The tag has no usage guidance.

learn more… | top users | synonyms

6
votes
1answer
1k views

How can I repair rust damage on a steel shed?

I have a shed in my backyard that came with the house. It's made out of what I presume is steel sheet metal. Overall it's in good shape, but there is some rust damage on one side that is getting ...
4
votes
5answers
8k views

How do I rust-proof a metal pole?

I have a steel pole holding up part of my house. It is bolted to concrete footings. I am about to build a deck around but would like to rust-proof the bottom before I do this to prevent any future ...
3
votes
2answers
7k views

How do I repair a garage door with a rusty bottom?

Was looking at my garage door as I pulled into home yesterday and noticed that the bottom panel is starting to rust slightly at the bottom. The rust looks like a small mountain range from one side to ...
3
votes
2answers
116 views

How to protect exterior galvanized flashing?

With ships, they'll bolt zinc blocks on, can I "re-galvanize" metal? I ask as I have some flashing that was likely installed in 1938. It was galvanized and is in reasonably good shape. But replacing ...
2
votes
2answers
3k views

Should I remove rust from my gas meter?

My home is about 8 years old. Despite being painted, my external gas meter has rust at every thread/joint location. The rusting is mainly on the pipe threads. I'm afraid this could eventually lead to ...
2
votes
3answers
67 views

Rust at Bottom of Support Column

I'm just wondering how serious this is and also what are my options for fixing it? Best solution would be to replace the plates and column. How much work (cost) is that?
2
votes
2answers
964 views

How to repair (and is it worth the trouble to) a rusty dishwasher rack?

I've seen a couple of solutions: Dishwasher paint, like Uber Goop Silicon Vinyl paint But some reviews of some of the "paint" products say it doesn't last long. If this is only a temporary repair ...
1
vote
3answers
11k views

Is it OK to re-paint a gas-range grill with paint?

I have a gas range (gas stove - indoor) for cooking, and the metal grate that goes over the top has some areas of rust. If I was to sand down the rusty areas, would it be advisable to paint it with a ...
1
vote
3answers
1k views

Metal conduit balusters

I'd like to use galvanized metal conduit as deck balusters with pressure-treated lumber. Will the bare metal resist rust? If not, is there an inexpensive way to improve its rust resistance?
1
vote
2answers
4k views

How should I protect the metal of a power rack that's kept outdoors?

I plan on building a power rack for my home gym and was wondering what kind of metal/coating I should use when building it since it will be stored outdoors. Most commercial power racks are built using ...
1
vote
1answer
44 views

How can I treat or replace steel bolts in aluminum nuts to avoid corrosion?

I have a structure originally built from aluminum extrusion with channels using aluminum T-nuts and steel bolts. Over the years, the steel bolts have rusted, making them prone to stripping at the head ...
1
vote
1answer
160 views

Repairing wire dishwasher racks [duplicate]

Possible Duplicate: How to repair (and is it worth the trouble to) a rusty dishwasher rack? We have a dishwasher with wire racks on the inside. The racks have a plastic coating on them, but ...
1
vote
3answers
212 views

How can I get new sections of fencing to match the existing fencing?

I have a lot of Fencing. half of the fence has previously been Galvanized, I have also created a few new fence sections. My problem is that when the new fence gets galvanized, it will look too clean ...
0
votes
2answers
98 views

What kind of grease can be used on outdoor screws to avoid rust

I have fixed some screws outside to mount a house number onto masonry. I feel like I should probably apply some sort of grease or water repellent to avoid rust as they will be exposed to rain ...
0
votes
2answers
117 views

What type of sealer/stain to use on untreated cedar 4x4 lumber glued together

I'm planning on making a heavy bench top by using six 4"x4"x6' posts, and gluing the faces together with Elmer brand carpenters glue and several large bar/trigger clamps. Afterwards, I'll just ...
0
votes
1answer
708 views

How to fix metal bulkhead holes caused by rust

At the top of my bulkhead in the center of the seam where the water drains, there are some holes caused by rust. Each about 1/2 inch in length, 1/4 in height. Since the rest of the structure is ok, ...
0
votes
0answers
149 views

Repairing rust damage and dents on my standby car

My standby car has got some nicks and minor small dents. Also there is some rust damage on two of the doors and part of the fender, usually spots where dew drop collects. At some places the rusting ...
0
votes
1answer
67 views

How to protect a lock against rusting

For reasons, I'm going to put a D lock through the wall of my flat, and I want to protect it against sealing up with rust. There are coincidentally a pair of perfect holes already in the wall (from ...