The technique tag has no wiki summary.
4
votes
1answer
81 views
How do you keep from dropping grout all over when tiling?
Finished tiling a tub surround today. Wife helped me clean up the grout...
My mix is like a creamy peanut butter. I read the directions. I use a float and drywall knife to apply. I buy the good ...
7
votes
3answers
471 views
What tools do I need to make a straight cut in laminated chipboard?
It's 38mm thick.
Next week I will need to cut it along a straight line, and I would like the cut to be as straight and clean as possible.
What tools do I need to do this ?
-1
votes
2answers
119 views
home building - the complete manual [closed]
I want to build my own house, with my own hands that is.
Problem: I have no idea how you build a house :)
Is there a complete reference on how to do it? How do you set the foundations, how are the ...
12
votes
2answers
437 views
What should I keep in mind when building my house myself?
I inherited a piece of land and want to build a house on it. Nothing fancy: one floor, 2-3 rooms.
Since I don't really have the money :D to build it "in one go", I'm going to build it over a longer ...
1
vote
1answer
631 views
How do I insulate around conduits and into difficult edges in my attic?
I am thinking about adding a little over a foot of insulation to my attics.
I understand that there shouldn't be gaps between fiberglass batts (I read that this can reduce efficiency by 25%, whatever ...
6
votes
2answers
1k views
How do I use precision screwdrivers?
I am talking about those small and narrow screwdrivers with a thin handle. I can't get a tight enough grip on the handle to generate enough torque to remove a small screw. Do I have to use something ...
3
votes
2answers
652 views
How do you determine the slope of a floor?
What are some methods for figuring out the slope of a floor?
I've always heard the slope referenced as, eg: "1/2inch over 6ft." - is this the normal way, and/or are there other common ways to say ...
6
votes
3answers
420 views
What tool and technique do I use to achieve this finish in plaster?
Our shed (in Switzerland) has an outdoor wall that is finished with plaster texture called crépi here which Google translates as roughcast. The plasterer here says it is impossible to replicate today. ...
4
votes
2answers
264 views
How do I remove a fence post from a Wedge Grip support?
I'm in the process of replacing my back fence. One of the existing posts was damaged (crushed) during a tree fall. After finally digging this out, I discovered one of these in it.
What I can't ...
8
votes
2answers
738 views
When drywalling, do the pros cover electrical boxes, or work around them?
This may be a bit of a subjective question, but I was just thinking about it. I've seen many electrical boxes that are full of drywall compound, often to the point of having to dig the wires out of it ...
5
votes
1answer
1k views
Proper way to cut a 2x4 using a miter saw
So I was just watching Holmes on Homes, and they were showing a quick close-up of cutting a 2x4, making two passes, cutting the top half first, then finishing it off: ...
2
votes
2answers
549 views
Building a mechanical Clock
this is probably off topic as it's not "home improvement", but still, it's DIY, so, here it goes:
I want to build a mechanical clock.
I've read technical things about how they work, this is not my ...
6
votes
1answer
419 views
Paper joint tape VS. Mesh joint tape
What are the pros and cons of each type of drywall joint tape? Are there situations where one should always be used over the other?
4
votes
1answer
331 views
How to paint a wood house?
I'm looking for good resources for painting a wood house. I'm looking for the proper tools and techniques.
I don't want to hire somebody to do the job, I would like to do it myself. I just need to ...
3
votes
3answers
183 views
Are hydraulics stronger against compression or tension?
I would like to use a pair of hydraulic pistons to raise and lower a surface that will hold about 150 lbs, and be capable of remaining in either fully extended or fully contracted modes for long ...
1
vote
1answer
268 views
How do I use a stopper-borer?
I need to bore a small hole in a rubber stopper (bung) like this:
I have a set of tools called stopper-borers like these:
But I can't figure out how to use them. Simply pressing on the borer ...
1
vote
1answer
102 views
Oil heater in a large room
I'm about to by an oil heater. One of the properties of a heater is the area of the room that the heater can heat. Say 15 m^2 or 20 m^2.
The question is: what will be if I use the heater in a larger ...
2
votes
2answers
244 views
Tips for texturing ceilings?
I'm getting ready to texture ceilings for the first time using an air-compressor / hopper. I plan to practice first on some old sample sheets of drywall I have laying around but was also hoping to ...
11
votes
5answers
2k views
Is there a technique or tool for consistently placing drywall screws correctly?
Is there a special technique or tool for consistently placing drywall screws correctly?
I'm using a standard Dewalt DWD115K (with no auto-stop mechanism) so I'm usually paranoid of going too deep ...
5
votes
3answers
1k views
Can quick-drying mud be used on the same drywall joints where slow-drying mud was used?
I think I phrased the summary/title poorly but essentially, I'd like to know if all drywall mud coats need to use the same type of joint compound for all coats or if I can transition to quick drying ...
2
votes
1answer
2k views
What are some tips/techniques for applying knockdown texture to drywall?
I'd like to get advice on applying knockdown texture and fixing my own mistakes in the process. The consistency I'm looking for is something similar to this:
As per an eHow article, I think the ...
7
votes
4answers
572 views
What should I do with a double gang box if I no longer need two separate switches?
We're relocating our TV to a side of our living room that has a power outlet controlled by a wall switch. The switch is part of a double gang box (1 switch controls the porch light, the other ...
3
votes
3answers
264 views
Dresser/Chest with convex front
I'm contemplating building a dresser and am looking at designs and such to get my creative juices flowing. Today I noticed that some dressers/chests have concave or outwardly curving drawers on the ...
4
votes
1answer
3k views
How do I fix a pocket door wheel track?
I have a pocket door that keeps falling off its track. The metal track has become warped and bent down in just one or two areas. When I slide the door along the track and the front wheel goes over ...
10
votes
7answers
349 views
How can I pour a concrete pad with a circular hole in it?
Essentially, I'd like to put down a concrete pad for a patio, but leave a couple of circular areas within that patio unpaved (for planting shrubs).
I'm familiar with the techniques for using ...
36
votes
9answers
5k views
Is there a trick to applying caulk using a caulk-gun?
Perhaps it is just me, but no matter how careful I try to be, any attempt to apply caulk or cement or anything with a caulking gun into a crack results in total mess.
The main problems that seem to ...
