Questions related to the construction, modification, maintenance, repair of the many functional systems included in a kitchen. Systems include: plumbing, electrical,lighting, major appliances, surfaces (wall, floor).

learn more… | top users | synonyms (1)

6
votes
1answer
5k views

How do I put up a travertine tile backsplash?

I'm trying to put up a tile backsplash in the kitchen (approx 25 sq ft) and I'm having trouble deciding between mastic and thinset for putting it on the drywall. For that matter, is it OK to put the ...
9
votes
2answers
32k views

How many CFM for a range hood do I REALLY need?

I like to cook. I would like to put in a fairly powerful range (nothing huge, though; I don't need six burners and a griddle), and will need a hood that can carry smoke, heat, steam, grease, etc. from ...
2
votes
1answer
5k views

Can a range hood vent have a 90 degree bend and vent out the wall?

I know I need to check my local codes before proceeding with this. that will be done but I first wanted to ask this community for advice. i'm going to have my kitchen gutted to the studs in a couple ...
5
votes
1answer
532 views

What is this component that connects to the garbage disposal?

I am trying to install a new faucet with a soap dispenser. I removed my old facuet; however, where the soap dispenser is supposed to go, this is here: It has pipes that go to the sink erator under ...
4
votes
4answers
6k views

How do I install cabinets on a floating hardwood floor?

We just purchased a bunch of cabinets for installation of a bar / kitchenette in the basement. There are 4 wall cabinets and four base cabinets. These are going to be installed on the existing ...
7
votes
5answers
9k views

How can I add a carbonated water tap in my kitchen?

I love carbonated water, but am sick and tired of buying it in bottles. There are home water-carbonating appliances like SodaStream, but I prefer not to have another countertop appliance. Can I ...
13
votes
3answers
21k views

Which Kitchen outlets do NOT need GFCI?

I have the 2 circuits in the kitchen with GFCI outlets, but I'm not quite sure which other ones do NOT need GFCI. Other circuits in the kitchen include Microwave, Fridge, and Dishwasher. It makes ...
11
votes
4answers
33k views

How do I properly wire GFCI outlets in parallel?

I have two countertop outlets in my kitchen that I am in the process of replacing with new, GFCI-protected outlets. These two outlets are on a circuit together, and they are the only loads on that ...
5
votes
2answers
1k views

Can an HRV replace the air exhausted by a range hood?

I'm in the process of buying a 1950s ranch house. It doesn't have the greatest insulation, so I'm planning to do some improvements over the first few years to tighten things up. I'll certainly do the ...
6
votes
3answers
18k views

How do we convert our drop-in sink to an undermount one?

We are in the process of remodeling our kitchen and are trying to narrow in on our sink for our new granite counters. We like the Kohler Staccato with unequal bowls and would like to have it ...
5
votes
3answers
10k views

How should I tile under kitchen cabinets?

I currently have tile on the floor of the kitchen that just butts up to my cabinets. I plan to change the floors and also change the cabinets. Is is best to rip out all the cabinets and tile, and ...
8
votes
3answers
2k views

Dowel joints in plywood

I plan on replacing my kitchen cabinets later this summer. The old ones were home made by the previous owner and are oddly sized so I need to make my own out of plywood. Is it possible to put dowel ...
5
votes
2answers
214 views

Why do my appliances show two sets of power consumption ratings and which one applies to my house?

Aptos, CA, USA I'm trying to determine how much power my electric oven is using (as part of a larger project to possibly upgrade our electrical service (with help from a licensed electrician of ...
5
votes
3answers
1k views

Can I bore my own hinge holes?

I'm scheming to reface my kitchen cabinets with sustainable lumber (looking for FSC certified or salvage) and trying to figure out what my options are. Our existing hinges aren't much different from ...
5
votes
3answers
637 views

How can I replace a kitchen cabinet hinge with no visible screws?

My kitchen cabinet hinge is broken. I want to replace it, but not really sure how because it is attached to the cabinet door without any screw (1). Anyone know a proper way to detach the hinge?
4
votes
2answers
541 views

Suggestions for a kitchen layout for my house? [closed]

We have just started to renovate our newly bought apartment. It is part of a very nice old building located in the center of Granada Spain. The apartment is approx 120m2 and we are in the process ...
3
votes
2answers
2k views

Should I use mastic or thinset for ceramic tile backsplash in kitchen?

I am about to install a tile backsplash in our kitchen, using these tiles, in 2" x 4" "mosaic" sheets. When I tiled my bathroom I used thinset (unmodified on the floor and modified on the ...
3
votes
1answer
667 views

Replacing gas oven with electric

I have a gas oven which has given up the ghost and I want to replace it with an electric pyrolitic oven. Do I need a separate circuit for the new oven, or can I put it on the normal ring main.? The ...
1
vote
4answers
6k views

Breaker being tripped - Oven or wiring?

Recently, our oven was left on all day, and sometime during the day it tripped the breaker. Now, whenever the oven is used (only for heating pizza, so 10-15 minute timeframe), the breaker trips ...
1
vote
1answer
1k views

When making kitchen cabinet doors out of plywood, what details will impact the final product?

I really want to replace our overwrought, baroque cabinet doors with flat panel doors. I want them to look good but I actually like the look of plywood. It seems from what I've read like I have to ...
0
votes
1answer
40 views

How should I finish the area around the gas line for my range?

We are remodeling our kitchen and had a new gas line run for our range. What's the best way to finish the area around the valve? We'll obviously will need to access the valve and run flex pipe from ...