The tag has no usage guidance.

learn more… | top users | synonyms

0
votes
5answers
573 views

Router bit depth keeps decreasing/slipping down, where is the problem?

I inherited a black and decker plunge router from my grandfather. From when I first tried it the bit has always slowly receded back decreasing the amount the bit protrudes from the router base. This ...
1
vote
2answers
179 views

Is this the source of my hot tub leak, or just a symptom?

Background: I have a Galbocca 2-person Plug and Play HotSpa (tm?) that I imagine is quite old. It came with the house I'm renting, so I have no idea exactly how old it is, but the company doesn't ...
0
votes
2answers
91 views

Why does my garage door opener only click when the button is pushed?

My Quantum 3213 garage door opener only clicks when I hit the main button in the garage. The light comes on for 30 seconds or so, and then it blinks on and off. I've checked all the safety ...
0
votes
1answer
24 views

Aprilaire 560 repair

My Aprilaire 560 humidifier will do a bang click many times before it turns the blower on. I replaced the solenoid valve with a new factory part and it still does the same thing. What next?
0
votes
1answer
42 views

question about a gas furnace having to light repeatedly

I am new to this forum, but I will do my best to answer any questions I can (I am a general contractor with a background in engineering and residential construction and machine design) so, here is my ...
1
vote
0answers
22 views

How can I figure out exactly where a bathroom leak is coming from?

There's a small amount of water at the lowest point on my bathroom floor. It looks clear and doesn't have a smell. Lately, it's been showing up every day, whether anyone's taken a shower or not. ...
1
vote
0answers
48 views

HVAC - hot air flowing on both zones when only 1 zone should be on

I have 2-zone forced air heating, with separate thermostats for each zone. Normally, if the thermostat in zone 1 triggers the system to go on, the heat will only blow through the vents in zone 1. ...
1
vote
0answers
22 views

lost voltage to outdoor light fixture

have an out door motion decter light suddenly w/o voltage to fixture. I traced romex from mdl to an in ceiling down light in laundry room. down light works fine, switches on and off. am I shooting the ...
1
vote
0answers
82 views

Why does my Whirlpool washing machine stop after the wash cycle?

My scenario: Whirlpool washing machine, mechanical timer/dial. It will fill with water, agitate during the wash cycle and at the END of the wash cycle it (the timer) clicks and stops completely. ...
1
vote
0answers
2k views

Would this buildup cause “dHE” error on an LG Tromm dryer?

Got the machine off craigslist. During the drying cycle it stops and shows the error. The user manual tells that with dHE error I should inspect the water supply, if the water supply is within spec, ...
0
votes
0answers
64 views

Flashing LED down lights

Here's one for the master electricians. I just installed two new LED down lights and noticed this morning that when I turned them on they started flashing on-off at about a 1sec cycle. When I ...
0
votes
0answers
104 views

What can cause a Ceiling Fan to rotate slow at certain speeds

Home Ceiling Fan Specs: Make: Crompton Greaves (Dont remember the model) Years in operation: More than 7 years No of Speeds available: 5 speeds Issue #1: The Ceiling fan rotates slower at positions 1 ...
0
votes
0answers
125 views

sliding window with electric roller shutter doesn't fully close

I have this window which doesn't fully close. It stucks at some point while closing. I can hear its electric motor still working but something prevents it from fully closing. So half of the holes are ...
0
votes
0answers
68 views

GFCI circuit partially works

While making coffee using downstream outlet, it just stopped. My GFCI outlet works and it isn't disconnecting. The test button also works but downstream outlets don't. What would cause that? ...