybe 10 times a year. My thought is to splice into the 240V line to the kiln to run ...
2
votes
2answers
17k views

What is code for installing a dishwasher in the U.S.?

I will be replacing my dishwasher and I am curious what is the current code for the wiring of the dishwasher.
1
vote
3answers
274 views

How can I rewire this circuit?

In my basement, I am removing an existing fixture and planning on installing pot-lights. Previously when I have switched out a fixture, I generally find white + black + ground, which is pretty easy ...
5
votes
3answers
8k views

Are non-GFCI outlets that are downstream of a GFCI outlet ground fault protected if they are fed from the GFCI outlet's load side?

Are non-GFCI outlets that are downstream of a GFCI outlet ground fault protected if they are fed from the GFCI outlet's load side? If those non-GFCI downstream outlets were not fed from the GFCI ...
1
vote
4answers
9k views

How do I wire a GFCI combination light switch when power enters at the light?

I have a Leviton 7299-NW GFCI/switch combo The diagrams in a response to the question "How do I wire a GFCI/switch combo?" is helpful. But I want to see a diagram for a situation where the power ...
1
vote
1answer
653 views

How to trace mystery switches

Since I moved into my house last year there are a couple of wall switches that remain a mystery to me. I don't know what they do, if anything. What are my options for tracing these switches? I'm ...
0
votes
1answer
428 views

How can I get my thermostat C wire connected? [duplicate]

I have an older furnace, on the switch block I have Y,C.W,R and an unlabeled screw that connects to the shut off it looks like. I need to hook up a thermostat that needs the C wire. I have a spare ...
3
votes
1answer
951 views

Can I use my old service panel as a sub-panel when I install a new one?

The main panel in my building is 100 feet from the where the feed wire comes in from the outside meter. Can I install a new 200 amp panel where the feed line comes in and use the existing wire to feed ...
2
votes
2answers
3k views

Why does my GFCI receptacle trip when I connect the load wires?

I was trying to install a GFCI outlet and when I install it with the five wire setup with the line on top and load on bottom, the outlet continually trips. I made sure which wire was the hot-line and ...
4
votes
1answer
264 views

How can I bore a hole through a framing member, without causing a lot of damage to the wall covering?

I am putting in a new thermostat. I cut a 1" hole in the wall at about eye level. I have an endoscopic camera and i see that at about 3 feet off the floor there is a wooden board that runs parallel to ...
1
vote
1answer
1k views

Can I steal a neutral wire from another circuit?

I have some Z-wave light switches that I want to install; below is a link to the diagram for the light switches. Basically I can have all the wiring completed minus the neutral wire for the switch at ...
0
votes
4answers
7k views

How can I use a separate transformer to provide a C wire to my thermostat?

I Purchased the Honeywell WiFi Prog Thermostat to replace my Round Digital Honeywell Thermostat. I have separate Heating and Cooling (Heating is a Weil McLain Boiler for Hot water baseboard and Hot ...
2
votes
1answer
4k views

What are the codes for electrical wiring in attics?

What is the typical code for wiring in attics? I understand these vary but what's best practice? Can you just have electrical wires exposed with all the junctions, in junction boxes, provided all the ...