0
votes
0answers
17 views

Kenmore washing machine leak

I have a puddle of water under my machine after my Kenmore 110-21252110 is finished and I can hear water at the bottom of my outside tub when I jostle it around. I took off the pump and assumed that ...
3
votes
2answers
66 views

What test can I do to my washer's gearbox to determine whether or not it is bad?

I have a Kenmore washing machine (model 110.92273100) that doesn't spin. I've taken the gearbox off, and when I spin the input shaft (motor coupler), it seems to act the way I would expect. When I ...
2
votes
1answer
118 views

What could cause washing machine drum to bang against housing during spin cycle after a repair?

I just replaced the agitator cam and cogs and drive block in my Whirlpool top loading washing machine. I put everything back together exactly according to directions and now the outer drum seems to ...
3
votes
2answers
1k views

How do you access under a front loading washing machine drum to remove a trapped coin?

We had a coin trapped under our front loading washing machine drum (found out after it was removed). The washing machine engineer got it out by prising the lip of the inside of the drum upwards, ...
0
votes
2answers
248 views

How can I repair this washing machine that I think has had the chip wiped?

I have been having a huge problem with my washing machine and I think that it's because the chip program is wiped or a problem with the EEPROM. Here's a video showing what happens when I plug it in ...
2
votes
1answer
687 views

How can I repair the agitator on my hotpoint washer?

Could anyone please advise me how to remove the agitator on a hotpoint washer model HTWP1200DOWW? The agitator is not spinning.
2
votes
2answers
2k views

How can I repair the start button on my LG washing machine that is hard to press?

The start button on my LG washine machine WD14700RD is very hard to press, and getting worse. I need to lean on it with my whole body weight in order for the program to start. All the other buttons ...
2
votes
2answers
3k views

What's causing my washer to stop running during the wash cycle?

I have an Frigidaire Affinity washer that runs perfectly fine, (all the way through wash & rinse cycles), when empty, but as soon as you put even a small load of clothes in it, it stops working ...
0
votes
2answers
189 views

Should I repaint this dryer part?

on a combination washer/dryer, there's one metal part called the dryer duct, where water vapor right out of the drum is heated some more before going to cold water bath to condensate. That vapor ...
1
vote
0answers
269 views

Would this buildup cause “dHE” error on an LG Tromm dryer?

Got the machine off craigslist. During the drying cycle it stops and shows the error. The user manual tells that with dHE error I should inspect the water supply, if the water supply is within spec, ...
1
vote
1answer
58 views

What are these parts described by the service manual?

The service manual for a LG WM3677HW shows a very bad diagram... and I'm not very familiar with the parts to ID them. The image above tells me to probe 3 components, and if out of spec replace ...
3
votes
1answer
1k views

What would cause my washing machine to stop at the rinse cycle and smell?

My wash machine fills with water and washes just fine. Then, when it is supposed to empty at the rinse cycle, it stops. There is a slight burning odor. If I wait a half hour I can start it back up. ...
0
votes
1answer
159 views

Should I cancel our appointment with the repair tech for our washing machine?

I have a 6 1/2 months old washing machine. Last week, we started having issues it. It would drain some of the water out, but not all of it. It also made a horrible racket all the way through the ...
2
votes
1answer
985 views

Why won't my washer spin even though it still agitates?

I have a Kenmore 80 series washer and it recently stopped spinning and agitating and I found out it was the coupler. So I changed that and it start to work again, normally. After a week or two it ...
1
vote
0answers
158 views

Why won't the lower agitator on my washing machine spin?

I have a Whirlpool top load washing machine. I recently replaced the dogs on the agitator which was very easy. The top agitator works like it is supposed to, but the bottom doesn't move. It's like ...
1
vote
4answers
17k views

What could cause my washing machine to stop before the rinse cycle?

My washing machine will get stuck right before the rinse cycle. The washing machine will be full of water. The way to "fix it" is to twist the knob right after the "rinse" line, find the sweet spot, ...
2
votes
2answers
758 views

My washing machine stopped working. Should I replace, repair or call a technician? [closed]

I have a Whirlpool front-loading washing machine (not sure about the model at this moment - I'm slacking off at work right now ;P). A month ago the torque transmitting belt went off. I put it back on ...
4
votes
1answer
4k views

How should I repair damaged enamel in a clothes washer?

We have noticed recently that when clothes are left in the washer for more than the "usual" waiting time that they sometimes pick up rust spots. On inspection of the wash tub, I found that several of ...
1
vote
1answer
440 views

How can I determine the cause of a noisy spin cycle in my INDESIT washing machine?

My washing machine has suddenly started being much noisier during the spin cycle. It doesn't seem to be vibrating or knocking/banging. It's just got a much louder whine when spinning fast than it ...
2
votes
1answer
499 views

How do I replace a Zanussi washing machine's front door seal?

I have a zanussi jet system 1200, model wjd1257w. It is a washing and drying machine. It leaks water, I guess at the spin cycle or perhaps before it. I searched and found out that it could be either ...
0
votes
3answers
3k views

Top Loading Washer Leaks from bottom of machine.. Usually Worth Repairing, or Time to Upgrade?

I have an old whirlpool top loading LA8800 (Maytag rebranding?) washer that leaks from the bottom.. is this usually a simple (and cheap) gasket type repair, or would now be a good time to get a more ...
1
vote
3answers
238 views

Identify a washing machine part - the exit port

I'm trying to identify (= find the name for) a washing machine component. Unfortunately, I don't have this part - I gave it to my landlord who is looking for a replacement. It's basically the exit ...