The tag has no wiki summary.

learn more… | top users | synonyms

5
votes
1answer
296 views

Am I doing something wrong with this sanding job?

I'm trying to finish a finishing job on a dresser; I abandoned the project (long story) a while ago after getting a few drawers done, and I've since lost the exact instructions I was following. After ...
6
votes
2answers
1k views

How can I remove tiny dust particles from the air?

As a basic prep step before I painted, I sanded some of my walls. Later, I cleaned the area and swept up any visible dust particles. Now however, a member of my family is having difficulty breathing ...
4
votes
3answers
742 views

What would cause a Varathane EZV sander to rip the sandpaper?

I have recently been appointed FSA at a Lowes store in Allen Park Michigan. I was ask if i could find out why the Varathane EZV sander was ripping the sand paper. My knowledge on the subject is ...
7
votes
1answer
108 views

What tools and techniques are available for sanding without machinery?

I am planning on creating a table made out of recycled wood planks and I am wondering if it is too ambitious to hand sand the wood planks without the use of machinery. I am on a budget and am ...
6
votes
2answers
212 views

Should we sand and prime holes in our walls or pay someone to do it?

We just had our 1,000-square-foot house insulated with blown-in insulation. Now we have 180 patched-up holes in our interior walls that need be sanded and primed before we repaint. The holes ...
8
votes
2answers
827 views

How is sandpaper quality determined?

In chat today, Karl mentioned that there's a very large disparity in sandpaper quality. Now, I knew about grit differences (they refer to the fineness of the grain, iirc) but literal quality? So, ...
2
votes
2answers
555 views

Can I hone Silestone from a glossy finish to a matte finish?

I would like to hone (make the glossy finish matte) my Silestone kitchen countertops. Is this possible either through an acid wash, sanding or other? Sanding works on samples but will be difficult ...
1
vote
1answer
79 views

Can I use 6“ hook and loop disks with a 5” sander?

A friend just gave me over a hundred 6" flat hook and loop disks. The only problem is, I've got a 5" orbital sander with dust collection which uses perforated sanding disks. Can I use these together ...
3
votes
3answers
1k views

Do I need to sand this unfinished table?

I've gathered that the step immediately before staining a table is to sand it. However, I wonder how to tell when the table is smooth enough? Can I skip the sanding step? In my case I bought an ...
15
votes
8answers
88k views

What grit sandpaper should I use between coats of polyurethane?

I'm planning on applying polyurethane to a pine bench I've finished staining. I decided on foam brushes for application, but I wasn't sure what grit sandpaper I should use between coats. Is 400 good ...
2
votes
2answers
320 views

Resurfacing a wood table

I have a 10 year old hardwood (red gum) table that has had a hard life. It was originally finished with bee's wax but I did not really keep up maintenance. What is the best way clean up this table? ...
4
votes
5answers
978 views

What's a good cheap sander to sand the ends of wooden blinds?

I need to sand down some wooden blinds because they are about a millimeter too wide for the old window frames they are going into. I'm trying to figure out a cheap and easy way to sand down about 6 ...
5
votes
5answers
10k views

What's the right way to sand/shave/reshape particleboard?

My second bedroom has low ceilings. I bought an IKEA closet, but somehow botched the measurements when I was seeing if it would fit. So, instead of having ~10cm of room for the top of the cabinet, I ...
5
votes
3answers
13k views

Is it necessary to sand before the last coat of oil paint?

When I'm painting high-gloss oil-based on woodwork (architraves, skirtingboards, windows), I have been following the tin's advice and sanding between all coats. I don't resent sanding after the ...
2
votes
2answers
434 views

Can oscillating “multi-tools” sand vertical surfaces?

I need to sand some rough spots on our old front door before repainting and am considering buying/using a multi-tool for this task (as well as some tricky flooring and drywall tasks later). What's ...