2
votes
1answer
67 views

Can I attach a television mount using custom drilled holes?

I have a 94" wall with 14" studs. There is a stud right in the center at 47". I have been looking for a full motion mount wide enough, so that I can use the studs on both sides of the center. Meaning ...
2
votes
1answer
142 views

How do I go about framing a half wall into a full wall?

My house has an second floor open loft area with a half wall that overlooks the foyer down below. I would like to enclose the half wall, add a closet and door to create a fourth bedroom. How do I go ...
1
vote
1answer
59 views

Notch rules or guidelines for steel studs (non-load bearing)

I'm trying to figure out what kind of notches (if any) are allowed in steel studs used for non-load bearing walls (for a finished room in a basement). IRC 2009 section 603 indicates that no notches ...
2
votes
1answer
86 views

Can I drill another set of holes in my studs to mount a TV?

I currently have a 47 inch TV which is mounted onto studs in my wall which is good. But now I plan to get 70 inch TV which means my existing wall mount frame must move a little upwards to fit above ...
4
votes
2answers
287 views

Why can't I find a stud in this wall?

I have problem locating my stud in my wall. I have tried many different ways to locate my stud but the results are weird. Using Stud Finder: The reading results are different everytime and weird. I ...
2
votes
1answer
354 views

What drill bit do I need to screw a hex cap screw into a wall stud? The magnetic DeWalt nut driver bits aren't an exact match

I am trying to hang a TV mount into the wall studs above a fireplace. The hex cap screws that came with the mount don't fit snugly into the 7/16" nut driver bit and are too big for the 3/8" bit. ...
0
votes
1answer
287 views

Small stud wall to sloping ceiling under stairs

We have an under-stairs toilet that we are replacing. The toilet was quite old, so the drain was 20cm from the wall. Apparently newer toilets require the drain to be pretty much flush with the wall, ...
3
votes
2answers
493 views

How to install coat hooks securely when holes don't line up with studs (batten depth?, length of screws?)

I have a single piece set of coat hooks to install on the wall. By single piece I mean that they are 6 double hooks all attached to a single piece of metal as backing. There are 3 holes in the ...
1
vote
1answer
990 views

How do I determine how much weight an indoor hammock mounting kit can bear?

I'm looking to mount hammock indoors using an indoor hammock hanging kit, and was wondering how I'd determine how much weight the wall studs or ceiling I attach this mounting kit into can bear. The ...
4
votes
1answer
525 views

How much movement is normal after mounting a TV on partition wall?

I have a wall that's made of plasterboards mounted on metal studs. I have mounted two DVD cabinets (each 22kg) and an LCD TV (40kg). To mount all this, I installed 6mm thick MDF panels across 5 of ...
1
vote
1answer
210 views

How can I block off a doorway with studwork on a brick wall?

I'm blocking up a doorway in a brick wall. I've decided to block it up using a stud wall as that should be a bit easier than bricking it up. I know that the bricks are 11cm depth plus approx 2cm ...
0
votes
2answers
322 views

How should I mount a TV to a wall that slants inwards 8 degrees?

I am going to attach a piece of plywood across 3 studs and then attach the mount to the plywood, as described in the answer to Studs not in right place for mounting TV. Can I use 2x4s to extend them?. ...
0
votes
1answer
2k views

Can I mount an 80" TV where only one stud is available? [duplicate]

Possible Duplicate: How can I mount a TV when I can’t find studs inside my wall? I am looking for some opinions here. When my electrician tried to mount my 80"TV above my fireplace, he ...
8
votes
3answers
2k views

Can I wall-mount a TV when there is an air gap between the drywall and the wooden stud?

I'm mounting a 38lb TV (with a ~10lb mounting bracket). I located a stud, but the drywall floats an inch above it, plus the drywall itself is another 1/2 inch. So a couple 3-inch screws (and not a ...
3
votes
2answers
26k views

How can I mount a TV when I can't find studs inside my wall?

WARNING: I'm not the greatest handyman. I bought a TV mount the other day, expecting to hang my heavy 40" TV above the fireplace. However, the instructions specifically say to first screw the mount ...
7
votes
4answers
4k views

My house has steel “2x4s” in the walls, can I hang cabinets, a TV, or some other heavy item from them?

The question is pretty much all in the title: My house has metal "2x4's" in the walls. Can I hang cabinets or a TV directly on these metal studs? If not directly, is there something special I must do? ...
4
votes
1answer
647 views

When installing new stud in existing frame, does the stud have to be the *exact* height of the inside of the frame?

I am about to install two new studs into my wall's frame. I noticed that the studs are about 1/16th of an inch shorter than the inner height of the frame. That doesn't appear to be a lot to a layman ...
1
vote
1answer
439 views

Hanging a new wall with Genie Clips and need to install a few studs. Will this affect the installation?

Here's what the bare frame looks like: If you don't already know how a wall is hung with Genie Clips, here's the video. Skip to 2:45 to see how they're spacing the clips. ...
4
votes
1answer
5k views

How do you frame a wall more than 8-10 feet tall?

I am capable of framing a "simple" 8' wide 8' tall 4" thick wall out of 2x4 lumber, then attaching plywood or drywall or OSB or any other sheet material to the frame. Making the wall wider is a ...
11
votes
4answers
9k views

Am I have trouble finding studs because my walls are lath and plaster?

i picked a tv mount from ikea. The tv itself is being mounted to some paneling which in turn is mounted to set of wooden draws. In addition, it gives you hardware to mount the panels to the walls. Its ...
4
votes
2answers
5k views

Does crown direction really matter when framing a wall?

When framing a wall is it really important to have the crown of each stud in the same direction?
10
votes
3answers
3k views

When should you use metal studs?

When does it make sense to use metal framing for an interior wall? What are the advantages to traditional wood framing?
17
votes
4answers
4k views

How do I find studs when stud finders won't work?

I was trying to hang my TV at my new place, on an interior wall (between living room and a bathroom). Using the stud finder on other walls worked fine, but on this wall I got some very strange ...