0
votes
1answer
45 views

Are router bit imperfections normal?

I just got my first router and purchased some Freud bits for it. However, I noticed that a few of them have pitting at the base where the cutter joins the shank. Is this normal for router bits, or is ...
4
votes
3answers
530 views

As a beginner woodworker, should I buy a table saw or a band saw?

I'm just getting into woodworking and don't have any equipment, not even a bench. As a beginner looking to maybe make anything from small boxes to light furniture, should I buy a table saw or a band ...
3
votes
1answer
208 views

What router bearing can I use to reduce groove depth?

I order this 3/32 slotting bit from Amazon. Shank size 1/4, depth of cut up to 9/16. I only need 3/8 depth (slightly over is ok), but I could not find the right bearing. There are router bearing ...
1
vote
1answer
185 views

How can I test my drill and batteries for faults?

Apologies if this is off-topic. I was given a used standard cordless 12v drill and 2 batteries, without the battery charger. The drill didn't work at all with one battery, and just turned slowly for ...
-3
votes
1answer
159 views

Do electric push activated screwdrivers exist? [closed]

I am looking for a screwdriver. I want it to be powered (electric, cordless). I want it to not be based on a trigger mechanism (in order to reduce repetitive motion strain). I want it to screw (or ...
5
votes
1answer
895 views

What units are the clutch settings on a drill?

I have tried looking around the internet for an answer - but I can only find articles that explain what the clutch on a drill does. I am very familiar not only with what they do but also with how ...
1
vote
1answer
440 views

Can oscillating multi-tools be used for fitting pattress boxes

I have a bunch of pattress boxes to fit for light switches and plug sockets and was wondering if my oscillating multi-tool could be of any use. I have a Bosch PMF 180 E Multi. Can this be used to cut ...
1
vote
3answers
2k views

Can I use a rotary tool to sharpen knives and other blades?

Anybody used Dremel effectively to sharpen knives and things like chisels and scrapers? What kind of bits are good for that application? Also, what do you call an electromotor that is clamped to a ...
2
votes
2answers
2k views

Why don't they make wood cutoff blades for 4.5" grinder?

Many times I used a chisel to cut off a hard-to-reach piece of lumber, I was wishing I had an adequate blade for my 4.5" grinder, as I don't own an oscillating tool. Why is it hard to find? Is it ...
5
votes
4answers
8k views

What is a good way to cleanly cut through steel?

What tools can I use to get a clean cut through thin steel? Specifically, I have several mini beer kegs I need to cut the bottoms out of. I don't mind it taking a while, but my cuts are jagged (easy ...
6
votes
1answer
697 views

How to stop a circular saw from locking?

I've been using my new circular saw for about a week. Today while making a plunge cut it just locked. It didn't get stuck on anything inside the board and it consistently locked every time I tried to ...
4
votes
5answers
720 views

How do I choose a circular saw?

I've made do with hand tools for everything including the rare plywood job for several years now and I want to buy a good circular saw. I will not use it very often, but when I do it will be for ...
6
votes
4answers
1k views

Is there any way to replace drill batteries?

We have a great (Porter and Cable) cordless drill but the batteries are no longer commercially available. Amazon has a listing but it's been sold out for the last five years. Do we have any other ...
7
votes
2answers
1k views

Cutting a Custom Threshold: Best Tool for the Job?

I am in the process of creating a custom threshold to go from a tiled surface down to a carpeted surface. The tile is about an inch above the carpeted floor, so I decided to make a custom threshold in ...
3
votes
2answers
194 views

What size ratchets do I need to assemble some new equipment?

I recently purchased a power rack and various other bits and pieces for the home gym. In the instruction manual the nuts and bolts on the hardware list state the following sizes: 1/2" × 3 - 1/2" 1/2" ...
4
votes
1answer
675 views

How can I repair my bench grinder?

Received a relatively old black and decker bench grinder from a relative. It works, mostly. About 50% of the time it powers up but doesn't spin - hand cranking gets it going, whether it starts fine or ...
5
votes
1answer
523 views

Are there any tricks for using an oscillating multitool?

I recently got myself a Ridgid JobMax and I think I love it. I did spend quite a bit of time, however, trying to get through an old (100 year old home) 2x4 (dimensional). I don't know if the wood ...
13
votes
2answers
4k views

When should I replace a circular saw blade?

Is there a rule of thumb for how often a circular saw blade should be replaced? Is visually inspecting the blade condition enough?
2
votes
2answers
3k views

What is the difference between an impact driver and an impact wrench?

Obviously impact drivers and impact wrenches are designed for different purposes, but since they both work on the same principle is there some overlap? Is a small cordless impact wrench just a ...
4
votes
5answers
834 views

What's a good cheap sander to sand the ends of wooden blinds?

I need to sand down some wooden blinds because they are about a millimeter too wide for the old window frames they are going into. I'm trying to figure out a cheap and easy way to sand down about 6 ...
7
votes
2answers
5k views

Can I use an 8“ dado blade set in a 10” table saw?

I have a 10" table saw... this is probably a stupid question, but can I use an 8" dado blade set in this saw? Is one only supposed to use 10" blades in a 10-inch saw? I read on some contractor's ...