Tool (n) - 1. A mechanical device intended to make a task easier, 2. equipment used in a profession, e.g., tools of the trade, 3. Something to perform an operation; an instrument; a means

learn more… | top users | synonyms

16
votes
8answers
13k views

How can I coil up a rope so that it doesn't get tangled?

When I get stuff for DIY projects, I regularly use rope to tie it all down to my trailer. When I coil up a rope for storage I wind it around my palm and elbow (on the same arm) then use the last ...
3
votes
1answer
246 views

Is it safe to mount a medium-sized air compressor to the floor to stop or limit vibrations?

I have a 220V 6hp 33gal oil-less horizontal air compressor that aside from being noisy rattles all over the floor. Stock Image: I would like to either mount it to the floor or build a small ...
2
votes
2answers
2k views

When extending a wrench using a breaker bar, should I connect the two with a spline bit?

Can I use my wrench/spanner which has a box end / 12-point spline, and connect a breaker bar using a 12-point spline bit to it to get extra leverage. Or is it more common to use extending bar/pipe ...
3
votes
1answer
1k views

What nap roller should I use for primer?

And does it matter, in choosing the nap, what the sheen of paint will be used over the primer? E.g. if I do my bathroom in semi-gloss using 3/8" nap vs living room in flat with 1/2" nap, should I also ...
6
votes
7answers
3k views

How do I join 2x4s without mitering?

I asked this question on the Bicycles site: DIY wooden bike rack — looking for plans I'm planning to build this rack out of 2x4 pieces of wood. It'll live in my garage. I'm looking to make a rack ...
3
votes
4answers
6k views

Can I mix brands of chainsaw chains?

I have a Stihl 260 chainsaw, with a 3/8" chain and a 20" bar. What criteria do I need to apply when picking a second chainsaw chain?
11
votes
2answers
1k views

How can I tighten a bolt in a circular hole?

I've assembled a set of swings, and am trying to tighten the nuts at the top. The trouble is that they are embedded deep inside a circular hole and I can't get to them with a regular spanner. What ...
9
votes
2answers
7k views

Can I use an 8“ dado blade set in a 10” table saw?

I have a 10" table saw... this is probably a stupid question, but can I use an 8" dado blade set in this saw? Is one only supposed to use 10" blades in a 10-inch saw? I read on some contractor's ...
5
votes
1answer
2k views

What units are the clutch settings on a drill?

I have tried looking around the internet for an answer - but I can only find articles that explain what the clutch on a drill does. I am very familiar not only with what they do but also with how ...
2
votes
3answers
3k views

Will a Dremel multipurpose bit cut through 1/2 inch polycarbonate?

Would I be able to use the Dremel multipurpose cutting bit (561) to cut patterns out of 1/2 inch polycarbonate (Lexan)? Dremel "experts" said no but I want to hear other people's opinions. According ...
1
vote
1answer
706 views

Can oscillating multi-tools be used for fitting pattress boxes

I have a bunch of pattress boxes to fit for light switches and plug sockets and was wondering if my oscillating multi-tool could be of any use. I have a Bosch PMF 180 E Multi. Can this be used to cut ...
1
vote
3answers
816 views

How to choose between chrome-coated and oxidation-treated tools?

How do I choose between a chrome-coated (nice and shiny) and an oxidation-treated (dark oxidized surface) tool, all else being equal - same steel, same design, same handles, just one has its metal ...
2
votes
1answer
159 views

Which tile cutter to use for commercial flooring tiles?

I am putting (vinyl?) commercial flooring tiles in one of my hallways. The product I've seen one guy (pro) use at a supermarket once was this: Now, that baby is $200+. I was wondering whether the ...
4
votes
1answer
1k views

How can I disassemble this old bathroom faucet to fix a leak, without damaging the decorative chrome piece?

Update 4: Once I followed Michael's suggestion I was able to remove the cartridge. Closest match was a Moen 1224, 131222. Inlet and outlet were very different, and rotation of valve was much greater ...
0
votes
1answer
11k views

What type of glue sticks to tiles?

I have some hooks that has a glued surfaced attached to it. They look like this, Image Courtesy: www.dhgate.com I bought a lot of them. Like 50-60. I used them almost everywhere. Mostly in ...
-2
votes
2answers
1k views

Why are cordless drill batteries so expensive? [closed]

I bought a combo drill & driver kit recently and I really love it, but it came with "XC" batteries that are 4Ah. I went to buy one of the slim packs because sometimes the large batteries are just ...
-3
votes
1answer
185 views

Do electric push activated screwdrivers exist? [closed]

I am looking for a screwdriver. I want it to be powered (electric, cordless). I want it to not be based on a trigger mechanism (in order to reduce repetitive motion strain). I want it to screw (or ...
2
votes
3answers
4k views

Can I use a rotary tool to sharpen knives and other blades?

Anybody used Dremel effectively to sharpen knives and things like chisels and scrapers? What kind of bits are good for that application? Also, what do you call an electromotor that is clamped to a ...
0
votes
1answer
319 views

Why can't Bosch Detail Sander be converted as an oscillating tool? [closed]

I recently purchased Bosch 1294VSK. It comes with several adapters for hard-to-reach areas. It moves in an oscillating motion. I contacted their customer service dept to ask if it could be ...
-2
votes
3answers
911 views

Where can I find a knife blade with no handle? [closed]

I would like to make a nice wooden handle for a knife, but I do not have the means of cutting out a blade shape from scratch. Where are some places I could look, or some search terms for a knife ...
6
votes
4answers
504 views

How can I prevent a screw from slipping on a slippery veneer surface when I try to screw it in?

When using a screwdriver this can be difficult as the screw tends to slip. Once the screw passes the veneer it is easy to finish screwing in... I'm looking for an easy way to get the screw past the ...
7
votes
1answer
1k views

What are “concretors' nippers” for?

I came across this tool called "concretors' nippers" I guess they are for some operations with concrete reinforcement, but can't find any details. What operations is this tool for specifically? ...
10
votes
1answer
6k views

What is the difference between a ball/pin detent and friction ring impact wrench?

I have been looking into getting an impact wrench for my car and I have noticed that any given model (at least the one I am looking at) has two versions. One version has a ball to keep the socket ...
0
votes
1answer
175 views

What is a “Holders/Sujetadores de Sujecion”?

I bought a package of locking peg hooks at Home Depot, along with some pegboard and other assorted stuff. When I got home, I hung up the pegboard. It fit just fine. I then attempted to attach my new ...
1
vote
2answers
443 views

Can you crimp a tubular lug without a crimper plier?

I want to use these lugs on my electrical installation, but I can only find pliers for up to 16 mm2 cables and the mains cables are 25 mm2. I found one store that carried pliers able to do up to 50 ...
129
votes
2answers
14k views

What is the purpose of these holes on my wire stripper?

I have been using this wire stripper for a while, but I have always wondered what was the purpose of those holes in the center and above LOOP, and those teeth on the handles.
3
votes
1answer
177 views

What is a jig?

What is the process called, when you create a shape of wood which will only be used during making the end product. Say if you want to glue 2 panels of wood together (butt them together) at a certain ...
1
vote
1answer
699 views

What is the life expectancy of a ratchet strap?

During my house move I used ratchet straps to secure a book-shelf on a roof of my car. That was well secured and worked out perfect. But the second time I have tried using the same straps, they did ...
1
vote
2answers
515 views

What should I consider when buying a USB inspection camera? [closed]

I have a slow leak in a stud wall; I know it is coming from 1 of 3 pipes. I can replace any of the pipes without breaking into the wall; however I need a way to find out which pipe is leaking. I ...
3
votes
2answers
1k views

Are cheap electric brad nail guns worth it for fixing mouldings?

I am thinking of creating some doors out of MDF that will have moldings fixed to their fronts, these will be glued on. I could try to clamp them somehow until the glue sets, but that sounds like a ...
3
votes
1answer
290 views

“Built-in corrosion inhibition” - Does it work? How?

I recently bought a new toolbox to tame the piles of tools I've acquired for general home maintenance in my first year of home ownership. It's the Kobalt 26" hammer box; good size, sturdy enough for a ...
3
votes
2answers
10k views

How can I clean sticky and dirty hand tool's rubber?

I have a hand tool - Needle-nose plier that had a rubber that is used as the handle. Currently, I managed to clean up all the rust on the metal and would like to clean up the rubber handle as it is ...
12
votes
2answers
736 views

How do I caulk where a caulk tube won't fit?

I've got some door moldings that are about 1 inch from the adjacent wall. A caulk gun won't begin to get in there, and pivoting the caulk tube up so it's nearly parallel to both walls still doesn't ...
5
votes
3answers
303 views

What can these bits work on?

I wonder on what kinds of things the second, third and fourth bits from the left can work? What kinds of things can the fifth and sixth bits from the left work?
3
votes
2answers
209 views

What size ratchets do I need to assemble some new equipment?

I recently purchased a power rack and various other bits and pieces for the home gym. In the instruction manual the nuts and bolts on the hardware list state the following sizes: 1/2" × 3 - 1/2" 1/2" ...
5
votes
8answers
2k views

How do I get the most torque out of a spanner?

Recently I tried to get extra torque out of a spanner when unscrewing a bicycle pedal by lengthening the spanner with a piece of pipe and the spanner just broke apart. I realize that this was ...
3
votes
1answer
227 views

What type of arbor should I use to fix this holesaw?

Where can I buy the arbor for this type of holesaw. The ones I've found are hex shaped. Could you recommend a n arbour that would fix this hole saw
4
votes
1answer
2k views

What are the key differences between a step drill bit and a knockout punch?

Both a step drill bit and a knockout punch seem to be very similar, in that they both make holes in a metal box. The step drill seems to have an advantage, since it can make several size holes using ...
5
votes
1answer
633 views

What are the names of these tools?

I wonder what names are for all these tools in the picture? How are they used and what are they used for?
9
votes
3answers
2k views

Miter saw advice and recommendations

I'm buying a power miter saw sometime this week; and early birthday present to myself. What should I consider and what brands do you all recommend? I'm not a contractor, web guy by trade, and do ...
2
votes
1answer
1k views

What is the best tool to grind down a smaller metal rod?

I am building this workbench and I have decided to recess the nut and washer inside the top of the bench, so that I won't cut/scape myself while I'm leaning up against it. Now my issue is that the ...
8
votes
9answers
788 views

Should I purchase single tools, or a tool set?

I now happen to need a wrench to make some changes to my bed. I also realize that sometimes I may need other tools in my life as well. I was wondering Which way to build one's own collection of ...
6
votes
1answer
2k views

How to stop a circular saw from locking?

I've been using my new circular saw for about a week. Today while making a plunge cut it just locked. It didn't get stuck on anything inside the board and it consistently locked every time I tried to ...
4
votes
3answers
5k views

What voltage/amperage garage circuits should I install for welding tools and an air compressor?

As a part of renovating my garage this fall, much of the wiring is being re-done. Since doing the work before putting up walls will be much easier now than adding circuits in the future, I'd like to ...
2
votes
2answers
6k views

What is the difference between an impact driver and an impact wrench?

Obviously impact drivers and impact wrenches are designed for different purposes, but since they both work on the same principle is there some overlap? Is a small cordless impact wrench just a ...
31
votes
7answers
3k views

Is it worth spending extra to get a nicer circular saw?

I'm doing some small projects such as building a workbench, and I don't have a saw to cut plywood with. I've got a 12" compound miter saw, so I don't currently need a circular saw for anything other ...
5
votes
2answers
1k views

Are either of these tools suitable for tightening the pipe union nut underneath a bath?

I'm having trouble tightening the pipe union nuts on some new bath taps I've fitted at my mum's house. I got everything out OK, and (because the previous plumber had put the hot tap on the right ...
2
votes
3answers
542 views

Inferring wire gauge from cable size

Is there any way to infer the gauge of the wires inside an NM cable from the size and shape of the cable? I reckon a round cable is generally -/3 W/G and a flatter cable -/2 W/G, but I do not know how ...
5
votes
2answers
5k views

Why use a screwdriver when we have drill/drivers now?

I'm wondering when should we choose a screwdriver. Can it be used to put screws in wood, concrete or metal without drilling a hole? If we need to drill a pilot hole anyway, why don't we just use ...
9
votes
1answer
5k views

Socket wrench: Is there an advantage of a 3/8“ drive over a 1/4” drive?

I notice that socket wrenches come in a variety of sizes. For homeowners and DIYers, it's common to see socket wrenches which come in two sizes: a 3/8" drive, 1/4" drive and sometimes 1/2". The 3/8" ...