The tag has no wiki summary.

learn more… | top users | synonyms

0
votes
2answers
52 views

Can you use a power drill with the exchangeable screwdriver bits on a manual screwdriver?

If not, what is the difference between a screwdriver bit that is designed for a power tool versus the ones that come with a multi-bit screw driver set like these: ...
3
votes
2answers
60 views

Does the number of links of a chainsaw chain affect the sprocket?

How does the gauge of the chain effect the drive sprocket? I bought a new bar and chain, the pitch is .325, the sprocket is .325 and gauge is .063, but the number of links is 81 instead of 74. Will ...
2
votes
2answers
150 views

Cheap power tools for large number of cuts of aluminium profile lengths

I need to make some 200 cuts of aluminium profiles. Examples of what I'll be cutting: Hollow box profile, 40mm x 40mm x 3mm: 40 pieces of 400mm lengths 12 pieces of 1500mm lengths Hollow box ...
0
votes
3answers
77 views

Can I use a 120 volt 50/60 Hz. tool on a 230 volt 50 Hz. circuit?

I want to get the Dewalt DW660 cut out tool, it has been made for the north american market so it runs on 120 volts. It has the following specs: 120V ~ 50/60 Hz 5 Amps 600 Watts The voltage ...
3
votes
4answers
3k views

Should I rebuild or just replace worn out cordless tool batteries?

I have a couple of older Porter Cable 19.2v Ni-Cd batteries which have worn out. In shopping around for replacements, I've noticed there are a number of businesses which offer to rebuild your ...
13
votes
3answers
6k views

When should I replace a circular saw blade?

Is there a rule of thumb for how often a circular saw blade should be replaced? Is visually inspecting the blade condition enough?
3
votes
2answers
283 views

How can I fix the guard on my mitre saw?

I've owned an Evolution Rage-3 mitre saw (http://www.evolutionpowertools.com/uk/build/rage3.php) for about fifteen months. About a week ago the guard that covers the blade started to stick, and now it ...
1
vote
1answer
49 views

Does an adapter exist that can convert a rotary tool in a oscillating multi-tool one?

I saw in the Internet a power tool with a proprietary attachment system that can transform the power base in a drill, in a cutter, in a jig saw, in a multi-too and so on... more than 10 different ...
0
votes
1answer
57 views

Gold-standard drill make? [closed]

Craftsman:wrenches as BLANK:power drills What is the gold-standard power drill make? For general purposes/light carpentry.
5
votes
5answers
4k views

As a beginner woodworker, should I buy a table saw or a band saw?

I'm just getting into woodworking and don't have any equipment, not even a bench. As a beginner looking to maybe make anything from small boxes to light furniture, should I buy a table saw or a band ...
0
votes
0answers
320 views

How could a power drill trigger switch be damaged when used continuously in variable speed range?

I just acquired a DeWalt DCD790 cordless brushless drill/driver, and going through the manual, on page 10 under Speed Trigger Switch, I find the following: NOTE: Continuous use in variable speed ...
1
vote
0answers
36 views

How can I remove the armature on my Porter Cable trim saw?

I have a Porter Cable model 314 trim saw. When using it the other day, it stalled in the cut. Ever since then, it sometimes will not turn on, but you can move the blade just a tad and will turn on. ...
1
vote
2answers
46 views

Can buffing and sanding attachments be used with a fixed speed powerdrill?

Have wondered about this possibility. I've seen some 'As seen on TV' ads where they sell all-in-one DIY power-tool kits which can act as a drill (reversible), power screw in/unscrew, hammer, buffing, ...
1
vote
1answer
55 views

What size drill motor should I buy?

Looking to buy a non-professional (occasional home DIY use) multi-purpose power-drill like the 'Skil' range by Bosche (although I am open to other brand / makes that fit my budget). I have an option ...
5
votes
5answers
14k views

What is a good way to cleanly cut through steel?

What tools can I use to get a clean cut through thin steel? Specifically, I have several mini beer kegs I need to cut the bottoms out of. I don't mind it taking a while, but my cuts are jagged (easy ...
1
vote
2answers
143 views

What factors are important when selecting a rotary tool?

I'm fairly new to the DIY scene, so to say that my working knowledge of any power tool is minimal is an understatement! I'm currently embarking on a DIY project that requires cutting acrylic boards, ...
2
votes
2answers
256 views

What types of tools are required for making wood toys and models?

I am learning and doing some woodwork, and I have been using a hand saw and sanding to make very simple wood blocks. I would like to know what tools are suitable for toys like this puzzle and these ...
12
votes
5answers
4k views

How do I consistently drive drywall screws to the correct depth?

Is there a special technique or tool for consistently placing drywall screws correctly? I'm using a standard Dewalt DWD115K (with no auto-stop mechanism) so I'm usually paranoid of going too deep ...
2
votes
1answer
199 views

How can I replace a NEMA 6-30 cord & plug with a NEMA 14-30 cord & plug?

I recently purchased a used SA-6E compressor from a dive shop I work with. I had to switch out the NEMA 6-30 plug to a NEMA 14-30. This was done with a complete new plug and cable. I connected the ...
3
votes
7answers
42k views

How do I remove a drill bit that is stuck due to an overtightened chuck?

I recently bought a Bosch PSB 500 RE power drill and already I kinda screwed up the machine. The chuck is keyless, consisting of two parts which I'll refer to as the head and the base. You would ...
10
votes
3answers
496 views

Should I get a keyed chuck for cordless drill?

I am thinking of getting a Milwaukee M18 fuel drill/ driver combo. The drill is insane with 750in-lbf of torque. It comes with a hand tighten chuck though. My other Milwaukee corded screwdriver has ...
3
votes
3answers
2k views

How to cut exact and identical rectangles with a circular saw?

Following this question What tools do I need to make a straight cut in laminated chipboard? , I bought a circular saw. So far, I used it to make long straight cuts which didn't require high ...
1
vote
1answer
267 views

Is there any way I can use regular dremel bits on a dremel trio?

A few years ago I bought a Dremel Trio, which uses much more expensive bits than a regular Dremel. The collets are also different. Consequently I never really used it. Now I'm making a custom cnc ...
0
votes
0answers
44 views

Die grinder collets

My Chinese die grinder has 2 collets for 6mm and 3mm tools. As far as I see, collets used in my grinder seem to be of "dead length" kind. If possible I would like to use it with my other tools of ...
5
votes
2answers
970 views

Is it safe to charge a DeWALT 18v battery if the charger emits a whining noise

I have 1 DeWALT 18 volt NiCd batteries. One charges without incident. If I attempt to charge the other, a whining noise is emitted from the battery or charger. Is it safe to attempt to charge this ...
0
votes
2answers
105 views

Can I realistically replace my drill with a rotary hammer?

I find myself needing to do more and more stucco and concrete chipping work that is suitable for purchasing a rotary hammer. Can anyone here tell me if such tools can entirely replace a normal drill? ...
11
votes
3answers
2k views

What type of cordless tool battery chemistry should I purchase?

I'm about to buy a cordless tool set in which the tools all operate off the same form-factor battery. The batteries come in several different chemistries and I'm wondering which type is better for ...
2
votes
4answers
405 views

How to slightly enlarge a worktop hole for replacement kitchen sink

The task I am replacing my kitchen sink. The existing sink sits in a rectangular hole (with rounded corners) in the kitchen worktop. The worktop is about 1½" (40mm) thick and is made of some kind of ...
1
vote
2answers
345 views

Rotary hammers, how many joules to hammer through concrete slab?

I'm in need to buy a rotary hammer to make some holes in a slab about 12 cm thick of armed concrete. The holes will be between 5 and 10 cm in diameter, so I will have to hammer a round opening instead ...
3
votes
2answers
649 views

What could cause a battery hedge trimmer to have white smoke come out of it?

For the most part my hedge trimmer was doing a really great job. I did have a little trouble with the thicker stems, so I would swing the trimmer at the stems while cutting, which helped. However, a ...
2
votes
2answers
1k views

Can I put a sanding drum in a routing table and use it like a spindle sander?

If I mount something like one of these: in a router in a router table, have I just created a spindle sander, or are there other differences in how they work? If you've already got a router, what ...
7
votes
2answers
2k views

Cutting a Custom Threshold: Best Tool for the Job?

I am in the process of creating a custom threshold to go from a tiled surface down to a carpeted surface. The tile is about an inch above the carpeted floor, so I decided to make a custom threshold in ...
0
votes
2answers
246 views

Can you get an “optionally cordless” or “hybrid” drill? [closed]

I'm looking to buy a new drill, but all of them seem to be corded or cordless. Are there drills that can either run cordless, or off the mains, depending on whether it's plugged in? It seems that ...
4
votes
2answers
3k views

Why won't my circular saw blade tighten on the spindle?

The blade on my Craftsman circular saw will not tighten down and consequently slips on the spindle. I've tried packing the bolt with a washer and it didn't help. Can't find anything online so this ...
1
vote
1answer
60 views

Is it possible to get a magnetic mount to attach to my aluminum tablesaw base?

I want to use a magnetic base and precision deflection meter with my tablesaw, which has aluminum instead of cast iron table, which means it is not a magnet-friendly material. I'm wondering if anyone ...
3
votes
2answers
217 views

Should I be concerned about wearing out the clutch when driving screws with my drill/driver?

The clutch on a drill/driver is used to limit the amount of torque applied when driving screws. However, as the clutch is a mechanical part subject to wear especially when it slips, I'm concerned ...
1
vote
1answer
59 views

Are router bit imperfections normal?

I just got my first router and purchased some Freud bits for it. However, I noticed that a few of them have pitting at the base where the cutter joins the shank. Is this normal for router bits, or is ...
2
votes
1answer
241 views

How safe is this power configuration?

I have a regular 2 socket, 15 amp outlet in my garage. I need to run my miter saw and shopvac at the same time, the saw draws 15A and the shopvac 8.5A. I've currently been running them off one ...
2
votes
1answer
4k views

Is it bad that my cordless drill is smoking?

I was using my cordless drill today. I was trying to drive a bolt that was stuck with my drill in low gear and it wasn't really budging. I tried a few times and then noticed that smoke was coming ...
7
votes
3answers
5k views

What tools do I need to make a straight cut in laminated chipboard?

It's 38mm thick. Next week I will need to cut it along a straight line, and I would like the cut to be as straight and clean as possible. What tools do I need to do this ?
1
vote
0answers
79 views

How much do I lose on Dremel power from a flex shaft

I would like to mount my Dremel 4000 so I can use it as a stationary tool, e.g. a self-made CNC. There are several pages on the web and many videos on youtube showing the Dremel fixed in a box-like ...
1
vote
3answers
428 views

Is it safe to cut throught a 70mm spruce beam with a Metabo jigsaw?

I have this jigsaw: Metabo Ste 90 SCS (610 watts). So far, I'm using it to cut 1cm to 2cm thick wood, and it's a great tool. I know that the right tool to cut this beam would probably be a miter ...
-5
votes
1answer
72 views

Enermax Pro87+ Gold 500W adapter? [closed]

I'm looking for an adapter for my fridge to my power supply. Is this even possible? My fridge is just an ordinary one? Could that save a few euros?
2
votes
2answers
1k views

Best Technique to Achieve Perfect Cut-Outs in a 2x4

I am building a ladder similar to the one pictured. I want to cut hand-hold holes like the ones in the image. I am horrible with a jig-saw, and I don't think I could ever get them looking as nice as ...
0
votes
1answer
155 views

What type of adapter should I use to turn a cordless drill in to a corded drill?

I have old Bosch PSR12 driver/drill that all NiCA are dead. I've modified it successfully to work as Corded after removing batteries and connecting 12V 1.5A (220v) adapter. The drill works but when I ...
11
votes
5answers
4k views

How can I protect my hands when using power tools?

When doing many DIY projects there's a strong need to protect hands against cutting by sharp part edges. Gloves seem a natural solution. However recently I was mounting a countertop and wearing ...
2
votes
1answer
223 views

Can I plug a 15A snow thrower into a 15A receptacle?

I'm planning to buy a snow thrower with a 15A motor in it. I have an outside receptacle that's rated for 15A and so is the breaker in the electrical panel. I'm wondering if this will work without ...
-3
votes
1answer
72 views

Is there a huge difference between 1.6amp and 3amp power usage?

I just want to know if there a huge difference between 1.6 amp and 3 amp power usage.
4
votes
3answers
2k views

What tool do I need to cut groove along edge of floorboard

Very simple question really - I have a floating wooden floor and a raised stone hearth in front of the fireplace. I want to run some cables along the edge of the hearth and I need to lift the floor ...
0
votes
2answers
611 views

Do I ever NEED to remove the angle grinder guard?

As the title says. Is it ever NEEDED to be removed? I read somewhere that when sanding or using the flat wire I should remove it, elsewhere I read that wire cup brushes must be used with a guard. Is ...