Vertical member in wall framing.

learn more… | top users | synonyms

1
vote
1answer
252 views

Can I mount a 60" TV and mount weighing a combined 95 pounds to a drywall or plaster? [duplicate]

I cannot find studs on my firewall but, when I drilled a hole on the wall, it seems to me that either the plaster or drywall was thick enough (like 1/2"). Can I Mount a 60" TV and Mount Weighing a ...
2
votes
1answer
459 views

How can I mount a shelf above a closet door?

I would like to mount a wall shelf above a closet door in a small bedroom. I was thinking about using the Ikea Ekby shelf, which is 59" long (exactly the length of the sliding doors of the closet). I ...
1
vote
5answers
895 views

What's the strongest anchor for something heavy in double drywall?

I have a party-wall in my apartment-née-condo that seems to have two sheets of drywall installed against eachother. All attempts to find some sort of stud or resilient channel / furring strip have ...
1
vote
1answer
178 views

patching hole to be reused

I'm trying to mount a tv into my chimney walls. My TV is 65" and weighs in about 65"lbs or so. I drilled in 6 holes. 3 at the top 3 at the bottom with about 12" apart. I was going to use the strap ...
1
vote
1answer
121 views

How to fill an old window alcove?

In one of the bedrooms in my house (1930s), there is a sunken alcove where an old window used to be, the internal sill is still there. Whoever bricked up the window used bricks much thinner than the ...
0
votes
1answer
56 views

Electrical across studs in basement?

I have a small workshop that I need to add an outlet for. There's a light switch 2 studs away that I'll use for power. I have no plans to drywall this area of the workshop. Is it ok (against any ...
1
vote
0answers
168 views

Ceiling fan install - orientation of mounting bracket to slope of ceiling

I'm replacing a light fixture with a fan/light using a down rod mount on an angled ceiling. The frame studs run parallel with the slope of the ceiling. Manufacturer notes to install mounting bracket ...
2
votes
1answer
254 views

How should I build a low profile stud wall in a basement?

I'm considering several options for building out a wall in a basement. Unfortunately, due to the way that the stairs leading to the basement are positioned in my house and the spacing I have to build ...
1
vote
0answers
111 views

How should I build stud walls to make shelves in a room that has a sloping ceiling and floor?

We have a home that is 104 years old. There is a room that was added in the 1940's and built over a sloped roof from the rooms below. It is fully enclosed and we would like to add some shelving in the ...
5
votes
2answers
701 views

how critical are distances between studs?

I'm in the process of finishing my basement (east-central Minnesota, US). So far, I've put up a couple of wood stud walls... non-load bearing, simple partition walls. One one of these walls, the ...
1
vote
0answers
358 views

how to attach threaded rod to wall stud on hinge

How can I attach threaded rod to a wall stud so that it is on a hinge. The hinge axle will be horizontal so the rod can rotate up and down but not side to side. The one piece solution I have found ...
0
votes
2answers
97 views

polystyrene insulation over dryloc basement walls

I am a DIY beginner. If I am installing polystyrene over drylocked basement walls, do I need a vapor barrier? Do I put the studs on top of the polystyrene? So, from exterior to interior it would be:...
2
votes
3answers
539 views

replace stud that has vent pipe through it

I had some water damage in my bathroom and a few of the studs are rotted. I am assuming they need to be replaced. The problem is these studs have a plumbing vent pipe drilled through the middle of ...
0
votes
1answer
245 views

How to frame steel studs parallel to concrete ceiling “joists”

One of the drywall I need to hang runs parallel to the joists (concrete joists and slab above it), and I'm at lost on how to affix the upper tracks which would be between two joists. I've seen this ...
1
vote
1answer
2k views

Can I hang cabinets and shelves on metal studs?

I recently moved into a high rise apartment and need to hang some cabinets. The cabinets themselves weight about 20lbs and I'm thinking the stuff stored inside them will be around 40lbs. I know I ...
2
votes
3answers
459 views

Is it safe to shave off 1/8" from a load-bearing stud?

I am trying to install a small metal media cabinet in a load-bearing wall in my basement, but unfortunately the cabinet is about 1/8" too wide to fit between the studs. Is it safe to shave off a ...
1
vote
2answers
3k views

Trouble finding studs in garage

I have a new house, and the garage shares a wall with an interior wall... trying to hang a pull up bar on it, so I need to find the studs. I took pictures of the house as it was being built, but all ...
0
votes
1answer
153 views

How can I attach to drywall with aluminum studs?

First, how can I find the studs? My normal and good stud finders are mostly baffled. Second, what should I use to anchor into them? I'm thinking some sort of self-expanding toggle bolt?
0
votes
2answers
477 views

Is it safe to remove 2 “extra” jack studs to make a 60" wide door opening wider?

We went to install our new main entrance 60" door (replacing double-door with single door and 2 sidelights). After we received the new door and shaved out more of the sheet rock, we saw that there ...
0
votes
1answer
160 views

Can the knock test tell you whether a stud is wood or metal?

I'm thinking about wall mounting a television, so I've used a stud finder to locate several studs in my wall. Out of curiosity, I knocked on the wall in several places to see if I could hear the ...
2
votes
3answers
935 views

Mounting Full Motion Mount on a Single Stud

I've seen this question regarding a sheet metal stud, but my plan and situation are a bit different. I am curious if ananyone thinks this sounds secure: I have a full motion flat screen wall mount ...
1
vote
1answer
247 views

How can I hang a wall mount on misaligned studs?

So my wall mount teleco rack arrived. However my studs are 15" apart, not 16" so I can't put lag screws into more than one stud. I don't want to drill into the metal so close to the opening already....
1
vote
1answer
3k views

Will using concrete anchors in wall studs cause problems?

While installing a wall mount for a 48" TV, I realized I made a mistake. I drilled a ⅜ pilot hole in the wall stud and then installed the anchors provided with the mount that the lag bolts would be ...
2
votes
1answer
421 views

How can I secure a wall-mount server rack?

I would like to install a 2-Post 12U wall-mounted server rack in my utility closet. The rack will hold up to 200lbs. However, my equipment will be just under 180lbs. Most of the weight will be at the ...
2
votes
1answer
260 views

What can I do if I need another gang in a junction box but there isn't space in the wall?

I have a dual gang junction box installed in a space between 2 studs in the wall. I want to add swap the box for a 3-gang box to add another switch for a ceiling fan, however when I took the cover ...
3
votes
3answers
406 views

How can I build a table into an alcove?

I have this weird portion of a second bedroom where about 4 foot of it is 2 feet deeper than the rest of the wall. What I want to do is fix a butcher block in that space to use as a desk. What is ...
2
votes
1answer
369 views

How can I build a mantel around my fireplace?

I am new to posting on this site but have been reading it for a while! My wife asked me to redo our fireplace mantel. When I got the drywall off I noticed that the studs are not exactly uniform. I ...
1
vote
3answers
6k views

What do I do if drywall screws won't penetrate the studs?

We have begun a bathroom remodel project. All the studs were exposed by removing plaster, wood lath and old plastic tile. We began attempting to install the ceiling drywall first. We were able to ...
3
votes
2answers
948 views

How can I mount heavy stuff on wooden studs?

I want to replace my kitchen cabinets (shoddy DIY stuff, very rough) with some nice floating shelves. I tried to find information on how to mount heavy stuff to wooden studs but all I found were ...
1
vote
4answers
6k views

How can I remove a stud from a load bearing wall?

I want to remove a stud from a load bearing wall in order to recess my fridge another 3-4 inches. In doing so I will be removing the bottom plate, one stud from bottom plate up to height of the fridge ...
0
votes
2answers
395 views

How to mount a pull-up bar to drywall on resilient channels?

I'm trying to mount a pull up bar on a drywall. The wall is shared with another unit though,so there are resilient channels behind the wall, and so the studs are offset from the dry wall sheet. What's ...
0
votes
1answer
52 views

Which stud should I mount to if they are different widths?

I'm trying to mount a pull up bar to the studs behind my drywall. The studs are 16" apart, but seem to be of different widths. Specifically, I see a 3.5" stud, 3.5", 2", 2", 3.5". Are these just 2x4s ...
0
votes
0answers
90 views

What is the difference between a C stud with a dent on the back and one without?

What is the difference between a C stud with a dent on the back flange and one with a flat back?
6
votes
3answers
23k views

Can metal studs support a 64" plasma TV on a swiveling mount?

Alright, I need a sanity check here. I've been tasked with mounting a 64" plasma TV with an articulating mount onto a metal stud wall in the corporate boardroom. It's the quadruple-threat with no room ...
0
votes
1answer
455 views

24" o,c, 2x4 for load bearing wall and rafters for workshed?

I'm making a small 12x16ft workshed. I want to go 24" o.c. on the walls and rafters (rafters may be 2x6, or 2x4 with supporting members), both for cost saving, and because it will create less thermal ...
1
vote
1answer
252 views

Possible to remove truss and add collar ties?

I am doing a pretty significant garage renovation and had a couple questions. I was originally going to just replace the loft (the original wasn't supported on top the stud wall on side which always ...
1
vote
1answer
45 views

What fastener to use to attach 4" circular pan to steel stud?

I need to attach a 4" circular pan circuit box to a steel stud in order to hang a bathroom vanity light fixture. The fixture weights less than 10 lbs, but assume some future homeowner will want to ...
2
votes
3answers
205 views

How do I know if I will drill into a hole in a wall that was already made?

I drilled 2 large holes for mounting a flat screen in the bedroom. One hole is in a wood stud and the other is a metal stud. I will be renting out our apartment and will be taking the TV down and ...
2
votes
2answers
380 views

Plumbing cuts through five studs. Is ok?

My kitchen remodel is in progress. After ripping out existing cabinets we found that the plumbing for the sink drain cuts through a total of 7 studs, more than 50% through each (see photos). ...
0
votes
1answer
104 views

How to build a sauna? [closed]

I would build my own DIY sauna, but I can't seem to find extensive information about it. Nor I can find plans to build one. How can I build one? My father has a lot of home building knowledge, but we'...
5
votes
2answers
184 views

What features do I need in a stud finder for use on plaster walls?

I have an old house built in the early 1930s. The conventional stud finders are useless on plaster. The more sophisticated ones are more expensive in the $50 range. What features would a stud finder ...
1
vote
5answers
7k views

How to fit 4" rigid aluminum duct vent in between walls when there is an angle brace?

I want to do what these people have done here: The problem is I have bracing going diagonally and it is not leaving enough space for the 4" aluminum duct vent. Can I saw the bracing off for the ...
2
votes
2answers
202 views

What's the point of a thin (1/4" width) piece of wood set diagonally between two studs?

What's the point of a thin (1/4" width, ~2-3" wide) piece of wood set diagonally between two studs? I just took out a piece of drywall for some other work I'm doing, and between two studs, there's ...
1
vote
2answers
2k views

Need to hang mirror, AC detected from stud finder

I'm a rookie with any sort of home renovation / improvement. My wife asked me to try and mount a mirror, its heavy, about 40 pounds. The mirror has two d-rings on the back and a big warning not to ...
2
votes
1answer
558 views

Can I attach a television mount using custom drilled holes?

I have a 94" wall with 14" studs. There is a stud right in the center at 47". I have been looking for a full motion mount wide enough, so that I can use the studs on both sides of the center. Meaning ...
1
vote
1answer
2k views

Can a condo interior room walls have steel studs that are paper thin?

I'm a bit puzzled about what's behind the drywall in my high rise condo built 3 years back. When drilling into an interior room wall supposedly where a stud should be(found by a stud detector and yes ...
2
votes
1answer
2k views

How do I go about framing a half wall into a full wall?

My house has an second floor open loft area with a half wall that overlooks the foyer down below. I would like to enclose the half wall, add a closet and door to create a fourth bedroom. How do I go ...
1
vote
3answers
1k views

How to make paint stick to a stud screw?

Around my house, I have a places on my walls where the paint has fallen off of stud screws. They are not popped screws. Rather, they are still depressed into the wall, so I don't know how why this ...
7
votes
2answers
26k views

If my wall has metal studs, is it better to anchor heavy objects through just drywall or also through the studs?

I live in an apartment that has that has metal studs. I'm considering hanging various things from the wall, including a coat rack that will span 5 or 6 studs. I've seen advice that says metal studs ...
1
vote
1answer
459 views

Notch rules or guidelines for steel studs (non-load bearing)

I'm trying to figure out what kind of notches (if any) are allowed in steel studs used for non-load bearing walls (for a finished room in a basement). IRC 2009 section 603 indicates that no notches ...