0
votes
2answers
35 views

Can I realistically replace my drill with a rotary hammer?

I find myself needing to do more and more stucco and concrete chipping work that is suitable for purchasing a rotary hammer. Can anyone here tell me if such tools can entirely replace a normal drill? ...
3
votes
2answers
141 views

Should I be concerned about wearing out the clutch when driving screws with my drill/driver?

The clutch on a drill/driver is used to limit the amount of torque applied when driving screws. However, as the clutch is a mechanical part subject to wear especially when it slips, I'm concerned ...
0
votes
0answers
110 views

How could a power drill trigger switch be damaged when used continuously in variable speed range?

I just acquired a DeWalt DCD790 cordless brushless drill/driver, and going through the manual, on page 10 under Speed Trigger Switch, I find the following: NOTE: Continuous use in variable speed ...
0
votes
1answer
120 views

What type of adapter should I use to turn a cordless drill in to a corded drill?

I have old Bosch PSR12 driver/drill that all NiCA are dead. I've modified it successfully to work as Corded after removing batteries and connecting 12V 1.5A (220v) adapter. The drill works but when I ...
0
votes
2answers
164 views

Can you get an “optionally cordless” or “hybrid” drill? [closed]

I'm looking to buy a new drill, but all of them seem to be corded or cordless. Are there drills that can either run cordless, or off the mains, depending on whether it's plugged in? It seems that ...
3
votes
5answers
25k views

How do I remove a drill bit that is stuck due to an overtightened chuck?

I recently bought a Bosch PSB 500 RE power drill and already I kinda screwed up the machine. The chuck is keyless, consisting of two parts which I'll refer to as the head and the base. You would ...
5
votes
1answer
1k views

What units are the clutch settings on a drill?

I have tried looking around the internet for an answer - but I can only find articles that explain what the clutch on a drill does. I am very familiar not only with what they do but also with how ...
4
votes
3answers
701 views

Will neodymium magnets harm my power drill battery?

I glued some magnets onto my power drill battery to use for storing drill bits on - but will the magnets affect the battery life?
10
votes
3answers
378 views

Should I get a keyed chuck for cordless drill?

I am thinking of getting a Milwaukee M18 fuel drill/ driver combo. The drill is insane with 750in-lbf of torque. It comes with a hand tighten chuck though. My other Milwaukee corded screwdriver has ...
16
votes
6answers
24k views

When would one use an impact driver versus a regular drill?

Or vice-versa. As best as I can tell, the impact driver is very good for most any type of screw going through wood. When would you use a drill (with screw bit) instead?
10
votes
5answers
8k views

How to drill a hole in a space too small to fit a standard manual or electric drill?

I have a very narrow kitchen cupboard I'd like to make some changes to (add shelves maybe). Almost any change will require drilling holes though, and there's not enough room for a standard electric or ...
7
votes
1answer
3k views

What do the numbers on a cordless drill mean?

I have a Hitachi cordless drill: You can turn the gray numbered part to switch between, hammer drill, drill and screwdriver mode. The screwdriver mode is numbered up to 22. Can someone explain ...
5
votes
1answer
502 views

Should I lubricate the motor in my power drill?

I have a power drill that looks like the picture below. I've had it for years, but recently I noticed that it squeaks when I use it (I only really hear the squeaking while it's winding down, when it's ...
11
votes
3answers
1k views

What type of cordless tool battery chemistry should I purchase?

I'm about to buy a cordless tool set in which the tools all operate off the same form-factor battery. The batteries come in several different chemistries and I'm wondering which type is better for ...
11
votes
5answers
3k views

Is there a technique or tool for consistently placing drywall screws correctly?

Is there a special technique or tool for consistently placing drywall screws correctly? I'm using a standard Dewalt DWD115K (with no auto-stop mechanism) so I'm usually paranoid of going too deep ...